Question about Jensen AM/FM/MP3/DVD/CD iPod-Ready Receiver w/ 7" Motorized LCD Screen Car Video Player

Open Question

16 PIN COLOR CODES FOR JENSEN VM9311TS

I NEED TO NO PLACMENT OF WIRES ON PINS

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
simplemitch
  • 752 Answers

SOURCE: Parking Brake wire on Jensen VM9311TS

It may need to see a Positive....not a ground (the brake wire rests at ground and goes positive when the pedal is pressed). but to answer your question, the brake wire for your car is Light Green and is at the brake switch above the pedal.

Posted on Sep 20, 2007

Ad
Shuttle83
  • 1139 Answers

SOURCE: Brake wire for Jensen VM9311ts

You first have to figure out which one of these wires goes to ground potential when the brake is engaged. Get a digital multimeter set it to read resistance (turn the dial to the omega symbol)and then connect one end to ground of the car try the outer ring of the 12 cigarette lighter and the other using the tip to pierce the insulation of one of the wires, then press the parking brake. The meter with the brake not pressed should have ---- when the break is pressed the meter should read 0000 or some value less then 1.000 ohm. The wire that goes to ground when the brake is pressed is the parking break wire and attach your DVD player brake wire to that. My money is on the solid green wire.

Posted on Sep 21, 2007

  • 5 Answers

SOURCE: Jensen VM9311TS DVD/CD No sound

sounds like the channels are out or the system has a malfuction on the inside i recommend you return it for a new one.

Posted on Dec 02, 2007

  • 2 Answers

SOURCE: jensen vm9311ts car tv

ground green pink wire
problem fixed

Posted on Feb 23, 2008

j_del
  • 1586 Answers

SOURCE: JENSEN VM9311TS DO I HAVE TO HOOK THE BRAKE WIRE UP AT ALL?

There isn't any code that I know of. Most DVD head units have one extra wire in their wiring harnesses, compared to a standard CD head unit. On mine, it's a peach-colored wire, and is the activation wire for the DVD feature. During the installation, the instructions call for this wire to be tapped into the emergency brake indicator light wire. The reason is this:

The e-brake indicator light is what is called a "ground complete" circuit. That means that the bulb always has power applied, but when you pull the brake, that puts a ground to the wire and completes the circuit, allowing it to illuminate. The head unit sees this ground, and activates the DVD player.

In my Jensen unit, I simply ran this wire to a ground (I used a screw near the fuse box), and I put a switch on the wire, so I could break the ground contact at will. Jensen calls for a procedure to activate DVD playback. In their instructions, they tell you to select DVD from the option menu, and when the "lawyer screen" comes up (the one warning you to park before you watch a movie), you release the e-brake for 3-5 seconds, and then reapply it. To simulate that with the switch I used, I leave the switch closed (activated), and select DVD. Then I flip the switch "off" for 3-5 seconds, and flip it back "on". This tricks the head unit into thinking I put the e-brake off for a few seconds and then put it back on, and the movie will start. Then I can drive away.

Basically, ground the wire that is used for DVD activation, and put a switch inline on it. Then you can break and reapply the ground in whatever manner is required by the manufacturer of your head unit. If there is no off/on sequence with yours, as there is with mine, simply ground the wire to a screw inside the dashboard and you're done.

Posted on Aug 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Color code radio wires for a 2013 chevy express


Audio Item Wire Color Polarity Wire Location Radio 12V red/white + radio, black 14 pin plug, pin 1 Radio Ground black/white - radio, black 14 pin plug, pin 8 Radio Ignition (low speed GMLAN) Radio Illumination yellow (dimmer) + radio, black 14 pin plug, pin 7 Left Front Speaker (+/-) dk. blue - lt. blue +,- radio, black 14 pin plug, pins 2 - 9 Right Front Speaker (+/-) orange - dk. green +,- radio, black 14 pin plug, pins 3 - 10 Left Rear Speaker (+/-) tan - white +,- radio, purple 16 pin plug, pins 5 - 13 Right Rear Speaker (+/-) tan - orange +,- radio, purple 16 pin plug, pins 6 - 14 Satellite Radio 12 Volts red/white + Digital Radio under driv dash, 16 pin plug, pin 16 Satellite Radio Ground black/white - Digital Radio under driv dash, 16 pin plug, pin 9 Satellite Radio Ignition (low speed GMLAN) Satellite Radio Antenna (coaxial cable) Satellite Audio Left (+/-) brown/white - tan/white +,- Digital Radio, 16 pin plug, pins 2 and 1 Satellite Audio Right (+/-) dk. green/white - gray +,- Digital Radio, 16 pin plug, pins 3 and 4 2016 Chevrolet Express Van Wiring

