Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Error code showing error code f 7

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 3,230 Answers
Re: error code

Hi there, F7 = motor fault. New motor brushes fixed it. This error code will come up if the motor fails to turn on demand at any point in a program, be it filling, in a wash cycle, or spinning. Thanks

Posted on Jun 06, 2009

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Error code f25 replaced inlet thermador

call a repairman we do not know what you have .

Mar 16, 2016 | Washing Machines

1 Answer

LG front loading washing machine Direct Drive 7 3.5KG Trouble shooting Error OE

go to, enter your model number and manual will show error codes and fixed for some including OE

Aug 29, 2015 | LG Washing Machines

1 Answer

My 140express hasn't spun properly an is showing the sign F21

It sounds like a problem with the control board. To reset the codes follow these instructions:

1. Close the door.

2. Turn the knob to 6 o'clock position.

3. Wait 2 seconds.

The start/pause should begin flashing.

4. Press and hold the spin button.

5. Turn the knob to 7 o'clock position.

Wait 2 seconds.

6. Release the button.

7. Turn the knob to off.

This should erase the error code and get you running again.

If the error code returns, you have a problem with the motor, wiring or main control.

If the machine won't go into diagnostics to erase the error code, it would suggest a faulty control board.

Try it several times to see if you get it reset.

Hope this helps.

Jan 03, 2015 | Bosch Washing Machines

2 Answers

Hi, How Can I Reset error in my wash machine Bosch

You can reset the error code by the follow steps.
Turn the knob to the off or reset position, 12 o'clock.
Turn the knob to the 6 o'clock position.
Press and hold the spin button and while holding the spin button turn the knob to the 7 o'clock position.
Continue holding the spin button for about 5 seconds then release the spin button and now turn the knob to off
When your turn it back on it should have cleared the error code.

Sep 26, 2013 | Bosch Washing Machines

1 Answer

Machine stopped mid cycle and green light flashing under green start button

Many modern washing machines display error codes if they detect a fault, but not all washing machines display a readable error code, some indicate an error by flashing, or lighting some of the lights.

Hotpoint, Indesit, Zanussi error codes

Hotpoint, Indesit washing machines and Zanussi washing machines are some common appliances that display coded error codes. On their more expensive models, they display readable error codes but basic models (without digital displays) use flashing lights to convey the error fault code.

If your washing machine malfunctions and you can see some of the lights flashing, or one or more option lights have lit up, then make a note of which lights are flashing and which option lights are lit. NOTE: the error code list engineers have only shows the option lights by number and not by name. Therefore you need to report the lights as LED 1 and 3, or 2 and 4 etc. and NOT "delay timer" and "extra rinse". Count the lights from the left (or from the top if in a column) and report as "led 1 and 3" etc.

No Option lights?

With basic washing machines that have no option indicator lights, count the number of flashes. For example, the door locked indicator may flash 7 times, pause, and flash another 7 times in a constant cycle which would indicate error code 7.

This information is vital, and needs mentioning when reporting a fault.

Jan 18, 2011 | Zanussi FJS1225W Front Load Washer

1 Answer

Problem with the Samsung Washing Machines The machine keeps coming up with the message HEI 10x

Here is a list of errors for your machine.

I hope they help you.


When an error occurs, the alarm noise will sound and the error code displayed in the program window. Listed below is a series of error codes you may or may not see for your model of Samsng Washing Machine. The errors are shown as blinking in O.5 second intervals until the error status has cleared. In this case, all the driving devices are turned off until the error is cleared.

1. WATER SUPPLY ERROR - Display shows 4E.

Water Supply Error occurs when water level frequency does not show changes more than 100Hz or water is not supplied up to the preset water level after 10 Minutes or more at the time of initial water supply. The error status can be cleared by turning the POWER switch OFF and back ON.

2. WATER DRAIN ERROR - Display shows 5E.

5E is displayed if the water level frequency detected is 25 KHz or less in the initial phase of the UNB -detecting cycle. The Water Drain error can be cleared by turning POWER SW OFF and back ON.

