Question about Timex 1440 Nylon watch

1 Answer

Mid size sportsman, time set problem

Mid size sportsman, watch is locked up. can not set time. did get to set alarm for T1. main screen has small M in left corner then a number, the word date and a sec.? counter
time is shown below, not correct, and pressing st/stop does not do anything but show the date, also not correct.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: mid size sportsman, time set problem

your 3 button watch is set by the atomic clock at 1:am daily,to do it manually press lap/reset it can take up to 2 minutes to flash set at that point clickmode and begin,any questions

Posted on Jan 06, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My alarm wont go off

mcdevito75 here, Press MODE for each function till you reach Alarm, set time for alarm then put alarm on, if you have t1 and t2 times you"ll have to do this twice.

Oct 26, 2010 | Watches

1 Answer

I have an aquatech watch and don't know how to set it.

Thank you for contactng FixYa.
Setting the Time and Date
  • To set the time and date on your Aquatech watch, begin by pressing the "Mode" button three times to access the time setting screen. Use the "Lap/Reset" button to set the hour on your watch. Use the "Start/Stop" button to advance the numbers to reach the correct hour. When you've set the hour, use the "Lap/Reset" button to set the minutes, using the "Start/Stop" button to advance to the correct minute. Repeat the procedure to set the seconds, month, date and day of the week on your Aquatech watch.
  • Setting an Alarm
  • To set an alarm on your Aquatech watch, begin by pressing the "Mode" button two times to access the alarm setting screen. Use the "Lap/Reset" button to set the hours place, using the "Start/Stop" button to reach the correct hour. Repeat the same procedure to set the minutes for your alarm. When you have finished setting the alarm, activate it by simultaneously holding the "Lap/Reset" and "Start/Stop" buttons until the alarm icon appears. When the alarm sounds, silence it by pressing the "Lap/Reset" button.
  • Deactivating the Hourly Chime
  • Many Aquatech watch models feature an automatic hourly chime. This can be inappropriate and inconvenient in many situations. To deactivate the hourly chime on an Aquatech watch, simply press and hold the "Lap/Reset" and "Mode" buttons simultaneously. After you have correctly deactivated the hourly chime, the hourly chime indicator icon will disappear from the watch's main screen.

  • Best regards. Jewel

    Sep 18, 2010 | Watches

    1 Answer

    Mid Size Sports 1440 Black Nylon Strap Watch: hi i forgot how to set the time on my timex 1440 s...


    You can easily change the time of your Timex watch by following the steps below.

    1. With the time and date showing, press the top left button.

    2. Press the right top button (this sets seconds).

    3. Press the bottom left button. This flashes the hour; press the top right button until you have the correct hour (there is no symbol for am, pm will show if pm).

    4. Press the bottom left button, minutes flash. Press the top right button until correct minutes.

    5. Press the bottom left button, month flashes. Press the top right button until correct.

    6. Press bottom left button, date flashes. Press the top right button until correct.

    7. Press bottom left button, day flashes. Press right top button until correct.

    8. Press bottom left button, time format flashes (can be set to 24 hour clock). If correct, you're done. Press top left button if you're done (can be pressed at any step if you're finished).

    To turn off the chime and alarm: Press bottom left until in the alarm screen. Then press the top right button repeatedly until the CHIME or CH symbol is gone and/or ALARM or ALM to disappear, then press the bottom left button to go back to main time.

    Hope it helps.

    Thank you for using FixYa.

    May 18, 2010 | Timex 1440 Nylon watch

    2 Answers

    How to set alarm on easy set alarm

    You can get instructions from the Timex web site "".

    At the
    bottom of the screen click on "manuals/downloads", then on "product
    manual download"

    Enter your watch type in the search box and click on "search"

    Feb 08, 2010 | Timex Expedition 84601 Wristwatch

    4 Answers

    How to set alarm on seiko chronograph sports 100

    pull the crown out to the first click press the reset chronograph button until the hands on the small alarm dial start to move.set the alarm time press the crown back!

    Jan 15, 2010 | Watches

    2 Answers

    I have a seiko chonograph couturo alarm. 100m

    Many of the Seiko Chronographs have the same setting options (mine is the lightweight "Titanium Sports").

    First off, the alarm dial must show the same time as the actual main dial. If not you must adjust this first.

    Pull the knob at number 4 position on the watch face out, until you feel two distinct notches/clicks (around 0.5mm travel) and the alarm will make a shrill buzzing for about 1 second.

    Now turn the #4 knob to move the small alarm dial at the #6, to be the same as the actual time displayed on the main face, and press the #4 knob fully back in. This sets the alarm and the main time to the same You do not need to do this again, unless you adjust for daylight saving times during summer/winter.

