Question about Dryers

1 Answer

Kenmoreoasis steam model 110.c6807(2801)power on,wont start tested thermal fuse circuit good. other thing beside thermal fuse tested no circuit present. 1 1/2 " oval shaped.is this my problem?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 456 Answers

I don't know. please test the door closing switch. i found one that the door pin would not quite reach.

Posted on Aug 30, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
aasc
  • 1606 Answers

SOURCE: Whirlpool duet electric wil not heat

Remove 1 wire from the element . Your 220 V comes from ...110 motor , 110 control board . Check which wire is not getting 110 V , trace it and see which it comes from . That will tell you which one is defective .

Posted on Aug 01, 2009

  • 1527 Answers

SOURCE: whirlpool dryer wont start

hello theres a long pin that sits inside the door make sure it has not snaped off if thats ok then the trouble may be caused by the capacitor next to the motor white cyilnder with couple of wires coming off

regards
shaun

Posted on May 30, 2010

  • 54 Answers

SOURCE: I need a heat plate for a grand gourmet gas grill

http://www.grillstuff.com/gas-grill-burners/?cat=48 try here

Posted on Jun 07, 2010

  • 523 Answers

SOURCE: Kenmore Dryer - No Heat

110 comes from the motor 110 comes from the timer remove the wire that comes from the motor see if you have 110 if you do the timer is bad if not the motor is. even if the motor is turning its bad

Posted on Jun 08, 2010

  • 35 Answers

SOURCE: the blue is oval shape drawn upward on the bottom

YOU HAVE CONVERGENCE PROBLEM. you need to have an electronic technition replace convergence ics and related resistors and pico fuse. J.D.W.

Posted on Jun 25, 2010

Testimonial: "I REPLACED THE IC'S IT WORKS FINE. THANKS"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool Dryer IED4400SQ0 wont heat


Check your thermal fuse and the thermal cut-out fuse, two different fuses that can cause a dryer to run and not heat when open, or some dryers will not start when one of these has gotten too hot and opened....Usually caused by venting restriction of too much lint, common problem...........

A open operating thermostat or the high limit being open are also possible........;.

The other checks are live voltage checks, timer contacts, wiring, temp and internal motor switch......schematic is probably in back of control panel........
Takes some reading of a wiring diagram, understanding how to split the circuit ............Not for beginners.............Hope this helps...........do not forget to unplug dryer when doing anything on unit besides live voltage checks on circuits,,,,,,,,,,,,,,,

Mar 12, 2014 | Whirlpool Inglis IP8200 Dryer

1 Answer

Dryer has power wont start


Hello Dom - Being that you have narrow down some possibilities, here are a few simple troubleshooting tips that may help you get to the root cause:

1. Make sure the dryer is plugged into outlet, and plugged in correctly.

2. Is house fuse blown or circuit breaker tripped? Replace fuse or re-set circuit breaker.
3. Make sure that electrical circuit is not overloaded and correct. The dryer must be on a circuit by itself. Overloaded circuits can damage the dryer and possibly cause damage to home. I would recommend reaching out to a Licensed Electrician check to make sure it is on a circuit by itself.

4. Thermal limiter tripped or an internal problem with the dryer. A thermal limiter automatically turns off the motor (electric dryers only) in the unlikely event of an overheated situation.A service technician must replace the thermal limiter after correcting the fault.

If these assessment measures prove to be ineffective, I would strongly suggest contacting an authorized service technician who would be better able to assist you in the diagnosis and repair of your unit. You can often locate an experienced technician in your area by going to the manufacturer website.

Jun 19, 2013 | Frigidaire Dryers

1 Answer

I have a kenmore 70 series heavy duty 110 96573230. It doesn't heat up. Can't find where the thermal fuse. Where is it located? Do I need to unscrew the back?


Yes, you need to take it all apart. ( Including the back.)
All of the things that can cause your problem are in the back and the bottom of your machine.
There are actually about 3 to 7 things that can cause "no heat".
Not only the "thermal fuse", but also the heating element, and any of the "overheat thermostat switches" can have failed, beside the possibility there is a wire has burned in two.
You will need a testing instrument like a multi-meter or a volt-ohm meter to check all these out.
Be blessed.

