Question about Computers & Internet

2 Answers

HP dv6000 it turns on. nothing comes on screen..? removed batteries, took totally apart. put it all back together making sure to clean out nicly, no luck. any idea's im guessing motherboard or bios??

Posted by on

  • Wesmorgan Dec 12, 2007

    no it dident work. when its turned on it seems like it restarts itself every aprox 5 seconds if that helps... im stumped

  • Anonymous Feb 08, 2008

    I have exactly the same problem.Turn it on,light on control panel seem to work but nothing on screen and after 5-10 sec it off and again turn on itself..

    HP DV6000

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 163 Answers

These are full of Problems also.. Its a No POST/BOOT Scenario and it could be a number of things. Try Pulling the Battery, Leaving the Adapter unplugged, Hold the power button down for a full 30-45 seconds, Plug the adapter in and retry. If it does not POST swap CPU/RAM with known good working components and if this does not help post back we can do more.

www.ikenfixit.com

(At least these use TSOP RAM for the Video chipset which is more stable than prior HP's And the Samsung BGA)..

Posted on Jan 16, 2008

  • Ken LaDere Jan 16, 2008

    Be sure if you pulled the heatsink off the CPU didnt stay connected. If it did you need to carefully pry it off, Unlock the CPU socket and reinstall also. Weve ran into this before. (Did you see a bunch of gold pins coming from the bottom of the heatsink after tearing it down)? (Not on the systemboard the heatsink as they have a thermal paste/grease that does not like to let go at times)..



    Ken

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 57 Answers

Try an external monitor. If that works then there is a problem with the screen cable, which is replaceable.

Posted on Dec 12, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I took apart my sewing machine, Brother CE1100PRW, to clean, and "Error 1" would not go away, please help.


Brother says:

The foot controller was pressed (or the start/stop button was pressed if the foot controller is not connected) and the reverse/reinforcement stitch button was pressed while the presser foot is raised.

Lower the presser foot lever before continuing the operation.
An E1 message appears on the panel Brother

Apr 13, 2018 | Brother Sewing Machines

1 Answer

Wine spilled on camera


For sure your buttons are contaminated. About all one can try in this case is to take the camera apart and spray some electrical contact cleaner to try to clean it up as best you can. There are usually 5 or 6 very small phillip's head screws that hold the camera body together, but you will have to be careful taking it apart since the back of the camera is connected to the main board by ribbon connector(s). You can carefully lift the tabs on them, and disconnect them, then inspect the camera for areas that were possibly effected by the spill. Spray them good with the cleaner, and allow them to totally dry, before turning the camera back on. You can reconnect the ribbon cables to test the camera before putting it back together, and, with any luck, get it functional again. Oftentimes the damage is too severe to be remedied, even with a good cleaning, but there is always a chance. If you need to know more about the procedures of disassembling the camera, there are many videos on YouTube that show how, just looks for videos on "Digital Camera Repair". Sometimes you can get lucky and find your make and model, but they're all basically the same, with minor variations. Good luck, hope this helps, and hope you get it back into working condition!

May 28, 2010 | Olympus FE-340 Digital Camera

1 Answer

I took it apart to clean, and now I barely cuts


Make sure the blades are even. It sometimes is hard to match when you take them apart. If they are even off a little bit they don't work. good luck

Oct 11, 2009 | Vidal Sassoon VSCL828 Hair Trimmer

1 Answer

Hp not turning on laptop


you haven't got the TFT cable plugged in correctly

Jul 25, 2009 | Computers & Internet

1 Answer

Saeco Coffee machine water tank empty


It is possible that the water sensor on the back panel of the machine is not operating, you will have to remove the back panel and check the sensor with an ohmsmeter.

May 18, 2009 | Saeco Royal Digital Plus Coffee...

1 Answer

Total power falure


TIPS:
1.)NEVER PUSH THE LENS IN AFTER CAMERA DIES, BUY A NEW BATTERY IMMEDIATLY AND TURN IT BACK ON, CLOSING THE LENS!

2.)NEVER USE AN AC ADAPTER, USE A RECHARGEABLE BATTERY OR A REGULAR BATTERY!

..to fix this...

Do as i say..

1.) Remove battery
2.) Remove front plate (screw driver may be needed)
3.) Check all gears, make sure they are correctly fitted in place)
4.) Move the gear manually to make the lens come out.
5.) keep it out, put the front plate back together.
6.) reinsert the battery, turn it on.


or...
1.) Remove the battery.
2.) Wait about 6-8 hours.
3.) Reinsert the battery.

or...
1.) Remove the battery.
2.) Try hooking it up through AC adapter, put correct voltage.
3.) Try turning it on.
4.) Remove AC adapter, reinsert battery.
5.) Turn it on.
If nothing happens just tell me..

Hope this may help;

Regards,
VOTIT

Sep 19, 2008 | Fuji FinePix S5000 Digital Camera

2 Answers

Re: view finder screen


I would suggest you to take it to some camera stores and get it cleaned.Because if u try to remove the camera and fix it,it might work fine it might completely kill the camera.So why u wanna take risk while there are ample stores near you.It wouldn't cost much........

Aug 25, 2008 | Canon PowerShot SD750 / IXUS 75 Digital...

1 Answer

Gateway 450sx no power


Needs physical repair. No help without some new parts. The "little piece" latch is necessary. The bay thinks there is a device there and there isn't. The POST (Power On Self Test) program won't allow it to startup if a device is missing.

Jun 18, 2008 | Gateway MT3705 Notebook

1 Answer

Camera not staying on.


Well, not sure if I have a solution. What I did has worked so far. It seemed to me the problem had to be a battery connector because my camera did this when the batteries got low. Then it got to doing it all the time. So I removed the back of the camera, cleaned it and took off and re-installed the battery door. First remove the batteries and the card. There are 8 screws, two on each side. The side with the card, you will have to open the card door to get to those two screws. Be sure to keep the screws separate because they are different sizes. Once the screws are removed, you can take off the back. Be care because there is a ribbon and a wire going from the camera board to the LCD on the back. Mine came off rather easily. I also removed the battery door. We stopped tearing apart at this time because I don't have the correct tools and really don't know what I was doing. We took a can of pressurized air and cleaned out the inside behind the board and around the battery connections. We put the camera back together. I haven't had any problems since and it has been about a week and I have been checking the working operation since. I think it has more to do with the battery door than the actual cleaning of the inside. While you have it open, you might as well clean it.

Apr 04, 2008 | Olympus SP-500 UZ Digital Camera

1 Answer

Red and Blue Shadows


There is no alignment of the lens because the optical lens is fixed. If he removed the lcd panels then there may be a problem. You may want to check to make sure there is nothing on top of the optical lens or the mirror inside the mirror block assy wasn't damaged. If he damged the optical block or lcd panels then an optical block may need to be replaced. Very costly. Good Luck

Sep 18, 2007 | Sony KDF-E55A20 55 in. LCD Television

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Alun Cox

Level 3 Expert

2678 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...