Question about Canon PIXMA MP530 All-In-One InkJet Printer

Open Question

I have the same problem, anyone found the solution?

Alarm keep blinking as well as copy button. Can do nothing and when lift up the cover, ink tray does not move to the centre.

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
michael_grey
  • 365 Answers

SOURCE: Waste ink near full Cannon Multipass MP730

Yes
The stop key is right above the start key.

Posted on Jun 23, 2009

Ad
komguy
  • 2306 Answers

SOURCE: Printer went into alarm mode and won't reset after changing Ink.

There is an error inside, could mean it just needs a good cleaning and lubrication, could be paper scraps, dirty encoder strip, worn out purge assembly, any number of things.

Posted on Aug 12, 2009

Testimonial: "Thank you. Your diagnosis is correct. My service station replaced a dirty carridge and replaced the ink tanks. for a fee of $50 for an instant repa"

  • 232 Answers

SOURCE: Alarm lights keep blinking after I changed my printer ink.

E5 means cartridges error - to fix press the "stop\reset" button for 5-7 seconds and then release it.

You can also try this:

1) With the printer power turned off but connected to a power source, while pressing the Resume/Cancel button, press and hold the Power button.
(DO NOT release the buttons. The Power LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button. (DO NOT release the Power button.)

3) While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and
Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light
alternately, Alarm in orange and Power in green, starting with Alarm LED.)

4) When the Power LED lights in green, press the Resume/Cancel button the specified number of time(s)according to the function listed in the table below. (Each time the Resume/Cancel button is pressed, the Alarm and
Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.)

4 times----Green (Power)------Waste ink counter resetting

Posted on Apr 07, 2010

SOURCE: E,3 flashing on Canon MP140

http://www.devicemanuals.com/model/Canon_PIXMA+MP150_manual.html
How to reset printer canon pixma MP150

  1. When you turn off the printer, then click STOP / RESET and the printer knopkuo POWER.
  2. Without releasing the POWER LED lights up when the power button, press 2 times STOP / RESET
  3. Release the power button, and then a second button - you hit your profile.
  4. The indicator light green. Press STOP / RESET 4 times.
  5. Turn off the printer.
http://tricks-collections.com/reset-canon-pixma-mp150-mp160-mp170-mp180-mp450-mp460-mptool-software/
http://www.klinik-printer.com/2010/02/canon-pixma-mp150-service-manual.html
Service manual above, above that a repair site, above that is a forum for help, above that is your user manual

Posted on May 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Green light flashes 7 times


LED Blinking in Orange/Green:

2 times: No paper. (ASF) [1000]; Set the paper in the ASF, and press the Resume/Cancel button.No CD-R tray. [1001]*1; Set the CD-R tray, and press the Resume/Cancel button.
No paper in the cassette. [1003]; Set the paper in the cassette, and press the Resume/Cancel button.

3 times: Paper jam. [1300]; Remove the jammed paper, and press the Resume/Cancel button.
Paper jam in the under guide. [1304]
Paper jam in the rear guide.[1303]
Front door closed. [1250]; Open the paper output tray.

4 times: No ink.[1601 / 1611 / 1612 / 1613]; Replace the empty ink tank(s), or press the Resume/Cancel button. Pressing the Resume/Cancelbutton will exit the error without ink tank replacement, however, ink may run out during printing.

5 times: The print head is not installed [1401], or it is not properly installed (EEPROM data of the print head is faulty) [1403 /1405]. Install the print head properly, and close the access cover. Or, with the print head installed, turn the printer off and on.

6 times: Inner cover open. [1841]*2; Close the inner cover, and press the Resume/Cancel button.
Inner cover open (during printing on paper). [1846]*2; Close the inner cover, and press the Resume/Cancel button.
CD-R tray guide closed (during CD-R printing).[1850 / 1855]*1; Open the CD-R tray guide, set the
CD-R tray properly, and press the Resume/Cancel button.
CD-R tray guide open (during printing to paper). [1851 /1856]*1; Close the CD-R tray guide, and press the Resume/Cancel button.

7 times:No CD-R or DVD-R. [1002] After setting a CD-R or DVD-R in the tray, set the tray in the tray guide, and press the Resume/Cancel button.

8 times: Warning: The waste ink absorber becomes almost full (approx. 95% of the maximum capacity). [1700]; Pressing the Resume/Cancel button will exit the error, and enable printing. The service call error, indicating the waste ink absorber is full, is likely to occur soon.
In repair servicing, replace the bottom case unit (QM2-1249), or the ink absorbers (QC1-4222 / 4223 / 4224 / 4263 / 4264 / 4864).

