Question about Televison & Video

Open Question

Goodmans k2110pf tv

Colour problem top right of screen colours not converging

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
techman
  • 3130 Answers

SOURCE: Convergence Problem?

The convergence IC most likly shorted, and burnt out the b+ feed resistor. There are two IC's inside this set to control the green red and blue convergence. They are most likly STK 392-###. The ### is another set of numbers that change depending on the model of the set. They each have three amps inside each one. You really should have both of the IC's replace with only original parts, as sub parts do not hold up and will not last as long as they should. Both IC's are soldered into place and if you decide to do this yourself, please be aware of the extemly high voltage inside of these puppys. there really are no user replaceable parts inside these sets unless you have solid state repair experience. Not only will yopu need the proper IC's, but you will have to find out what was burning. my best advice, Play it safe and call in a trained tech to assist you with this repair. The price should run someware between 300 to 450.00 to repair. Good Luck Please do not forget to rate this thread.

Posted on Dec 08, 2006

Ad
premtech
  • 934 Answers

SOURCE: colour problem on rear projection tv

This might be something really simple... In a large number of DPTV310 chassis, of which this TV is, the yoke connections where put in place with black electrical tape just below the retaining rings. Job is to loosen the rings, remove the tape and push the yoke back in place and tighten down retainer.. Be careful not to throw off the tilt of the yoke. The adhesive on the tape, over time, gets hot so many time it becomes slippery and allows the yoke to fall away from it's position dulling the look of the image (or focal length) causing the problem you're describing here... It also throws off the convergence - so in attempting to converge it just looks worse. Good Luck Bill

Posted on Jun 11, 2007

  • 2 Answers

SOURCE: Hitachi 43FDX01B (convergence) problem

hi i have same prob iv bin told its a convergence chip an thay r £150 ! thay go bout evry 6 years an its comon .. any way there coming 2 fix mine 2day so ill let u know if it sorts it out my mail is mjoutlaw@hotmail.co.uk thanx

Posted on Feb 01, 2008

  • 1 Answer

SOURCE: Plasma Tv 42PD580DTA, Black and white screen while viewing DVDs or Video

Hi there,
My sister-in-law has exactly the same problem and is a common one with this unit.
I've spoken to a technician who says that:
1. Hitachi are withdrawing from Australia and there are VERY limited service centres left
2. The problem is a chip on the main board and depending when the TV was made will determine whether the chip is a plu-in or soldered on to the main board - if it's the latter, you'll be up for a main board at around $400
3. He couldn't get the price of the plug-in chip because he couldn't get through to Hitachi.

Cheers

Dave M.

Posted on Apr 28, 2008

  • 20 Answers

SOURCE: overlapping words & rainbow colours (hc-p5252w samsung)

The biggest and most commen prob is the STK392-040 chips on the big heatsink and check the 3.9ohm resistors also the is a fuseable resisitor hidden under the heatsink dont forget to change also.

Posted on May 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have done the color convergence and the picture still seems to be a bit off and now the whole screen seems to lean down on the right side.


Is the static colour bent also? It shouldn't be.
It takes hours some times top set these things up.
Cover one colour up with a piece of card whilst setting another to the donor colour. Usually Green stays static for this purpose.
Hope that helps.

Dec 24, 2010 | Mitsubishi WS-65807 65" Rear Projection...

1 Answer

The screen turns green in places and wont come back to the right colour


the screen composed of three color if one of them defective its color the whole screen.. or maybe partially open or shorted parts inside.

Jun 19, 2010 | Goodmans GTVL19W17HDF 19 in. LCD TV

2 Answers

Colour convergence on a projection TV


hello it sound like convergance chips may be the problem

shaun

May 11, 2009 | Philips 43P8341 43" Rear Projection...

1 Answer

When i turn my goodmans plasma tv in and switch it on i just get a faint blank screen and the red power light dosen't come on can you help me with this please thankyou


Hi this is abhishek and welcome to fixya,
it is the problem of colour wheel see whether any burnt resistors it may be also a cause if its not its definitely colour wheel problem..better to change it or fix it

thank u..........

May 03, 2009 | Goodmans GTVL32W27HDF 32 in. LCD TV

2 Answers

Colour problem


6b5ee7e.png You may have a convergence problem. Here are some of the most common symptoms.

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.


You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick email and they will put one together for you. Their kits includes photo instruction guides, original Sanyo STK chips, convergence resistors, pico fuses, etc.

Dec 31, 2008 | Toshiba 42H81 42" Rear Projection...

1 Answer

Hitachi 43FDX01B (convergence) problem


hi i have same prob iv bin told its a convergence chip an thay r £150 ! thay go bout evry 6 years an its comon .. any way there coming 2 fix mine 2day so ill let u know if it sorts it out my mail is mjoutlaw@hotmail.co.uk thanx

Jan 30, 2008 | Hitachi 51F500 51" Rear Projection...

1 Answer

Ps2 to goodmans tv


Which version of the PS2 do you have (NTSC or PAL)?
And same question about the TV?

Dec 30, 2007 | Sony PlayStation 2 Slimline Console

3 Answers

Colour problem on rear projection tv


This might be something really simple... In a large number of DPTV310 chassis, of which this TV is, the yoke connections where put in place with black electrical tape just below the retaining rings. Job is to loosen the rings, remove the tape and push the yoke back in place and tighten down retainer.. Be careful not to throw off the tilt of the yoke. The adhesive on the tape, over time, gets hot so many time it becomes slippery and allows the yoke to fall away from it's position dulling the look of the image (or focal length) causing the problem you're describing here... It also throws off the convergence - so in attempting to converge it just looks worse. Good Luck Bill

Jun 10, 2007 | Philips 60PP9352 60" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75990 Answers

Cindy Wells

Level 3 Expert

5676 Answers

Marvin
Marvin

Level 3 Expert

83772 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...