Feb 16, 2017 | Chevrolet Express Cars & Trucks

1 Answer

Going off 16 pin in back of stereo numbers in order from left to right jensen vm9311 which is 12 volt constant and acc and ground


Looks like if the harness snaps in from top...the top left would be ground... below that should be constant and right next to ground acc. FYI the harness on amazon is only $9

Sep 24, 2016 | Jensen Vm9311ts Dvd/cd In-dash Car...

1 Answer

Carburetor installtion


plugs into any timed vacuum port on the carb

Feb 25, 2014 | Cars & Trucks

1 Answer

Hi,Excuseme.I have 16 pin connecter of the JVC KD-S575. But,color of the wires does not match the position of the pin.I want to know the position of the 16 pin connecter of the JVC KD-S575 It has 2...


Car manufacturers donot keep color code. Your best bet is to order a universal adapter. JVC color code can be found in the instruction book. I will attach a picture. upload is not working. email me to jpulickal@gmail.com

Oct 02, 2013 | JVC KD-S570 CD Player

1 Answer

Starter relay placment


on the drivers side inner fender, in between your strut tower and windshild washer resovoir

Mar 19, 2013 | 1996 Volkswagen Jetta

1 Answer

Is firing order the same as cylinder number placement? If not can you please help me on this? I have a 2000 nissan quest. It is having a misfire in cylinder number 6 but where is that? I have a picture...


The diagram you have is correct. Number 6 is the cylinder to the far right and next to the radiator.
The firing order is how the plug wires are connected to the distributor cap or coil.
Keep in mind if you have a trouble code 306 it could also be caused by a faulty injector or mechanical problem.

Feb 03, 2013 | Cars & Trucks

1 Answer

How to re-wire a Compaq Presario SR2150NX Case power Switch


The plastic front of your desktop computer is the Front Panel.

The area of contact pins on the motherboard, that the wires from the Front Panel go to, is the Front Panel header.

F_PANEL_1

The Front Panel header contains connections for the Power On switch, Power On LED light, HarDDrive activity LED light, and so on.

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00864922&tmp_task=prodinfoCategory&cc=us&dlc=en&lang=en&lc=en&product=3339274

(Look at the motherboard photo. The Front Panel header is at the bottom right. Scroll down for the motherboard illustration )

There are 9 contact pins.
4 across the Top row, and 5 across the Bottom row.

The four pins across the Top row are numbered EVEN.

From the Left side going towards the Right side;
Pins 2, 4, 6, and 8. There is NO pin 10, just a blank spot.

The five pins across the Bottom row are numbered ODD.
Pins 1, 3, 5, 7, and 9.

A) Pins 2 and 4 are for the Power On switch

B) Pins 6 and 8 are for the Power On LED

(LED is dim when the computer is on? Switch the wires around )

C) Pins 1 and 3 are for the HarDDrive activity LED

(LED is dim when the harddrive is operating? Switch the wires around)

D) Pins 5 and 7 are for a Reset switch, IF a Reset switch is used.

How to know which wires are for the Power On switch, Power On LED, and HDD LED?

Follow the wires into the Front Panel. Remove the Front Panel, and follow them.
(Need guidance removing the Front Panel post in a Comment )

For additional questions please post in a Comment.

Regards,
joecoolvette

May 02, 2012 | HP Compaq Presario SR2150NX PC Desktop

1 Answer

I need a vizio vo370M schematic diagram


has anyone found a place to buy a t2d diode 94 or t2d 94 diode for a vizio vo370m power supply board, placment d106

Dec 09, 2011 | Vizio VO370M LCD TV

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

302 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jensen Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4991 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

The Knight
The Knight

Level 3 Expert

75846 Answers

Are you a Jensen Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...