Question about Wmh Tool Group 10" 1 - 1/2 Hp Workshop Table Saw

1 Answer

Plug the saw in switch it on and won't run - Wmh Tool Group 10" 1 - 1/2 Hp Workshop Table Saw

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Many models have a 'breaker' on them somewhere if the motor overheats, pulls too much current, etc. You may need to crawl under your saw, depending on the model, and reset it (typically a red button to press in). Otherwise, make sure the receptacle you have plugged it into is not tripped by plugging something into it that you know works.

Posted on Sep 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dewalt Model D304-04 reciprocating saw wont run. I plug it in, pull the trigger and it wont start. What am I doing wrong or what could the cause be?


Hi Fred:
Hmmmmm.
- Confirm there is power in the plug.
- use continuity meter to check that there is a complete circuit through the saw.
- broken connection in plug?
- broken wire between plug and switch?
- switch not functioning?
- switch set between forward and reverse?
- Speed control potentiometer contacts dirty?
- Bad brushes?

Aug 25, 2015 | Dewalt Saws

1 Answer

My ryobi BTS10 won't start.


The Ryobi does have an overload protector (PN 452110003) inside the switch box. It should be resettable from a small hole to the right of the switch on the front of the cabinet. If not, you may have to go into the switch box to check it out/reset it. If the overload protector is OK, I'd check the condition of brushes and brush springs next.

Jan 21, 2013 | Saws

1 Answer

Won't start; plug looks good and has spark and it's getting fuel


Did you use the right fuel mix.? Does it still have good compression.? Have the piston rings been damaged.?
Check ignition switch.

Dec 20, 2012 | Husqvarna Chain Saw Models 371, 372xp

1 Answer

Won't run


These tools are well known for overheating and failure (breaking off) one of the prongs that the battery connects to. This is part of the switch so it would need a new switch if this is the case.

Aug 13, 2012 | Dewalt 10.0 AMP Reciprocating Saw

1 Answer

Problem with m y dewalt 704 mitre saw type 1, at first the trigger stuck, and now the saw won't run at all, any help would be appreciated.


you need to change switch,when trigger stuck,2 contact on switch weld ,after no contact at all because of wear

Jun 04, 2012 | Dewalt Tools & Hardware - Others

1 Answer

Husqvarna 372xp won't start... Mysterious


I recently bought a brand new 372XP and spent the first day trying to start it as per the instruction manual with no success, never even fired once. Removed the plug to find plenty of fuel and that the plug has a good spark. Left it until the next day mainly to allow my arm to recover (& scour the internet for clues). I found a forum that said not to use the decompressor and sure enough without the use of the decompressor button it fired first go with the choke on then I reset the choke & it ran properly on the second pull. The decompressor button can be reset with fine nosed pliers or removal of the top cover by undoing three screws. Good luck it's a great saw once you know how to start it.

Apr 01, 2012 | Husqvarna Chain Saw Models 371, 372xp

1 Answer

I have a husqvarna 450 that won't stay running and has oil coming out the excaust


It sounds well flooded, remove the spark plug, with the kill switch to off, crank the engine five or six times to evacuate any excess fuel in the cylinder, leave the machine for an hour or so, re fit the plug and attempt starting with no choke.

May 30, 2011 | Husqvarna 450 e-series 18" Chain Saw

1 Answer

Saw runs continuously


The on off switch has a contact that has probably fused together from making and breaking causing an arc. You may try giving it a good 'wrap' with the back of a screw driver to free it, or replace the switch.

Jul 15, 2009 | Hitachi C10FCE2 10" Compound Miter Saw

1 Answer

Delta Table Saw stopped running


I have a table saw that the cord from the motor plugs into the the back of the on/off switch. I yours is configured like that, unplug the motor cord from the back of the switch and plug it in to the wall and see if the motor will run. If so replace the switch.

Jun 21, 2009 | Delta 10"Hybrid Tablesaw with 30"Unifence

Not finding what you are looking for?
Wmh Tool Group 10" 1 - 1/2 Hp Workshop Table Saw Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Wmh Tool Group Saws Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Tom Chichester

Level 3 Expert

36353 Answers

ray gallant

Level 3 Expert

46271 Answers

Are you a Wmh Tool Group Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...