Question about Garmin Rino 530 GPS Receiver

1 Answer

Power Switch will not turn my Rhino 530 HCx on

I can not turn my Rhino 530 HCx on unless I press the "page-enter-power" buttons all at the same time. I have read that this is a factory reset sequence, but I never have received the warning message, but the power will come back on. I have to remove the battery to turn it off.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

When I try to turn it on it comes up with the “rino” initialization screen and buzzes/vibrates at 5 second intervals. It never goes past this screen. Occasionally, for about 1 second a small white bar will appear across the bottom saying “0%. I’ve recharged the Li battery and got the same result. I’ve tried it while connected to the charger. Same result. I’ve tried using the optional 4 AA battery pack with fresh alkaline batteries. Same result. Did the factory reboot (page/enter/power buttons). Same – except instead of a buzz/vibrate I get the tone every 5 seconds. Have to remove battery to turn off.

Contacted Garmin tech support today (10/22) - hope to hear from them soon.

Posted on Oct 22, 2009

  • Hiker Bob Oct 25, 2009

    Garmin tech support suggested a hard reset and then updating the firmware. I told them the hard reset did not work and the unit still stayed at the start up screen and sounded the beep-beep tone every five seconds. The gave me an RMA to return the unit for possible hardware repair. I'll update this post when and if I get any further,

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset canon printer MP500


The reset method for Canon Pixma MP500 All-In-One Photo Printer
1. Entering into Service Mode
  1. Start with printer connected to power cord (electric source)
  2. Press and hold STOP/RESET button.
  3. Press and hold POWER button.
  4. Release STOP/RESET button without releasing power button.
  5. Click STOP/RESET two times and then release power button.
2. Reset the Canon Pixma MP500 All-In-One Photo Printer
  • After the printer entering into service mode, prepare paper on the printer paper tray
  • Press Stop/reset button for 1 times and then press power button, await till printer finished print.
  • Press Stop/reset button for 2 times and then press power button, The printer will print again. Await till printer finished print again.
  • Press Stop/reset button for 3 times then press power button to reset EEPROM.
  • Press Stop/reset button for 4 times then press power button to reset Waste Ink Counter.
  • Switch off the printer. if printer doesn't turn off, press button power until printer off

Jul 26, 2014 | Canon Pixma MP500 All-In-One InkJet...

1 Answer

My garmin rino hcx won't upload satelites


Hello,

Try performing a factory reset.
Be sure to save your favorites, routes, and waypoints before doing the reset as these will be deleted.

The factory reset is done with unit OFF.
Press and hold PAGE button and ENTER button and while holding the buttons turn ON the unit.
Reset is complete.

Dec 21, 2011 | Garmin Rino 530HCx 2.1 in. Handheld GPS...

1 Answer

My printer reset button keeps flashing. i have switched it on and off and still does not work 1p3500


Hi there

Here How to Disabling Low Ink Level Notification for Canon IP and MP, the method to reset
Ink level notification:

1. Push “resume” for 5 seconds for canon For MPXXX you must enter to service
Mode.
2. Push Power switch then remove power cord.
3. Insert plug power cord while pressing “power switch” at the same time.
4. Push Start/reset by step 2 continue Wait display shown “0′
5. Push + change display from “0′ to “1′
6. Push colour button 2 times
7. Push Power switch again, Printer will print 1 page
8. Open cover
9. Unplug power cord
10. Take out ink cartridge #40 and #41
11. Insert plug again
12. Push power switch
13. Open cover (scan cover)
14. Insert ink cartridge #40 and #41 again


Enter to service mode for canon MPXXX

With the printer powered off but connected to a power source, press the Power
Button while pressing and holding the Stop/ Reset button.
When the Power is lit, press the Stop/Reset button two times while pressing and
Holding the Power button.
When releasing the Power button and the Stop / Reset button (regardless of
Order), the printer will move into a service mode. (Waiting for menu selection)

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Feb 20, 2010 | Canon PIXMA iP3500 Printer

1 Answer

Hi, I have a Canon PIXMA iP4000 InkJet Photo Printer. Printer will not work but has orange light (by on/off button) permanently on. Will not go togreen or turn off unless I switch off at the mains. THanks


Sounds like a main board problem.

Here is a procedure for entering into the service menu.....

<Service mode operation procedures>
1) With the printer power turned off, while pressing the Resume/Cancel button, press and hold the Power button. (DO NOT release the buttons. The LED lights in
green to indicate that a function is selectable.)
2) While holding the Power button, release the Resume/Cancel button. (DO NOT release the Power button.)
3) While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons. (Each time the
Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange.)
4) When the LED lights in green, press the Resume/Cancel button the specified number of time(s) according to the function listed in the table below.

I have a PDF of the service manual available for free. GOTO www.Equipmentcity.net, and email me for a copy.

Sep 24, 2009 | Canon PIXMA iP4000 InkJet Photo Printer

1 Answer

Can i reboot my rino 530 hcx?


Yes - press the Page (lowest button on the left side), Enter (push in the center joy stick button) and Power (top) buttons at the same time. Then use the joy stick to select Yes indicating that you want to reset the unit.

Aug 04, 2009 | Garmin Rino 530 GPS Receiver

1 Answer

Etrex - can't find satellites anymore. Just stopped one day after downloading Points to my pc


Hi,

To my knowledge, a reset on a Garmin eTrex would require:
Holding down the PAGE and PAGE UP buttons while simultaneously powering the unit. The Garmin eTrex will enter the service mode/display:
- Bravo Version
- Software Version
- Time
- Internal temperature of unit
- Battery voltage
- External voltage
- Button presses
- Other tech info

You can also perform an LCD display/screen check by pressing the PAGE button 2X.

A firendly word of advice: While entering the service mode is interesting and useful, be careful which buttons you press because it is also possible to rest the unit to factory settings within this mode. Pressing "up"+"enter"+"on/off" keys in service mode will reset the eTrex to factory defaults. All presets and data will be lost.

To exit just turn it off as normal, and then turn it back on as normal. Unless you deliberately reset the GPS, nothing should have changed.

Alternately, you can try: Hold down the find, click-stick, and page buttons. Press the power button, and when the title screen appears, release the buttons. This will clear all memory (you will lose all waypoints, etc. back them up first).
Find button: bottom button on the left
Click stick: the button on the face of the unit
Page: the top button on the right
Power: the bottom button on the right

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jun 26, 2008 | Garmin eTrex GPS Receiver

1 Answer

Garmin Rino 530 stuck in DEMO MODE


Try a hard reset....with power off hold enter button and page button while turning on unit ....this should reset to factory setup, should now be able to switch out of demo mode

Jun 11, 2008 | Garmin Rino 530 GPS Receiver

2 Answers

To make un full reset


Hello Rahooty,

There is no way to set the date and time becayse the system clock in your Garmin Rhino 120 should be updating based on the information it receives from the GPS satellites. The radio should auto locate itself within about five minutes of being turned on providing it has a clear view of the sky. Once it sucessfully auto locates the radio's clock and position should reset. There does not appear to be any other reset built into the device.

Try taking the batteries out for at least 5 minutes. Then, reinstall the batteries, turn the unit on, and give the unit 5-10 minutes to auto locate. If it doesn't, you may need to contact Garmin support for additional sevice.

Best Regards,
Ken
"Go Ahead. Use Us."

Jun 05, 2008 | Garmin Rino 120 2-Way Radio

2 Answers

Garmin HCx GPS unit


The Vista HCx has an electronic compass. You don't need to be moving for it to work, but you do need to calibrate it. To calibrate the compass:
  1. Go to the Main Menu
  2. Select Setup
  3. Select Calibration
  4. You will be asked "Which Sensor Would You Like To Calibrate", select Compass
  5. You will see a page that says "To Calibrate Compass: Slowly Turn Two Full Circles In The Same Direction While Holding The Unit Level", select Enter and do this.
You need to hold the unit level for the Magnetic Compass to work correctly. The specs for a properly calibrated compass are +/- 5°

May 15, 2008 | Garmin eTrex Vista HCx Handheld GPS...

2 Answers

Garmin Rino 530 HCX Will not receive


check the volume settings for the radio



factory reset is: with unit OFF press and hold PAGE button and ENTER button while holding buttons turn ON unit reset is complete.

May 11, 2008 | Garmin Rino 530 GPS Receiver

Not finding what you are looking for?
Garmin Rino 530 GPS Receiver Logo

Related Topics:

959 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garmin GPS Experts

SHARCNET-USA
SHARCNET-USA

Level 3 Expert

2130 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

TO Lady

Level 3 Expert

638 Answers

Are you a Garmin GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...