3. OVER-FLOW ERROR - Display shows oE.

Over-Flow error occurs when the water level is too high. It can be cleared by turning POWER switch OFF. Water is drained prior to POWER switch OFF. The tub is drained for 2 minutes if a frequency of more than 25 KHz is detected.

4. UNBALANCE ERROR - Display shows UE.

Laundry load is unbalanced, manually loosen any tangled laundry.

If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an UE error message will be shown in the display. Unbalance error is cleared by POWER switch OFF and back ON.

5. WATER HEATER ERROR - Display shows HE, HE1.

HE, HE1 is displayed if the water temperature rises by 7 C or more in 1 Min or by 2 C or less 20 Min after heating process has started. The error can be cleared by turning POWER switch OFF.


* Generated Frequency Signal of WATER LEVEL (WIL) SIW (KHz)

Normal Level = Abnormal W/L Frequency
Low Level = 30.00 Khz
High Level = 15.00 Khz

If the same signal is detected for more than 5 seconds, it is a PRESSURE SWITCH Error. When this error occurs the drain pump will operate for 3 min. and the display will show 1 E indicating a pressure switch error.


e.g. If the water temperature is 50 C or more, during a Delicate or Wool cycle.

At the time of initial water supply, if the water temperature is not appropriate, the display will show cE. This error can be cleared by POWER SWITCH OFF.

8. WATER LEAKAGE ERROR - Display shows 11 E.

Water Leakage error occurs when the water drains naturally, (by leakage) after the washing program starts.

9. THERMISTOR ERROR - Display shows tE

Nov 21, 2010 | Washing Machines

1 Answer

It flashes f o7 on my wie 127

hi sir, It seems that a common error code on Indesit washing machines is error code 7. This code can show itself as F 007 or with washing machines that have a rotating control dial the door lock light can flash in cycles of seven times.
This error code usually means, “heater relay stuck”.
The heater is switched on via a relay built into the main PCB. This relay is known to get jammed causing error code 7. In my experience this has usually meant a new PCB needed fitting and as the PCB comes without the main processor EEPROM chip one of those is needed also.
This repair is going to be expensive. I have heard anecdotally of engineers freeing off the jammed relay by giving it a firm tap. However, I would not expect such a repair to last as the chances are the relay would just get stuck again later on.
If a washing machine is still under the five-year parts warranty it would be cheaper to let the manufacture fit these parts but although the parts would be free the labour is going to be about £90.

kindly rate me..
thanks for using fixya..

Feb 12, 2010 | Indesit Washing Machines

1 Answer

Have error code of f 02 showing up on my duet. It is not finishing spin or drain cycle?

If the drain time exceeds eight minutes, the water valves are turned off
and “F/02” is flashed. Press PAUSE/CANCEL two times to clear the
NOTE: After four minutes the “Sud” error will be displayed, then four
minutes later the “F/02” error code will be displayed.
1. Check the drain hose and make sure it is not plugged
or kinked.
2. Unplug washer or disconnect power.
3. Check the electrical connections at the pump and
make sure the pump is running.
4. Check the drain pump filter for foreign objects.
5. Plug in washer or reconnect power.
6. If the above does not correct the problem, go to step 7.
7. Unplug washer or disconnect power.
8. Replace the pump.

Nov 18, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

LG Sense Clean DD error code "FE" front loader washer/dryer combo

my lg senseclean wash mashine shows the sign Cl on the display and the door cannot be open what does it mean?

Jan 03, 2009 | LG 4.0 Cu. Ft. 7-Cycle Front-Load Washer -...

3 Answers

Error code 7

The error code 7 is in fact a motor error.
The motor that drives the spin cycle has become faulty. The only solution now is to get an engineer in to fix it or get it sent away to get repaired.

Sep 08, 2008 | Haier XQG50-11 Front Load Washer / Dryer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

1,106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides