Hi I have a Daewoo tv approx 6 months old, it wont come on. The power light comes on but thats about it. When i press a channel via the remote it flahes green then goes back on red?? Please help. Regards

Here's how to scan for TV codes on your DIRECTV remote

1.Make sure your TV is turned on.

2.Slide the mode switch at top of remote to "TV".

3.Press and hold the MUTE button. This is located above the number 1 button.

4.While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.

5.Then enter 991, the green light on remote should flash twice.

5b. Press 1 again (it will flash twice again), then you press the power on button at the very top right.

6.Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.

*If you hit channel up very fast, you risk going past the code. Pressing channel down will back it up. I alway hit channel up very fast till the tv turns off, then back it up slowly till it comes back on.

7.When the TV powers off, press and release the SELECT button.

*Note: If the green light flashes three times before TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, however your TV may not be compatible with our remote control.

Hi.

Go to this link: remote codes

Fixya me on this...

I recently had the same issue with a 6 month old Panasonic...the Tech determined that a component on the main circuit board failed. I was lucky and it was fixed under warranty. Good luck!

The Sanyo codes appear to be 620, 801, 931 . Turn on the TV, press and hold Set-up until the light comes on and enter the three digit code. Check if the TV responds (volume, channel). If not try the next code.

To search all codes: turn on the TV, press and hold the Set-up button. Then press Channel + slowly but repeatedly until the channel changes. Press Enter (if you overshoot, press Channel - to before pressing enter.) To record the code, turn on the TV, press and hold Set-up, then press Set-up again and type 0-9 individually until the indicator light blinks. That is digit 1, repeat the search from 0-9 for the other two digits.

If your TV was released ~6 months before the remote was programmed or is newer than the remote, then the code you need may not be in the remote's programming. In that case, you need a newer remote, one of the remotes that is programmable (USB to a computer), or a remote specific to your TV (try remotes.com and search on the TV model - leave off the brand name).

I hope this helps.

Cindy Wells

How old are the remotes relative to the TV in question? If the remotes are older than the TV or were programmed within 6 months of this TV being released, then the code you need wasn't included in the remote's programming. In addition, unfortunately, many universal remotes do not work on combination TVs (with the DVD player and VCR built-in).

You can try to search through all the codes for the remote if your remotes have that feature. (On RCA remotes, turn on the TV, press and hold the Code Search button until the indicator light comes on, then press and release the TV button. Then press the On/Off button repeatedly until the TV turns off. Press Enter and see if the other functions of the remote work. If they do not, repeat the search. Then do the same but press the DVD and VCR buttons instead of the TV button.)

More likely you need a newer universal remote, a programmable (via computer USB) universal remote or a substitute remote from the manufacturer. See http://www.remotes.com/remotes/servlet/rs?a=gmi&uuid=12845952409830&smodel=TDC2075&brand_pn=SANSUI_TDC2075 for an exact substitute remote that will replace the original remote.

I hope this helps.

Cindy Wells

Heres where you need to go for the codes and programming procedures; 

http://www.comcast.com/corporate/customers/customer_support/remotes.html

Hi You have power supply problem.Please go to ebay and buy cheaper price: AKAI LCT3201TD POWER SUUPLY MLT169A REFURBISHED CHAINA Thanks

Press tv on the Sky remote

press and hold select and red until the led blinks twice
type in 0 0 6 0
press the power button, if the tv turns off then the press select and the remote should work all the tv functions.

If the tv does not turn off then press tv then the power button and keep doing this until the tv turns off, once it turns off press select and it should work.

If you have any problems let me know

Dazz

if u have a universal remote and none of the codes seem to work after trying all the codes and non still don t work follow these steps


1. make sure the power on the TV is turned on
2 press and hold code button until it flash twice
3 then press the TV mode button until the light flashes the press
4 power button until TV powers off

You will need to go to Sky's website and order a new remote if this doesn't work.

Press tv on the remote
press and hold Select and red until the remote LED blinks twice
type in 0 0 6 0
press power button on the remote, if the tv goes off press select and it should control all the tv functions.

if the tv does not go off press tv then power buttons on the remote and keep doing this until the tv goes off, then press select once the tv goes off.

Like I said earlier, if this doesn't work you will need to order a new/replacement remote via Sky's website then put the code listed above in.