Question about NetGear WGR614 Wireless Router

3 Answers

How do i reset my router - NetGear WGR614 Wireless Router

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,272 Answers

HI, Follow the steps below to reset the router:

At the back of the router you will find a small tiny hole (which has a small button inside it). Press the button with the help of a paper clip. and hold it down for 30 seconds. After 30 seconds, please release the button and power off the device for 5 seconds.
I hope this information allows you to resolve this issue.

If I have helped you, please help me, and rate this suggestion the highest FixYa rating. If you cannot rate this post with the highest rating, then please comment to this post and I will try to help you further.

Regards
Anand

Posted on Sep 13, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 32 Answers

There should be a very small hole on the back of the router, stick a paper clip into the hole until it presses a button on the inside. Hold the button down for about 10 seconds and the lights should flash, the router will reset, and it will be back to factory defaults.

Posted on Sep 13, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 35 Answers

To hard reset the router:

- locate the factory reset button located on the back of the router, between the antenna and the ethernet jack
- with the power on, press and hold the button
- the power light should turn off, then after about 10 seconds, it should turn back on
- release the button and wait about 1 minute for the router to reset

You can also soft reset the router by logging into the administration panel and selecting "Erase" under the "Settings Backup" menu.

Posted on Sep 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

5 Answers

How to reset a belkin router


There are two basic ways to get This issue fixed Please follow as you like

A- Login and Change the Belkin router password -

If you Forgot the Belkin wireless password In this you don't need to reset the router to default settings.

Step 1 If you have Belkin router and want to Know the password first look at the back of your Belkin WiFi router there will be user name and password.

Step 2 You can also login in your router and Get to Know the Belkin router password.

Step 3 Connect the computer or laptop with router using a cable.

Step 4 Type 192.168.2.1 on the very top of your browser (URL box ).
For more Details kindly visit
How To Reset password on Belkin router Belkin password Reset Help
Good luck......

Jan 08, 2013 | Belkin Wireless Surf Router (F7D2301)

5 Answers

Can i reset the router back to the default setting





  1. Locate the reset hole on the router. The button will be on the back or side of the router.


routerreset4.jpg


  1. Leave the router powered on.
  2. Use a paperclip (or similar) to press and hold in the reset button for 10 seconds.
  3. Remove the paperclip.
  4. Wait approximately one minute for the router to restart.

May 10, 2011 | Belkin F5D8236-4 Router

1 Answer

Setting up wireless password


The router can be set to factory default by performing either of these two steps:

Resetting the Router Using the Reset Button
Resetting the Router Using the Web-Based Setup Page

NOTE: Pressing the Reset button on the back of the router for 30 seconds will reset your router to its factory default settings. All of the settings of the router will then be erased and the router's IP address will become 192.168.1.1.

To perform a hardware reset on your Linksys router, follow these steps:
Resetting the Router Using the Reset Button
Step 1:
Take note of the current settings of the router before resetting.
Step 2:
Press and hold the Reset button of the router for 30 seconds.

3798-001.png

Figure 1: Location of the Reset button on a Linksys BEFW11S4 router.
NOTE: The image may vary depending on the model number of the Linksys device.

4030-022.png

Figure 2: Location of the Reset button on a Linksys WRT54GX router.

4030-024.png

Figure 3: Location of the Reset button on a Linksys WRT54GC router.
NOTE: If the image of your router looks different from the ones shown above, consult your router documentation.
Step 3:
If the normal reset does not work, try to press and hold the Reset button for three seconds. The Ethernet light should go OFF then back ON. Unplug and re-plug the router's power adapter while pressing the Reset button. Keep holding the reset until the power light stops blinking.
NOTE: The router must be powered ON when you press the Reset button.
To reset the router via its web-based setup page, follow the steps below.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router's web-based setup page. For instructions, click here.
NOTE: To learn how to access the router's web-based setup page using a Mac computer, click here.
Step 2:
When the router's web-based setup page appears, click Administration then click on Factory Defaults.

kb4008-004_en.png NOTE: If the screen on your router's web-based setup page looks different, click here.
Step 3:
Click on Restore Factory Defaults and select Yes.

kb4008-005_en.png Step 4:
Click OK.

kb4008-006_en.png


Related Articles:

Accessing the Router's Web-Based Setup Page
Setting-Up a Router with Cable Internet Service
Setting-Up a Linksys Router Using DSL Internet
Changing the Linksys Router's Password

Nov 12, 2010 | Linksys Wireless-G WRT54G Router

2 Answers

Cannot remember log in info


The router can be set to factory default by performing either of these two steps:

Resetting the Router Using the Reset Button
Resetting the Router Using the Web-Based Setup Page

NOTE: Pressing the Reset button on the back of the router for 30 seconds will reset your router to its factory default settings. All of the settings of the router will then be erased and the router's IP address will become 192.168.1.1.

To perform a hardware reset on your Linksys router, follow these steps:
Resetting the Router Using the Reset Button
Step 1:
Take note of the current settings of the router before resetting.
Step 2:
Press and hold the Reset button of the router for 30 seconds.