9 times: The connected digital camera or digital video camera does not support Camera Direct Printing. [2001]; After removing the cable between the camera and the printer, press the Resume/Cancel button, and
re-connect the cable.

10 times: Automatic duplex printing cannot be performed (paper size not supported). [1310]; Press the Resume/Cancel button to eject the paper being used at error occurrence. Printing will resume from on the front side of the next page.

11 times: Failed in automatic print head alignment. [2500]; Press the Resume/Cancel button, and after confirming the following, perform print head alignment again: - Set an appropriate type and size of paper (plain paper, A4 or letter). - Check that the nozzle check pattern is properly printed (all ink ejected, no faint printing). - Protect the paper output slot from exposure to excessive light.
Access cover open. [1200]; Close the access cover.



LED Blinking in Orange and Green Alternately, or Lit in Orange:

2 times: Carriage error [5100]
3 times: Paper feed error [6000]
4 times: Purge unit error [5C00]
5 times: ASF (cam) sensor error [5700]
6 times: Internal temperature error [5400]
7 times: Waste ink absorber full [5B00]
8 times: Print head temperature rise error [5200]
9 times: EEPROM error [6800]
11 times: Carriage lift mechanism error [5110]
12 times: AP position error [6A00]
13 times: Paper feed position error [6B00]
14 times: Paper feed cam sensor error [6B10]
15 times: USB Host VBUS overcurrent [9000]
16 times: Valve sensor error [6C00]
17 times: Motor driver error [6D00]
20 times: Other hardware error [6500]
Continuous alternate blinking: rom error

Aug 31, 2014 | Canon PIXMA iP2000

1 Answer

My canon pixma ip2000 lights flashing 7 times


LED Blinking in Orange:

2 times: No paper. (ASF) [1000]; Set the paper in the ASF, and press the Resume/Cancel button.No CD-R tray. [1001]*1; Set the CD-R tray, and press the Resume/Cancel button.
No paper in the cassette. [1003]; Set the paper in the cassette, and press the Resume/Cancel button.

3 times: Paper jam. [1300]; Remove the jammed paper, and press the Resume/Cancel button.
Paper jam in the under guide. [1304]
Paper jam in the rear guide.[1303]
Front door closed. [1250]; Open the paper output tray.

4 times: No ink.[1601 / 1611 / 1612 / 1613]; Replace the empty ink tank(s), or press the Resume/Cancel button. Pressing the Resume/Cancelbutton will exit the error without ink tank replacement, however, ink may run out during printing.

5 times: The print head is not installed [1401], or it is not properly installed (EEPROM data of the print head is faulty) [1403 /1405]. Install the print head properly, and close the access cover. Or, with the print head installed, turn the printer off and on.

6 times: Inner cover open. [1841]*2; Close the inner cover, and press the Resume/Cancel button.
Inner cover open (during printing on paper). [1846]*2; Close the inner cover, and press the Resume/Cancel button.
CD-R tray guide closed (during CD-R printing).[1850 / 1855]*1; Open the CD-R tray guide, set the
CD-R tray properly, and press the Resume/Cancel button.
CD-R tray guide open (during printing to paper). [1851 /1856]*1; Close the CD-R tray guide, and press the Resume/Cancel button.

7 times:No CD-R or DVD-R. [1002] After setting a CD-R or DVD-R in the tray, set the tray in the tray guide, and press the Resume/Cancel button.

8 times: Warning: The waste ink absorber becomes almost full (approx. 95% of the maximum capacity). [1700]; Pressing the Resume/Cancel button will exit the error, and enable printing. The service call error, indicating the waste ink absorber is full, is likely to occur soon.
In repair servicing, replace the bottom case unit (QM2-1249), or the ink absorbers (QC1-4222 / 4223 / 4224 / 4263 / 4264 / 4864).

9 times: The connected digital camera or digital video camera does not support Camera Direct Printing. [2001]; After removing the cable between the camera and the printer, press the Resume/Cancel button, and
re-connect the cable.

10 times: Automatic duplex printing cannot be performed (paper size not supported). [1310]; Press the Resume/Cancel button to eject the paper being used at error occurrence. Printing will resume from on the front side of the next page.

11 times: Failed in automatic print head alignment. [2500]; Press the Resume/Cancel button, and after confirming the following, perform print head alignment again: - Set an appropriate type and size of paper (plain paper, A4 or letter). - Check that the nozzle check pattern is properly printed (all ink ejected, no faint printing). - Protect the paper output slot from exposure to excessive light.
Access cover open. [1200]; Close the access cover.