    Now you can set the alarm chime point.

    Pull the #4 knob out again, but just one click. You should hear one ping from the alarm. Now press the button at #8 position. It will move the small alarm hands by 1 minute intervals, and if you keep it held in, the dial spins around quickly. This allows you to adjust the time the alarm will chime.

    When you've got the alarm time and it's chime point set, leave the #4 knob at one click out.

    If you wish to switch the alarm off simply press the #4 knob back in, and the alarm dial will spin around to the same time as the main dial.To re-enable the alarm pull the #4 out one click again. It's quite simple once you get the hang of it.

    Jan 01, 2010 | Seiko Coutura Chronograph Watch

    1 Answer

    Diesel DZ7069 watch - how do I set the correct date/time?

    ok ,here it is .
    Instructions To Set The Time On The Diesel DZ7071 Watch

    Ok the first and most important thing to know about this watch is that it has an unusual timezone function (unusual to me at least). This allows the watch to display two different times. Time 1 (or T1) is the primary time (the time of the place where you spend most of your time!). The time can only be adjusted whilst the watch is in the T1 mode (T1 should be displayed in the bottom left corner of the screen). Holding down the top right button for one or two seconds will temporarily replace the current T1 time with the T2 time. Holding down this same button for several seconds will toggle the current time mode to T2 and the watch will continue to function in the second time zone until you toggle it back to T1.

    The second most important thing to know is that you can only set the time whilst in the T1 mode. When in T1 mode hold down the top left button until the watch enters the settings menu (it should say "Light" at the top of the screen) now use the bottom left button to toggle through the settings menu until you get to the time settings. I think this part of the process if sufficiently straight forward so I'm not going to go into more details here, all I'll add is that once you have the watch set to the desired time mode 12h/24h time and date you just need to press the top left button to save the settings and return to the main time screen.

    To set a secondary timezone time you have to first toggle the watch to the secondary time zone mode (hold the top right button for several seconds and the T1 indicator should change to T2 (and the watch will now be displaying the time that is currently set for the secondary timezone). This time is based on the primary time by simply telling the watch a number of whole hours ahead or behind the primary time. To adjust this hold down the top left button for several seconds, the watch will then say "offset" now use the buttons on the right to add or subtract hours from the primary time. Once set press the top left button again to return to the main time screen. Finally hold down the top right button for several seconds once more to return the watch to the T1 mode.

    May 14, 2009 | Diesel Digital Dz7069 watch

    1 Answer

    How can i set digital time and alarm in the Timex wrist watch model is- MF13-Y-S7

    Try this ,it may work for you as i m having mf13-t1

    Press MODE then then SET
    Press ALARM to increase the count and to change time t1 or t2.
    Press MODE to switch the digit place
    finally press SET and then MODE

    Note: Check for bell and sound symbols,if they are not there
    Press MODE then then SET again press SET
    Press ALARM for once or twice depending on symbols.

    Mar 18, 2009 | Timex 27191 Wristwatch

    5 Answers

    Timex Mid Size Sports 1440 WR50M

    If your set up is: Top-Left=Indiglo Top-Right=St./Stop Bottom-Left=Mode Bottom-Right=Lap/Reset

    Than follow these steps:
    1. Press Lap/Reset and hold. You should see the time the alarm was set for.
    2. While holding Lap/Reset, press Mode.
    3. Let go of all buttons.
    4. There you go!

    Hope that was a help

    Mar 11, 2008 | Timex 1440 Nylon watch

    1 Answer

    Setting tha alarm

    Press MODE (lower left) button until "ALARM" appears in the display. Then press SET (lower right) button. T1 should flash to indicate you are setting an alarm for Time 1. Press MODE to cycle through the alarm settings. Press ALARM (upper right) button to advance the hours, tens and minutes to the desired time. When the far right of the display is alternately flashing "T1" and then "AL" you can change the chime and alarm tones by pressing the ALARM (upper right) button. The alarm is on if the middle symbol (lines) on the left of the display is shown. The hourly chime is on if the lower symbol (bell) on the left of the display is shown. When you are done, hit MODE (lower left) again to return to normal time display.

    Dec 21, 2007 | Timex Expedition 40141 Wristwatch

    Not finding what you are looking for?
    Timex 1440 Nylon watch Logo

    197 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Timex Watches Experts

    Ross Keen

    Level 3 Expert

    1126 Answers


    Level 2 Expert

    236 Answers

    Pieter Vleeshouwers

    Level 3 Expert

    1329 Answers

    Are you a Timex Watch Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides