Question about Canon Cameras

1 Answer

I have a Canon Power Shot. I turn it on and then

I have a Canon Power Shot. I turn it on and then it turns back off immediately. It does not say Change your battery or no picture card

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Try a different battery anyway. I had the same problem with a Kodak a couple years ago. I put in a new battery and it started working fine.

Posted on Sep 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i turn on my camera i get a e24 on the screen


In one of my canon manuals is says about E.. (see the little dots)

Camera malfunctioned. Turn off the power and turn on again, then re-shoot or play back. If the same message recurs frequentely, the camera may be damaged. Note down the error number [xx] and take the camera to a custumer support help desk. If this message happens immeadiately after you have taken a shot, the camera may not have shot the picture. Switch to play back mode and check whether the image was actually recorded.

Sorry if I can't help you more, but Canon does not give more information.

Nov 06, 2013 | Canon Powershot A1000IS Digital Camera

1 Answer

How to load film


http://www.usa.canon.com/app/pdf/compact_film/Sure_Shot_Z135_manual.pdf
The link above will take you to a .PDF that is an owners manual for the Canon Sure Shot Z135
On page 14 it lists how to load film into the camera.

1. Slide the back cover downwards
2. Insert the film
- Make sure the film is positioned above the film guide
3. Pull the film tip across until it reaches the film tip marker
- Make sure the film is flat
4. Close the back cover
5. Turn the dial to (auto)
(Turn the power on)
the camera will automatically advance the film to the first frame.
6. "1" should be displayed on the frame counter

If this show zero there has been an issue, make sure you are using the proper film for the camera

Aug 24, 2011 | Canon Sure Shot Z135 35mm Point and Shoot...

1 Answer

I keep getting "card locked!"


There are several possible causes for "memory card locked", "memory card error", or "no memory card". Troubleshooting steps for this problem are listed here.

Aug 24, 2011 | Canon PowerShot SD960 IS Digital Camera

1 Answer

After a picture is taken my canon camera power shot a520, takes quite a while to load and allow me to take another shot immediately and its very embarrassing to make ppl wait till another shot is taken.


how maney photos do you have on the memory stick you may need to free it up by downloading them to a usb stick on your computer so you can free up some memory

Dec 20, 2010 | Canon PowerShot A520 Digital Camera

1 Answer

I turn on my Canon Power shot A75. to take a


This sounds like it might be a defective CCD imager. If so, Canon should fix this for you for free, including free shipping both ways. This is regardless of your camera's warranty status. Please check this link for more info.

Applicable cameras include:
A40, A60, A70, A75, A80, A85, A95, A300, A310, S1 IS, S60, S200, S230, S330, S400, S410, S500, SD100, SD110, IXUS V2/300/400/430/500, IXY Digital 30/30a/200a/300a/D320/400/ 450/500

Oct 14, 2009 | Canon PowerShot A75 Digital Camera

1 Answer

My cannon power shot sd600 viewer doesnt turn on


Sounds like you accidentally pressed the DISP or DISPLAY button on the back of your camera. This manually turns the LCD screen on and off to save batteries. You would then use the optical viewfinder in its place. Try pressing this button one more time to see if it turns back on.

Oct 13, 2009 | Canon PowerShot SD600 Digital Camera

2 Answers

My Canon Powershot SD1000 has a fully charged battery but won't turn on at all.


Does your camera turn on when it's in playback mode? I have a similiar problem with mine. It only turns on in playback mode.

Sep 25, 2009 | Canon PowerShot SD1000 Digital Camera

1 Answer

Canon Power Shot Pro1 will not turn on


A new camera will fix problem perfectly. LOL Did you drop it? Seem like there might be a short or something similar. Had U ever play the game "Operation"? This camera need it, of cause done by the pro. LOL

Sep 09, 2006 | Canon PowerShot Pro1 Digital Camera

Not finding what you are looking for?
Cameras Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Cameras Experts

TC CAMERA REPAIR.Com...

Level 2 Expert

176 Answers

old marine
old marine

Level 3 Expert

2153 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Canon Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...