LED Blinking in Orange and Green Alternately, or Lit in Orange:

2 times: Carriage error [5100]
3 times: Paper feed error [6000]
4 times: Purge unit error [5C00]
5 times: ASF (cam) sensor error [5700]
6 times: Internal temperature error [5400]
7 times: Waste ink absorber full [5B00]
8 times: Print head temperature rise error [5200]
9 times: EEPROM error [6800]
11 times: Carriage lift mechanism error [5110]
12 times: AP position error [6A00]
13 times: Paper feed position error [6B00]
14 times: Paper feed cam sensor error [6B10]
15 times: USB Host VBUS overcurrent [9000]
16 times: Valve sensor error [6C00]
17 times: Motor driver error [6D00]
20 times: Other hardware error [6500]
Continuous alternate blinking: rom error

Aug 31, 2014 | Canon PIXMA iP2000

1 Answer

How do i change the ink cartridge in my canon mp510 printer


Hi,
  1. Press the "On" button on the top panel of the printer to turn it on. Open the paper output tray at the front of the printer.
  2. Lift the entire printer cover, which should snap open. Then lift the small inner cover.
  3. Press down on the tab below each ink tank to snap out and remove the tank. Lift the print head lock lever that holds the ink tanks in place.
  4. Lift the overflow tray toward the top of the printer and slowly pull it out of the printer. Take care to avoid spilling any ink that has collected in the tray.

Good Luck!

Sep 27, 2010 | Canon PIXMA MP510 All-In-One InkJet...

2 Answers

Cant find where it gets power from - stupid to some but ???


Take a look at this:


004a708.jpg

The Power Button is indicated as "Power/Resume button"
Any problem? let me know.

Good luck.

Thanks for using FixYa.

Jul 29, 2010 | Lexmark Z600 InkJet Printer

1 Answer

Alarm lights keep blinking after I changed my printer ink.


E5 means cartridges error - to fix press the "stop\reset" button for 5-7 seconds and then release it.

You can also try this:

1) With the printer power turned off but connected to a power source, while pressing the Resume/Cancel button, press and hold the Power button.
(DO NOT release the buttons. The Power LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button. (DO NOT release the Power button.)

3) While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and
Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light
alternately, Alarm in orange and Power in green, starting with Alarm LED.)

4) When the Power LED lights in green, press the Resume/Cancel button the specified number of time(s)according to the function listed in the table below. (Each time the Resume/Cancel button is pressed, the Alarm and
Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.)

4 times----Green (Power)------Waste ink counter resetting

Apr 07, 2010 | Canon PIXMA MP240 All-In-One InkJet...

1 Answer

Alarm light on and off and so does the on/off light


it appears that the waste ink absorber of the unit is already full. youll have to consult an authorized service center to have it reset and replace the waste ink absorber.

Feb 17, 2009 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

Not working


Pull out the tray with paper.
You should find a moving plastic "tongue" near the middle of width in the area where your paper tray should go. It's a contact based flag for the device to consider how much paper is in the tray. Check if it's not broken or stuck in odd position. Move it back and forth several times, with no force, it goes very easily. When you lift the flag up, see message and blinking led stop appearing. Try to pull paper tray back in, add paper if error appears again. Enjoy!

Sep 15, 2008 | Canon imageCLASS MF5750 All-In-One Laser...

1 Answer

I have a PIXMA MX700 all in one and the factory ink tank (number 8 Magenta) that came with the printer is not recognized by the printer; causing an alarm situation that will not clear even when the tank is...


I did not have this problem until after I moved, even though I was extremely careful and moved my MX700 in its original box in my car. The problem seems to be related to the small black tray that the ink tanks sit in. The tray has all the electrical contacts on the back and if it gets loose, it may not make good contact with the ink tank carrier.

Try reseating the black tray where the ink tanks sit. After removing all ink tanks, lift up the gray lever to the left of the tanks. This releases the black tray that the tanks sit in. Remove the tray (not the whole ink carrier, just the smaller black piece inside the carrier towards the back), check to make sure the contacts on the back are clean, then reseat the tray, pressing it firmly, but not forcefully, into place. Push the gray lever back down to lock the tray in place and reinstall the ink tanks.

Nick, the Computer Guy

Jul 04, 2008 | Office Equipment & Supplies

1 Answer

Canon Multipass MP360


check out the canon website for a solution on this error.

Jun 01, 2007 | Canon MultiPASS MP360 All-In-One InkJet...

Not finding what you are looking for?
Canon PIXMA  MP530 All-In-One InkJet Printer Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1986 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...