Question about Bosch HES 232 / HES 236 Electric Kitchen Range

1 Answer

Error message I was using the back right burner only and got a "error 120" message...I hit the off button and the beeping stopped and hasn't come back and I'm still using the burner. What does that message mean? There is nothing about it in the maunal.. thank you!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 126 Answers
Re: error message

I couldnt find it either sorry but dont worry about it unless it returns

Posted on Dec 10, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

F9 error message after power outage

The F9 is a door lock latch circuit problem, either the motor latch or the control/power supply board will need to be replaced.

Mar 22, 2008 | Jenn-Air JES8750 Electric Kitchen Range

1 Answer

Get an error "err surface burners off" when starting self-clean mode

I have the same problem with my GE Profile gas range. Every time I try to lock the touch panel (pressing and holding RANGE LOCKOUT), this message shows up. Every time this happens, the message goes away in a few seconds, but the touch panel never really locks. I didn't realize this wasn't the proper behavior until last night.
Last night, I did the same, but this time the "err turn burner off" message would not go away and there was an audible alarm beeping at once per couple seconds. I cycled the power by turning off the circuit breaker and back on, but every time the same message and alarm comes back.
When the err message is on, no gas is fed to the burners -- when I turn the dials, no gas come out from any of the burners. I guess this message is to alert the user that one or more of the burner dials are still in the open position and is telling the user to turn them off to the closed position.
Even though all four burner dials are in the fully off position, one of them was apparently not recognized by the sensor as being in the fully closed position. By turning this dial slightly in the clockwise direction just a little past the off position (even though it already appears to be in the fully off position) allows the sensor to recognize that it is now off. The error message and the alarm goes off and the panel then showed LOC, indicating that it has entered lockout mode. After that, I can unlock the panel by pressing the RANGE LOCKOUT button again.
So for me, the problem seems to be that the sensor for one of the dials was not registering that it was closed, and turning it a slight bit past off did the trick. The other three burners have no issue.

Jan 03, 2013 | GE Cafe CGS980S Kitchen Range

1 Answer

Frigidaire stove(smooth top -electric) all of sudden started to beep' constantly w/F1 flashing.Tried to reset - unsuccessful. Unplugged & waited an hour to plug back in & still beeping...

The F1 error code means a button on the touchpad is stuck,usually pushing clear/off will clear it. Since you have done that and it returns the touchpad needs to be replaced


Aug 11, 2011 | Frigidaire 30" Self-Cleaning Freestanding...

2 Answers

Hello, I was using the self-clean function of a Kenmore Rangr 790. It first showed an error code the it showed F30 and now it shows F10 error. It keeps beeping and won't shut off beeping. Do I need to...

Try turning it off at the breaker. It is way easier than pulling it out and unplugging it. Also, leave it powered off for at least 7 to 10 minutes. This sometimes resets the control board and stops the beeping. If the beeping starts up again you may need a new control board. At this point it is a good idea to call in a pro. Good Luck

Mar 14, 2011 | Kenmore 46702 / 46704 / 46709 Electric...

1 Answer

Whirlpool Accubake F2EO

F2E0 is shorted key pad. You will need to replace keypad if the power shut down and reset does not work.

Mar 09, 2010 | Kenmore 95002 / 95004 Electric Kitchen...

1 Answer

Kitchenaid YKGRT607HS6

F2:E0 is shorted keypad, and F2:E1 is no keypad connection, you need to replace the keypad.

You can find schematics and find replacements by entering model number here.

Dec 14, 2008 | KitchenAid KGRA806PSS Gas Kitchen Range

1 Answer

Tappen gas 4 burner about 10 years old with about 10 hrs total use time(basement stove)

Hi Carlsr,

The F1 error code description is an electronic oven control failure. To fix this error, you need to replace electronic oven control (also called EOC or clock).

Hope it helps.

Thank you for using FixYa.

Apr 13, 2008 | Tappan TGF320 Gas Kitchen Range

1 Answer

Maytag gemini f1-9 error

plug it back in and press the cancel button

Mar 31, 2008 | Maytag MER6772 Gemini Electric Kitchen...

3 Answers

Kenmore Elite Range door locked error message

Hold down the number three button until the LOC message disappears and then the door will open.

Dec 23, 2007 | Kitchen Ranges

Not finding what you are looking for?
Bosch HES 232 / HES 236 Electric Kitchen Range Logo

Related Topics:

915 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Kitchen Ranges Experts

William Miller
William Miller

Level 3 Expert

8795 Answers

Cindy Wells

Level 3 Expert

4719 Answers


Level 3 Expert

56797 Answers

Are you a Bosch Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides