Question about HP PSC 1210 All-In-One InkJet Printer

3 Answers

HP PSC will not print

I recently upgraded to Windows Vista and the printer was working fine. Just today, I cannot get it to print. The icon shows the document in que but it goes away after a few seconds and nothing shows to be printed. Any help would be appreciated.

Posted by on

  • 1 more comment 
  • Anonymous Dec 11, 2007

    Upgrated my computer to vista Hp 1210 xi willnot print

  • csimo1 Dec 18, 2007

    i cannot install

  • Anonymous Feb 13, 2008

    pint icon has question mark onit and wont print

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I am having the same problem as madmax61958 with the exact same printer. i tried what Silan said but it didnt work. In my device manager it seems to recognizes the printer but has a little question mark icon on it. What does the question mark mean?

Posted on Jan 11, 2008

  • ajp0980 Jan 11, 2008

    I found on the windows website that the hp psc 1200 series printers are not on the Windows Vista Hardware Compatibility List. However hp has on their website that these printers should work automatically as you connect them to your computer.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 1210 all in one printer looking for a driver for Window Vista.
When I ran XP it was okay.
Now with Window Vista I have a software problem.

Max

Posted on Jan 07, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 54 Answers

Click Start (windows) icon - Control Panel - Printers. Right click on the HP PSC icon. Set the printer as default printer. Right click on the printer icon and select Set as default. Right click on the printer icon - Select properties - Click on Ports tab - Change the port to USB virtual printer port. Click Apply and Ok. Try to print. If the issue did not resolve. Get back to me.

Posted on Dec 22, 2007

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windows 7


Hi

Kindly go through the below link it has the patch for your printer to work with Windows 7

http://www.softwarepatch.com/utilities/hp-psc.html

Let me know if this will help all the best

Regards

Nov 29, 2009 | HP PSC 2210 All-In-One InkJet Printer

1 Answer

I can scan, BUT I can't print. HP PSC 1500 windows 7


Go to control panel and check the printer status, Unplug the USB cable than right click on printer icon and click on delete. Once you do that make sure printer icon should be gone. Than restart the computer. Once computer is Up than connect the USB cable of printer and make sure while doing that , the printer should be powered on. After that printer icon will again reappear in contro panel.

Try printing, it should work

Jul 22, 2009 | HP PSC 1510 All-In-One InkJet Printer

1 Answer

Hp psc 1210v all-in-one printer, scanner, copier will not scan


CHECK BELOW OTHERWISE GO TO HP WEB SITE AND LOOK FOR THE DRIVER SUPPORT TO DOWNLOAD.


Scanning
Use one of the following three methods to scan a document. Method one: Scanning with Windows Photo Gallery
  1. Click the Windows (c01367376.gif ) icon.
  2. Click All Programs .
  3. Click Windows Photo Gallery .
  4. Click File , and then click Import From Scanner or Camera .
  5. Click Import .
  6. Click Scan .
Method two: Scanning with Windows Fax and Scanning
NOTE: This feature works only with Windows Vista Ultimate, Windows Vista Business, and Windows Vista Enterprise.
  1. Click the Windows (c01367376.gif ) icon.
  2. Click All Programs .
  3. Click Windows Fax and Scanning .
  4. Click New Scan .
  5. Click File , and then click Scan .
Method three: Scanning with Paint
  1. Click the Windows (c01367376.gif ) icon.
  2. Click All Programs .
  3. Click Accessories .
  4. Click Paint .
  5. Click File , and then click From Scanner or Camera .
  6. Click Scan .

Jan 13, 2009 | HP PSC 1210v All-In-One InkJet Printer

5 Answers

Hp psc 1215 wont scan with vista


s.gif s.gif

Introduction Some products do not have full scan functionality in Windows Vista. This is because full-featured Vista drivers are not available for all products, especially older products. However, the Windows Vista operating system installed on your computer includes a basic print driver. This driver allows you to scan an original and save it as an image using workaround methods. You cannot use the advanced scanning features that you might have used with your product before you installed Microsoft Windows Vista. Scanning an original and saving it as an image Follow these steps to scan an original document, and then save it as an image. Step one: Load the original Follow these instructions to load the original in the product.
  1. Raise the top cover of the product.
  2. Place your original print-side down on the glass.
    NOTE: The engraved diagram next to the scanner glass shows exactly where to place the document (usually on the right-front corner or the left-front corner).
  3. Close the scanner lid.
Step two: Workarounds for scanning an original and saving it to the computer Select one of the following three workaround methods to scan an original and save it as an image. Method one: Scan with Windows Photo Gallery
  1. Click the Windows (c01319360.gif ) icon.
  2. Click Programs .
  3. Click Windows Photo Gallery . The program opens in a new window.
  4. Click File , and then click Import from Camera or Scanner .
  5. Click Import .
  6. Click Scan .
Method two: Scan with Windows Fax and Scanning
NOTE: This feature and the following instructions work only with Vista Ultimate, Vista Business, and Vista Enterprise versions of Windows.
  1. Click the Windows (c01319360.gif ) icon.
  2. Click Programs .
  3. Click Windows Fax and Scan . The program opens in a new window.
  4. Click New Scan .
  5. Click File , and then click Scan .
Method three: Scan using Paint
  1. Click the Windows (c01319360.gif ) icon.
  2. Click Programs .
  3. Click Accessories .
  4. Click Paint . The program opens in a new window.
  5. On the Paint toolbar, click File , and then click From Scanner or Camera .
  6. Click Scan .

Nov 30, 2008 | HP PSC 1215 All-In-One InkJet Printer

2 Answers

Hp psc 1210 not working in vista - but diagnostic utility shows all ok - and prints test page


Here is the full-write up on the HP PSC1210. Read through this thoroughly to ensure that you follow all the steps to make it work in Vista, since there is no Vista native driver.

Hope this helps - remember to rate :)

Oct 02, 2008 | HP PSC 1210 All-In-One InkJet Printer

1 Answer

Cannot use my HP printer 1610v


Go to the printer home page. They ususally have FAQ there and I believe you can also seek an answer through their home page,

Sep 22, 2008 | HP PSC 1610v All-in-One Printer

1 Answer

HP psc 2110 all-in-one wont print from internet


I'm assuming you went to the HP site and downloaded the Vista drivers??? Other than that try this:

  1. From Control Panel > printers... uninstall all printers.
  2. Unplug USB cable to printer and re-boot.
  3. Install Software.
  4. Plug USB cable back in.
Hope that fixes Ya...

Geno

Mar 26, 2008 | HP PSC 2110 Color Printer

7 Answers

HP PSC 1210 all-in-one Director does not work with VISTA


I've been fighting the same. Did some hunting on the HP and MS web sites. Found a "work around". Not what I wanted but at least I can scan. I think HP Director is gone for Vista users. :(

Scanning with Windows Photo Gallery
1. Click the Start ( ) icon.
2. Click All Programs .
3. Click Windows Photo Gallery .
4. Click File and then click Import From Scanner or Camera .
5. Click Import .
6. Click Scan .

Jan 16, 2008 | HP PSC 1210 All-In-One InkJet Printer

3 Answers

How do I Upgrade from Windows XP to Windows Vista


Neddybear, turn on your laptop, then plug a usb cable from it to the printer. Turn on the printer and the drivers should download automatically.

Dec 05, 2007 | HP PSC 1510 All-In-One InkJet Printer

Not finding what you are looking for?
HP PSC 1210 All-In-One InkJet Printer Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18426 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...