3798-001.png

Figure 1: Location of the Reset button on a Linksys BEFW11S4 router.
NOTE: The image may vary depending on the model number of the Linksys device.

4030-022.png

Figure 2: Location of the Reset button on a Linksys WRT54GX router.

4030-024.png

Figure 3: Location of the Reset button on a Linksys WRT54GC router.
NOTE: If the image of your router looks different from the ones shown above, consult your router documentation.
Step 3:
If the normal reset does not work, try to press and hold the Reset button for three seconds. The Ethernet light should go OFF then back ON. Unplug and re-plug the router's power adapter while pressing the Reset button. Keep holding the reset until the power light stops blinking.
NOTE: The router must be powered ON when you press the Reset button.
To reset the router via its web-based setup page, follow the steps below.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router's web-based setup page. For instructions, click here.
NOTE: To learn how to access the router's web-based setup page using a Mac computer, click here.
Step 2:
When the router's web-based setup page appears, click Administration then click on Factory Defaults.

kb4008-004_en.png NOTE: If the screen on your router's web-based setup page looks different, click here.
Step 3:
Click on Restore Factory Defaults and select Yes.

kb4008-005_en.png Step 4:
Click OK.

kb4008-006_en.png


Related Articles:

Accessing the Router's Web-Based Setup Page
Setting-Up a Router with Cable Internet Service
Setting-Up a Linksys Router Using DSL Internet
Changing the Linksys Router's Password

Nov 12, 2010 | Linksys WRT54G2 Wireless Router

1 Answer

Cant log on to router


If you have forgotten your router's password, please follow the instructions below to resolve your issue.

The router can be set to factory default by pressing the Reset button of the router and resetting through the router's web-based setup page. Pressing the Reset button on the back of the router for 30 seconds will reset your router to its factory default settings. Any settings on the router will be erased and the router's IP address will become "192.168.1.1," the username is still blank, and the password will be "admin."

To perform a hardware reset on your Linksys router follow the steps below.
Resetting the Router Using the Reset Button
Step 1:
Take note of the current settings of the device before resetting.
Step 2:
Press the Reset button of the router for 30 seconds.

3798-001.png Figure 1: Location of the Reset button of a Linksys BEFW11S4 router.
NOTE: If your router does not look like this, refer to the other images below:
4030-022.png Figure 2: Location of the Reset button of a Linksys WRT54GX router.
4030-024.png Figure 3: Location of the Reset button of a Linksys WRT54GC router.
NOTE: If the image of your router is different from the ones shown above, please consult your router documentation.
Step 3:
If the normal reset does not work, unplug then plug back the router's power adapter while pressing the Reset button.
To reset the router via its web-based setup page, follow the steps below.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router's web-based setup page. For instructions, click here.
NOTE: If you are using Mac to access the router's web-based setup page, click here.
Step 2:
When the router's web-based setup page appears, click Administration then Factory Defaults.
4008-003.png NOTE: If the screen on your router's web-based setup page looks different, click here.
Step 3:
Look for Restore Factory Defaults and select Yes.
4008-005.png Step 4:
Click 4268-009.png.

Nov 11, 2010 | D-Link DI 514 Wireless Router (DI-514)

1 Answer

The Cisco System logo just stays orange, I attempted to repair on my lap top but it won't let me repair.


The router can be set to factory default by performing either of these two steps:

Resetting the Router Using the Reset Button
Resetting the Router Using the Web-Based Setup Page

NOTE: Pressing the Reset button on the back of the router for 30 seconds will reset your router to its factory default settings. All of the settings of the router will then be erased and the router's IP address will become 192.168.1.1.

To perform a hardware reset on your Linksys router, follow these steps:
Resetting the Router Using the Reset Button
Step 1:
Take note of the current settings of the router before resetting.
Step 2:
Press and hold the Reset button of the router for 30 seconds.

3798-001.png

Figure 1: Location of the Reset button on a Linksys BEFW11S4 router.
NOTE: The image may vary depending on the model number of the Linksys device.

4030-022.png

Figure 2: Location of the Reset button on a Linksys WRT54GX router.

4030-024.png

Figure 3: Location of the Reset button on a Linksys WRT54GC router.
NOTE: If the image of your router looks different from the ones shown above, consult your router documentation.
Step 3:
If the normal reset does not work, try to press and hold the Reset button for three seconds. The Ethernet light should go OFF then back ON. Unplug and re-plug the router's power adapter while pressing the Reset button. Keep holding the reset until the power light stops blinking.
NOTE: The router must be powered ON when you press the Reset button.
To reset the router via its web-based setup page, follow the steps below.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router's web-based setup page. For instructions, click here.
NOTE: To learn how to access the router's web-based setup page using a Mac computer, click here.
Step 2:
When the router's web-based setup page appears, click Administration then click on Factory Defaults.

kb4008-004_en.png NOTE: If the screen on your router's web-based setup page looks different, click here.
Step 3:
Click on Restore Factory Defaults and select Yes.

kb4008-005_en.png Step 4:
Click OK.

kb4008-006_en.png


Related Articles:

Accessing the Router's Web-Based Setup Page
Setting-Up a Router with Cable Internet Service
Setting-Up a Linksys Router Using DSL Internet
Changing the Linksys Router's Password

Nov 09, 2010 | Linksys Wireless-G WRT54GS Router...

1 Answer

When my pc starts I get an error message concerning something missing in the dynamic link library. How do i fix this?


Try:
Resetting the Linksys Router to Factory Default

The router can be set to factory default by performing either of these two steps:

Resetting the Router Using the Reset Button
Resetting the Router Using the Web-Based Setup Page

NOTE: Pressing the Reset button on the back of the router for 30 seconds will reset your router to its factory default settings. All of the settings of the router will then be erased and the router's IP address will become 192.168.1.1.

To perform a hardware reset on your Linksys router, follow these steps:
Resetting the Router Using the Reset Button
Step 1:
Take note of the current settings of the router before resetting.
Step 2:
Press and hold the Reset button of the router for 30 seconds.

3798-001.png

Figure 1: Location of the Reset button on a Linksys BEFW11S4 router.
NOTE: The image may vary depending on the model number of the Linksys device.

4030-022.png

Figure 2: Location of the Reset button on a Linksys WRT54GX router.

4030-024.png

Figure 3: Location of the Reset button on a Linksys WRT54GC router.
NOTE: If the image of your router looks different from the ones shown above, consult your router documentation.
Step 3:
If the normal reset does not work, try to press and hold the Reset button for three seconds. The Ethernet light should go OFF then back ON. Unplug and re-plug the router's power adapter while pressing the Reset button. Keep holding the reset until the power light stops blinking.
NOTE: The router must be powered ON when you press the Reset button.
To reset the router via its web-based setup page, follow the steps below.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router's web-based setup page. For instructions, click here.
NOTE: To learn how to access the router's web-based setup page using a Mac computer, click here.
Step 2:
When the router's web-based setup page appears, click Administration then click on Factory Defaults.

kb4008-004_en.png NOTE: If the screen on your router's web-based setup page looks different, click here.
Step 3:
Click on Restore Factory Defaults and select Yes.

kb4008-005_en.png Step 4:
Click OK.

kb4008-006_en.png


Related Articles:

Accessing the Router's Web-Based Setup Page
Setting-Up a Router with Cable Internet Service
Setting-Up a Linksys Router Using DSL Internet
Changing the Linksys Router's Password

Nov 08, 2010 | Linksys Wireless-G WRT54G Router

2 Answers

How reset passsword.? router


Dear arliwave

It is easy to Reset Router than to locate its User name and password,
To reset your router, first of all switch on your router and press its reset button for 10 seconds. While with pressed reset button switch off power of router than after 5 seconds release the reset button. Now your router is reset to its default position.
At default its user name and password are " admin " .
For browsing to router site type http://192.168.1.1 or http://192.168.2.1 in your browser address bar.Enter by using admin as user name and password.

Thanks for sharing your problem with Fix Ya Family

Jul 29, 2009

Jul 11, 2009 | Zhone (6218-I2-200) Router

1 Answer

Linksys Group LIWRT160N Ultra RangePlus Wireless-N Broadband Router say's password is not enough characters, however I am using the right password. Why can't I set up this Window's computer?


Okay,i only option is to reset the router to its factory settings.
Please follow the steps to reset the router.
The router can be set to factory default by pressing the Reset button of the router and resetting through the router’s web-based setup page. Pressing the Reset button on the back of the router for 30 seconds will reset your router to its factory default settings. Any settings on the router will be erased and the router’s IP address will become “192.168.1.1,” the username is still blank, and the password will be “admin.”
To perform a hardware reset on your Linksys router follow the steps below.
Step 1:
Take note of the current settings of the device before resetting.
Step 2:
Press the Reset button of the router for 30 seconds.
Step 3:
If the normal reset does not work, unplug then plug back the router's power adapter while pressing the Reset button.
To reset the router via its web-based setup page, follow the steps below.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router’s web-based setup page. .
NOTE: If you are using Mac to access the router’s web-based setup page,
Step 2:
When the router’s web-based setup page appears, click Administration then Factory Defaults.
Step 3:
Look for Restore Factory Defaults and select Yes.
Step 4:
Click 4268-009.png

May 18, 2009 | 2wire (1000-100016-002) Wireless Adapter

7 Answers

Forgot my belkin router password is there a way to reset it?


here you go, from Belkin's website

Reset the router to factory default Resolution With the router powered on, use a small thin object to press and hold the reset button for exactly seven seconds. The router lights will flash and this will restore the router to factory default. Connect your computer to one of the routers lan ports with an etherent cable. Open your web browser and navigate to 192.168.2.1. This should show the router status page with the default settings. SummaryThis article describes how to reset the router to factory default More InfoThis article assumes you cannot access the routers web interface.

Jan 26, 2009 | Computers & Internet

Not finding what you are looking for?
NetGear WGR614 Wireless Router Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top NetGear Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18408 Answers

Are you a NetGear Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...