Question about Dishwashers

1 Answer

WATER IS NOT DRAINING DOES THE DUB500X-BO HAVE A PUMP FOR DISCHARGE?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 59 Answers

CHECK IF HOSE IS NOT KINKED, CHECK IF DRAINAGE IS NOT CLOGGED.YES IT HAS A DRAIN PUMP.

Posted on Sep 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone know how much it costs to fix a samsung dishwasher that shows e3 code? Is it a big fault or simple fix?


you may have a problem on the draining system. Previous cycle not fully drained and holding off the new cycle.
remove the drain line from its discharge position and hook up a 5 gal container for it to drain in ( maintaining the necessary height for the anti syphon loop )
Select programme 7 which should allow the drain pump to kick in straight away
You should be able to hear the pump running at the bottom of the machine and observe a discharge from the hose.
The chances are the pump needs removing and cleaning.
or - the drain line where the machine discharges is backing up and not allowing a free discharge.

Jun 11, 2016 | Samsung Dishwashers

1 Answer

Washer will not drain even after changing water pump


There is a drain pump that is separate from the main pumps on most kenmore elites. There is also a check valve that could be stuck open. 8 of 10 times, however, if the machine was working fine and is now not fully draining, this is due to a drain hose pluggage or kink somewhere between the drain pump and the discharge into the sink. I've seen grease totally block the discharge into the sink trap and cause this problem. This should be thoroughly checked and must be 100% clear for the dw to drain properly.

Apr 22, 2014 | Washing Machines

1 Answer

How to remove water pump ge front loader washing machine


Pretty simple operation...here's an overview of the component locations:

chris_in_ma_4.jpg
Remove the 3 screws at the bottom of the front panel. Lift panel out at the bottom and it should fall down. Discharge pump is on the right-hand side. Simply disconnect the hoses from: 1) the tub and from 2) the outbound discharge hose. Then remove all screws holding the pump in place. The electrical is a quick-connect adapter.

Save yourself a mess by draining the assembly first -- just follow the instructions for draining/cleaning the filter in the Use & Care manual

Jul 27, 2011 | General Electric WCVH6800J Front Load...

1 Answer

My saniflo pump turns on about every six hours or so on its own.what could be the ploblem?


Water pressure makes the unit kick on and off. Most likely somehow water is draining back into the pump. Check the flapper in the flush valve, inside the toilet tank and see if its leaking water into the bowl and from the bowl into the pump. Also, in the 90 degree discharge elbow there is a check valve with a rubber flapper that opens up to allow waste to pump out and it closes to prevent waste water from draining back into the pump. The check valve may be defective or it may be stuck open allowing waste water to drain back into the pump and is making the unit kick on and off by itself.

Apr 03, 2011 | Saniflo 002/005/007 Saniplus Toilet with...

2 Answers

My Kenmore dishwasher leaves water in the bottom of the dishwasher. Is that OK? I notice the water when I clean out the bottom tray.


Hi,


Here is a tip that I wrote that will help you with your dishwasher not draining problem...

Dishwasher Problems -
Water will not drain out

heatman101

Jan 18, 2011 | Kenmore Washing Machines

1 Answer

Sanipro xr is less than 6 months old been working fine but has recently become rather noisy. Sometimes goes off in the middle of the night for no reason.


Water pressure makes the unit kick on and off. Somehow water is draining back into the pump casing, check the flapper on the check valve inside the discharge elbow, it may not be closing properly or may be obstructed allowing waste water to drain back into the pump. Also check the flapper on the flush valve inside the toilet tank (water closet) the flapper may be leaking water into the bowl and from the bowl into the pump casing sitting behind. As far as making a loud noise, there could be a blockage on the drain pipe, blade or impeller. The discharge pipe may be loose, not clamped against the wall and is rattling against the wall when in use.

Jan 08, 2011 | Saniflo SaniPlus-Round SaniPlus Macerator...

1 Answer

The motor turns but does not push water


did you forget to open the valves on either side of the pump after draining and filling perhaps ?

Jan 01, 2011 | Waterway Spa Pump Executive 56 Frame 4hp...

1 Answer

Saniflow pump keeps comming on without flushing toilet


Water pressure makes the unit kick on and off. If it's turning on by itself then most likely somehow water is draining back into the pump. It could be leaking water from the toilet tank, to the bowl and from the bowl to the pump. Or the check valve inside the discharge elbow may not be closing all the way down and is allowing waste water to drain back into the pump creating enough water pressure that makes the pump kick on and off. Inspect the flapper on the flush valve and the check valve on the discharge elbow on top of the macerating pump.

Aug 22, 2010 | Saniflo 002/005/007 Saniplus Toilet with...

1 Answer

Saniflo keeps going off when not flushed


Water pressure makes the unit turn on and off. If it turning on by itself then could be water draining back into the pump. Water could be leaking from the check valve on the discharge elbow into the pump or from the toilet tank into the bowl. Inspect the flapper on the check valve and the flapper on the flush valve.

Aug 09, 2010 | Saniflo & Saniplus& Macerator Pump

1 Answer

Macerator keeps going off even when not flushed.


Water pressure makes the unit turn on and off. It will only activate on it's own when enough water pressure is present. Most likely it can be water leaking from the toilet tank into the bowl, and from the bowl into the pump. Or could also be that waste water is slowly draining back into the pump through the check valve on the discharge elbow, creating enough water pressure that it will make the unit kick on and off.

Aug 06, 2010 | Saniflo & Saniplus& Macerator Pump

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Brad Brown

Level 3 Expert

16614 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...