Question about Maytag MAH2400A Front Load Washer

1 Answer

Maytag MAH2400A I have change caught in the pump.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,036 Answers

Disconnect and remove the machine to give access.
Drain the machine by holding the outlet hose low over a bowl.
You can probably tip the machine backwards onto 2 crates of food or similar heavy object, so it is almost laying down.
The pump should now be visible, and a pipe-wrench used to remove the pipe clamp and slide it back over the rubber pipe.
Then remove the pipe.
Have an old towel handy to mop up water.
Clean out the pump pipe and pump. Maybe even removing the pump.
Connect again - and compress the pipe clamp again before sliding it back. Make sure it looks right and water-tight before standing it upright again and replacing & re-connecting.
Connect power last.

Posted on Sep 09, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My fuel pump went out on 2003 Pontiac Grand Am so we put a new one in and now the fuel gage says it's only 3 quarter full when it's totally full

there maybe a problem caused when you replaced the pump. you may have to pull the pump out and make sure the gage float travels its full range and is not getting caught on something when you changed the pump.

Aug 10, 2014 | Cars & Trucks

1 Answer

Trying to diagnose a problem and have back panel off. Belt was off AND I think the cause is that the drum pulley and inner drum will not spin without a lot of pressure. I figure the motor (which appea

Either something is caught between inner & outer bowl or drum bearings need replacing. Also check outlet hose going to pump sometimes object caught there causing the bowl to be tight to turn.

Dec 11, 2013 | Maytag MAH2400A Compact Front Load Washer

1 Answer

Drum rotating unevenly, squeaking

If the drum moves up/down side/side without the outer drum moving, bearings gone, replace. To check for clothing, which I doubt, remove front seal outer section, look around outer part, to bottom you probably find clip, prise apart, front back, not side ways, refit sideways

Mar 16, 2013 | Maytag MAH2400A Front Load Washer

1 Answer

Suds error maytag neptune

check for water left in units tub,if so check pump inlet and outlet and drain pipe in the house for foreign objects,then if clear make sure pump drain is running if it is,but noisy it may be bad,as in the impeller on the motor shaft may be loose and the water may stall the pump

Oct 22, 2012 | Maytag MAH2400A Front Load Washer

1 Answer

Whirlpool cabrio discharge pump makes grinding noise when draining.


That noise is a indication of something caught in the pump and rubbing on the pump impeller,what would need to done is to take apart the pump and check for foreign objects being caught in it such as a coin, a key, a peice of jewelry ect ect...


Sep 17, 2011 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer


Hi, are you sure your pump is operating properly any little thing caught in the impeller will stop these pumps. You also say there water still in the tub it will definitely not spin fast with water in the tub. Remove the pump and inspect the impeller sometimes there are things caught in it and other times the vanes are broken right off.

Apr 21, 2011 | Washing Machines

1 Answer

My WM5100 BEKO is not pumping excess water out and is not completing cycles

sounds like you have something caught in the drain pump remove the panels and inspect the pump to see if you have something caught in the pump

Aug 15, 2010 | Washing Machines

1 Answer

The door on my Maytag MAH2400 will not unlock. I have tried shutting off power to no avail. There is a throw rug in the washer that looks like it is caught in the door. Is there a manual release that...

Sorry no theres not,And when you get the throw rug out do not put these in there they do a lot of damage they can clog the pump.First thing try pushing the start button agin you well have to do this several times the machine has to drain before the door opens,when it open up.put draino-max and let it stand for 1-2hrs and run machine no clothes.And no more throw rugs

Jul 04, 2010 | Maytag MAH2400A Front Load Washer

1 Answer

Repalced fuel pump on 1997 voyager and gas guage

well either the fuel sender got caught on the tank baffle or your other sender was going bad

May 05, 2010 | 1997 Plymouth Voyager

1 Answer

I am getting an OE code on the display. I changed

Make sure you check to see if anything is caught inside the drain line, or the bottom bellow (black hose that connects from the tub to the drain pump/motor.)

Mar 25, 2010 | LG WM2487H Front Load Washer

Not finding what you are looking for?
Maytag MAH2400A Front Load Washer Logo

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides