Question about HP OfficeJet Pro K8600 Printer

1 Answer

Paper tray full lights still flashing empty - HP OfficeJet Pro K8600 Printer

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 54 Answers

Visit the below web link and follow the instructions provided in the document to resolve your issue.

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01289436&cc=us&lc=en&dlc=en&product=3434447

Posted on Sep 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HP 2200D Amber light keeps flashing! ..and nothing else


Hi,

Following are the reasons and its solution for amber light keeps flashing:

1. Toner have been empty.
Sol : Refill you toner.
2. Printer's paper tray do not close properly or paper in not in the tray.
Sol : Close the paper tray properly and keep some papers in the tray.
3. Any door of printer is open or not properly close.
Sol. : Check all the doors that is close properly or not.

If problem is still remaining then contact a professional to repair this printer.

Regards

Ashly

Feb 25, 2010 | HP LaserJet 2200D Printer

1 Answer

The traingle is flashing orange the rest not flashing. the printer does not print


In the Attention state, the Attention light is blinking and the Go and Ready lights are off. This state can be reached in the following circumstances:

● Paper tray is empty
● Door open
● Toner Cartridge Missing
● Paper jam/ Tray Misfeed

Pressing Go attempts to reset after a jam is cleared or is ignored in the other error cases. It may be necessary to clear the error manually and press Go or close the top cover. If the error still persists, the device will return to the Attention state.

Note
The LJ1010 product series does not have paper out sensors. When the printer is in an Attention state because the paper tray is empty, the user must reload paper and press Go.

Nov 13, 2009 | HP LaserJet 1010 Printer

2 Answers

Kyocera fS-920KX. Not printing


There are actually some certain meaning on the red light and green light showing different information to user. The summaries are:
1) Green On, Red Off = Printer Ready.
2) Green Fast-Flashing, Red Fast-Flashing = Printer warm up.
3) Green Fast-Flashing, Red Off = Printer off-line.
4) Green Slow-Flashing, Red Off = Processing Data.
5) Green Off, Red On = Cover Opened, Toner Empty or Developer Unit / Drum unit missing.
6) Green Off, Red Fast-Flashing = Paper Jam or waiting for jam reset.
7) Green Off, Red Slow-Flashing = Paper Empty or Paper tray is not inserted.
8) Green Off, Red Off = Printer power is off.
9) Green Very-Slow-Flashing, Red Off = Printer in sleep mode.
10) Green (any condition above), Red Slow-Flashing = Toner low or paper empty.

So what is your printer condition? Better know what is going on your printer so can solve the problem

YBC (/\)

Jun 01, 2009 | Kyocera FS-920 Laser Printer

2 Answers

Have replaced the ink cartridge to a full one. The system is still saying that it is nearly empty. Plus, the light is flashing.


you have to reinstall the printer as you first purchased it,realign it the whole bit.but most of these priters figure you change both at once but most people dont so the printer thinks its still empty.so take both cartridges out while printer is on ,shut it off count to 10,turn it back on.at this time it should prompt you to do the steps,follow them everything should be good.hope i helped

May 01, 2009 | Canon PIXMA iP4200 InkJet Photo Printer

1 Answer

Message keeps paper tray is full and it is full.


pull cassette out and look inside the cassette bay on the left side. there is a white gear that lifts up your paper. that might have come unseated. make sure its seated in right by pushing it back in. last but not least, make sure you don't have your rear paper stopper in cassette pushing paper too hard against the front of cassette preventing paper from raising up.

Mar 09, 2009 | Brother MFC-8460N All-In-One Printer

1 Answer

Paper tray is full and the paper light keeps flashing.


First check the machine for paper jams. If not, remove the paper from the paper tray and reinstall it. Then try to print from the MP tray.If this works, check paper size settings on the printer driver, or the small black arm which hangs down next to the paper pick up roller, and is the paper sensor.

Feb 09, 2009 | Brother HL 5040 Laser Printer

1 Answer

The paper light flashes but there is paper in the machine.


there is a paper sensor in the paper tray , it will detect where paper is present or tray is empty. may dust cover the sensor, clean the dust on sensor and check where the sensor is working or not

Dec 23, 2008 | HP DeskJet 895cse InkJet Printer

1 Answer

Error msg: paper jam or empty paper cassette when it is full


Click on the 'feed switch' on the front control panel- it might be feeding from the invisible drawer underneath and it might be empty. There is a light which will indicate which source it is feeding from.

Nov 27, 2008 | Canon PIXMA MP830 All-In-One InkJet...

1 Answer

CANT PRINT, IT SAYS PAPER EMPTY & IS NOT. RED LIGHT FLASHING


there is a little sensor flag which you probably knocked out of place. Remove the tray to gain access (plastic guides have a little stop. Just use a small flat blade screw driver and gently pry between steel guide and plastic guide to create a little more gap so the cassette tray comes off the guides completely.
Next, look in there and you will see a sensor flat which is supposed to dangle freely to make contact with the paper. It is a paper full sensor flag. If it isn't broke, you should be able to clip it back in its saddles.

Nov 26, 2008 | Toshiba DP125F All-In-One Laser Printer

Not finding what you are looking for?
HP OfficeJet Pro K8600 Printer Logo

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...