Mar 22, 2013 | Dryers

1 Answer

Wed6400sbo dryer wouldnt heat now start button wont work


check thermal fuse. Testing a thermal fuse

Note: Disconnect the power source to your dryer before you conduct this or any other test. Either unplug the unit from the wall outlet, remove the appropriate fuse from the fuse box, or flip the appropriate breaker in the circuit breaker panel. Testing a dryer's thermal fuse is much like testing its thermostats. Follow these steps to replace your dryer's thermal fuse.
The wires leading to the thermal fuse are connected using metal slip on connectors. Remove the wires by pulling on the connectors, and not the wires themselves. It may be a good idea to use a pair of needle nosed pliers to help you.
Set your multimeter to the R X 1 setting. Take each of your meter's probes and touch one to each terminal. You are testing for continuity, and you should receive a reading of either zero or infinity. At room temperature, testing the thermal fuse should produce a reading of zero. But if a thermostat is tested when it is heated to its limit, a reading of infinity should be produced. We strongly recommend that you test your thermostat at room temperature.
If the test you conduct with your thermostat does not produce these results, then you should replace the component.

Dec 09, 2011 | Whirlpool Dryers

1 Answer

The dryer wont heat up it turns fine just not heating up


Hi.

First try disconnecting power for few minutes (trip circuit breaker or disconnect power cord. Check and eventually replace the thermal fuse (or the thermal cutoff). If that does not get rid of the problem, then more parts will need testing and eventually replacement.

The door latch can be tested jumping its terminals. There are more thermostats in the heating assembly that must also be tested. More details on the repair procedure depend on the type and model of applaince in question.

Try replacing thermal fuse first.

To find parts and diagrams, try entering the model number on one of two websites in this link.

Regards.

Ginko.

Nov 29, 2010 | Dryers

1 Answer

Kenmore elite, model 110 60952990,stopped working after I tried to dry a pair of sneekers. It doesn't do anything when the power butten is pushed. Thank you.


The thermal fuse (part number 3390719) is blown causing the motor not to run. This thermal fuse is located on the blower housing beside the thermistor (part number 8577274) and it is wired in series with the motor thereby cutting power to the motor when it fails. The failure of the thermal fuse is due the failed thermistor; these requires both the thermal fuse and the thermistor to be replace.

Access to the thermal fuse and the thermistor for replacement or testing requires the removal of the lower front access panel which is secured to the front panel by two retaining clips positioned about three inches away from the sides. Pry the clips to release it and remove the lower front access panel. The thermal fuse and the thermistor can now be accessed.

Using a volt-ohmmeter, check the continuity of the thermal fuse which is to the left of the thermistor. Replace the thermal fuse if it reads open together with the thermistor.

Remove the mounting screws and mount the new parts in place. Disconnect the wires from the old failed parts and connect it to the corresponding component. Reinstall the lower front access panel back into position.

Apr 22, 2010 | Kenmore 63942 Dryer

1 Answer

Motor wont start,control circuit good fuses, ols ok motor megs good,how would I test klixon temp sensor that is wired into motor?


Power off. Unhook wires to thermal overload. use an ohmmeter or continuity tester to check it. It should have continuity or read very low resistance (<1 ohm usually)

Mar 06, 2010 | Air Tools & Compressors

1 Answer

Kenmore dryer 110-86094110 wont heat. Heating


Hi, Check all the thernostats and the thermal fuse for continuity. They should all show a closed circuit. If any of them are open, it will need replaced. It is usuallly the thermostat on the top side of the element housing.
I hope this helps you. If I can assist you further, please let me know.

Vic

Jun 28, 2009 | Dryers

1 Answer

Whirlpool dryer model LEB6000PQ0 its not heating up anymore''it starts it turns but the clothes dont dry its only 2 yrs old.


check your breaker first.A dryer will run on 110 but wont heat.if not breaker it could be your thermal fuse or element.the thermal fuse is located on element cage,unplug machine and test for continuity to your thermal cut off fuse which will be the top one on cage and check continuity to element.

Mar 08, 2009 | Whirlpool Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Brad Brown

Level 3 Expert

18072 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...