Question about RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Nail comes out another hole

When I fire my paslode trim gun, the nail comes one inch through a hole in nail sleeve

Posted by on

  • David Ford
    David Ford May 11, 2010

    are the nails installed properly? if not that can happen

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,176 Answers

Are you using the right nails and are they inserted properly if this is an angle gun? Also look for a jammed nail that might be causing this. look at the magazine bolts to make sure they are tight. You can go to Paslode.com for the owners manual and troubleshooting guide.

Posted on Sep 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My paslode impulse 1m50f18 fires normally but no nail apears with paslode nails?


not sure what you mean" no nail appears with paslode nails" if it fires make sure the nails are correct for your gun

Sep 08, 2015 | Air Tools & Compressors

1 Answer

Looking for the nearest repair shop for paslode nail gun in Northren Va


Have all the nails been cleared out of the tool where they were jammed? If not take the fuel cell out of the tool, and remove the battery before working on it. If still persists come back to this website for further help.

Sep 19, 2014 | Omega Paslode 901000 Impulse Cordless...

1 Answer

Paslode 900600 Trim nailer not sinking nails


The firing pin can be completed or part of it crooked worn and can have a little burr on its way and stuck in the cylinder somewhere o-rings worn and hardened, have a tilting piston on the firing pin somewhere in the cilinder

Jul 27, 2017 | Air Tools & Compressors

1 Answer

My paslode f 16 nail gun wont fire nails,new gas. it actually fires but nails wo nt eject.


i found this happening to me and i oiled (light oil like 3 in 1) the driver (hammer) in the tip. that way it could retract and drive the next brad.

Jul 30, 2010 | RTO Paslode 902000 IM250 Ii Cordless 16...

1 Answer

Paslode nail guns won't shoot


piston is probably jammed

This happens sometimes try holding it up against a board with the trigger depressed and then inset the battery.

The goal is to try to force the firing sequence to get the piston back to the right position with corded units this is simply done by attaching the air hose with the trigger pulled this causes air to rush into the gun chamber pushing the piston back and firing a nail out.

The cause of this is a misfire or jammed nail that stopped the piston in the wrong location so air will not build in the chamber correctly.

Hope that helps

Feb 18, 2010 | RTO Paslode 902000 IM250 Ii Cordless 16...

1 Answer

Were can i buy a instruction manual for a paslode


go to Paslode.com and you can download the manual for free. Let me know if you have any problems

Dec 11, 2009 | RTO Paslode 902000 IM250 Ii Cordless 16...

1 Answer

I have a paslode nail framer 900600. the problem i have is the same after 3 exchanges. The gun will stop firing. i have oiled it, replaced gas,etc. the hammer simply will not come down to force the nail...


It may be as simple as making sure the spark plug lead is in the spark unit all the way.( Black box in the handle). Good Luck!! If you get stuck call Adelaide Nail Gun Repairs. They may be able to help you over the phone.

Oct 11, 2009 | RTO Paslode 902000 IM250 Ii Cordless 16...

2 Answers

Paslode air framer not sinking some nails


Your air pressure is dropping everytime you fire. It sound like your compressor is not cutting back in untill it to low. Not giving your tool enough continuess pressure. Your compressor cut in pressure should be around 90-100psi no less. and your max. pressure no more then 120psi. (Make sure your regulator is set at 110psi)
good luck...!

Aug 11, 2009 | RTO Paslode #650027 2500CT Placement Nail

1 Answer

Firing pin not retracting far enough to allow nails forward


Yes,this is a common "mis fire" by Pasilode. I own the 16p Framer and the Angle nailer and I never get it from the Framer but I do get it seldom from Trim Gun,nothing you can do ,its just a misfire.

Please rate jj505

Mar 20, 2009 | RTO Paslode 902000 IM250 Ii Cordless 16...

Not finding what you are looking for?
RTO PasLode 900420 Impulse Framing Nailer  Logo

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top RTO Air Tools & Compressors Experts

yoopertech

Level 2 Expert

131 Answers

John Trevino

Level 3 Expert

1383 Answers

Brad Brown

Level 3 Expert

15691 Answers

Are you a RTO Air Tool and Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...