Question about Tyan Transport TA26 Server

1 Answer

I have a Tyan Transport TA26 that I cannot get any power too

Tyan Transport TA 26 cannot get any power to the main loop.

Is there a null or on/off power line controlling the main power supply or a fuse?

I do get minor power for leds, just not to the power switch or drive motors.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 40 Answers
Re: I have a Tyan Transport TA26 that I cannot get any...

No fuses.. try clearing the bios first

next do you get no boot... if so check if the MB is grounded out in the chassis...

also test the system out of the chassis...

pull the power supply and mb out and set on cardboard for testing

this should verify your power supply and MB

else stop and trash the MB for a new one... ebay possibly has a replacement cheap

Posted on Sep 28, 2009

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I cannot get the Dell PowerEdge 840 to recongize and of my HDD in the Raid array.. Trying to install the OS but tells my on HDD is detected

Then you need to get into the BIOS of the PERC RAID controller and inspect the state of the physical/logical volumes. Reboot the machine and watch for the prompt after the PERC5/6 RAID controller loads it's BIOS.

Considering this a null issue given the age, though...

Jan 21, 2014 | Dell PowerEdge 840 (becwmk1_2) Server

1 Answer

HP mediasmart EX470

Hello it depends on your current operating system.This could have happend after the update from MS yesterday.

It looks like a failed update.

Here is a link if you are running server 2008:

Good luck

Nov 13, 2012 | HP MediaSmart Server EX470 (GG795AA)

1 Answer

We have 3x V490's all responding the same way. Cannot power on any of them. Fault LED comes on when pushing the power on button. Do we have 3 dead units? Can you suggest anything else to look for?

Honestly... This issue is far too old to consider. I'm guessing it's a null issue at this point.

Otherwise... I would have said:
Where is this fault LED located on the chassis? Are you looking at the FRONT or the REAR?

Have you looked at the power supplies located on the rear of the chassis to see if their status LED shows a failure?

What have you done to troubleshoot this yourself?

Considering this "Closed - Too Old."

Jul 26, 2011 | Sun Fire V490 Server

1 Answer

PC will not turn on blinking green light on power supply

The green light on power is blinking, it means power supply working in main power and the main supply not constant that time after constant the green light, then turn on the PC.


Aug 13, 2009 | Intel SR1350-E Server Chassis...

1 Answer

ATI ES1000 RN50 WinXP Driver

Apr 02, 2009 | IBM Computer Servers

1 Answer

Booting problem

Did you replace the RAM and try if still persists then there could be problem with the RAM.

Dec 16, 2008 | Tyan Transport GT24 (B2891G24S4LC) Server

1 Answer

No video at all

try first with one cpu and only one stick of memory in socket zero

if the video does not come on... try next to reset the bios .. clear the settings... it may be setup to search for a pci or pci-e video card in the bios

next try to test the wattage being pulled into the system at boot... should be over 200watts.. may indicate a power issure

are there any beep codes ... post codes or ... is there a single beep tone during power on to verify the motherboard is functional and checks out fine at self start...

Aug 22, 2008 | Tyan Transport TA26 Server

2 Answers

Unkown SCSI Problem

Hi Fatoil ,

Have you tried another SCSI port , another SCSI card , another SCSI drive , swopping if it is card problem or drive or both problem ?.

If you have a spare SCSI hd , plug it in to same port and see if it works . Swop to another port and see if the spare SCSI hd works. Swop to another SCSI card and see if spare SCSI hd works.

All this elimination will narrow down the problem .
SCSI cards are not expensive ,.
old working SCSI hds don't cost you anything if you have them.
Sending out the server for servicing will cost you.
I presume you don't have a maintenance contract for this server .
If you have , get them down to settle it .
If you don't , after you settle this matter , make sure you get a maintenance contract for all your critical servers / equipment.

Maint Contracts seem expensive when nothing breaks down. However , when they do , it makes every worry go away.

Good luck,

May 26, 2008 | HP CC3310 (a9863a) Server

1 Answer

Tyan S3992 MOBO with scsi drives and tape drive

Only if your BIOS supports booting off the particular device. You could also try to swtich the two PCI slots. Put the tape drive controller in the 1st slot,and the SCSI controller in the 2nd slot.

Which tape drive is it? Is there a firmware update for the BIOS for that PCI controller? I would perhaps contact the vendor of the tape drive/controller

Feb 23, 2008 | Computer Servers

1 Answer

HP Compaq ProLiant ML110 G4 Server Problem

how to load HP Compaq ProLiant ML110 with windows 2003 server cd

Oct 25, 2007 | HP Compaq ProLiant ML110 G4 Server

Not finding what you are looking for?
Tyan Transport TA26 Server Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tyan Computer Servers Experts


Level 3 Expert

5660 Answers


Level 3 Expert

18259 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Tyan Computer Server Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides