Question about Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

1 Answer

Handle relase stuck in upright position and I have the vacuum apart and I dont know what to do what am I looking for it is still stuck

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

Dirtdevil vacuums are so cheap. it's jammed. just go to a vacuum shop and get it repaired

Posted on Sep 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My vacuum is stuck in upright position


It's frustrating, but it's a common mix of vague documentation and un-obvious operation for a lot of Dyson uprights. Per the manual (
https://www.dyson.co.uk/medialibrary/Files/Dyson/Support/downloads/UK/floorcare/Manuals/dc27_uk_manual_alf_120710%20pdf.pdf ), look at page 4, you put your foot on the base of the unit and pull back with conviction on the handle. It should move. If it's feeling really iffy, make sure that the hose assembly is fully clicked into the base.

Be aware that the brush bar won't spin until the unit is reclined. This is a common feature in Dysons, since this is the position where it re-routes the suction into the handle for use of accessory heads.

Good Luck!

Jul 07, 2014 | Dyson DC27 Bagless Upright Vacuum

1 Answer

Dyson dc25 handle stuck at top of wand wont relaese


Hi there, it's Jack at Dyson.

A jammed DC25 wand may mean that the hose was twisted when the wand was last replaced on the machine. This can prevent the wand from extending or retracting fully. The video I've attached shows you the simplest way to resolve this.

If you would like any further advice from our experts, you can reach the Dyson Customer Helpline by calling 0800 298 0298 (UK), 1-866-693-9766 (US), or 1-877-397-6622 (CA).

Jan 22, 2014 | Dyson DC25 All Floors Bagless Upright...

2 Answers

Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac


On the lower right side of the body of this model is a air duct piece that can get stuck and won't allow you to use the release. Take out that piece and put it back on again to see if that will unlock it.

Nov 30, 2009 | Dyson DC07 Animal Bagless Upright Cyclonic...

1 Answer

On-off switch is stuck on


on the back of the handle down below the grip you will see 4 screws take them out.then slide the handle out towards the back.on the sides of the handle you will see small notches those are the snaps the hold it together.the handle will come apart.feel free to call me if you need help i don't charge just like to help people save money.if there is a cord cradle there you may have to take that off also,held onby 2 screws.314-628-9153

Apr 23, 2009 | Hoover U6437-900 / U6439-900 Windtunnel...

1 Answer

Formed metal wire inside handle


this bent metal wire goes right at the surface in a grove where the two pieces of the handle go together where your fingers grip it. I think it is to discharge static electricity.

Mar 27, 2009 | Oreck XL Ultra Bagged Upright Vacuum

1 Answer

Where is schematics online to replace lower hose assembly part


There is no schematic that I am aware of. I can tell you that from experience that this repair is very difficult. Basicaly the upper and lower handle unscrew along with the tank base, the hood comes off. the lower handle will split but not comes completely apart to remove the hose section. When reassembling, be sure to put the back hose gasket in the correct position. Look at it (take a picture) prior to repair first.

Feb 02, 2009 | Hoover F6212-900 / F6215-900 SteamVac...

1 Answer

The shut off switch is stuck to the on position


This sounds like you have an internal problem with the electrical switch. I would recommend you take it to a vacuum dealer who has experience with this model. This is a relatively simple reapir for a pro shop to handle.

Jan 13, 2009 | Hoover U6437-900 / U6439-900 Windtunnel...

1 Answer

Stuck in incline position


Hi.

If you look at the front left side of machine there is a removeable inspection port it will have 2 coloured buttons you press these in & pull it up to remove.
Now pull handle back as if vacuuming the floor.
Now where the inspection port was you will see that there is a square hole pull forward on the flap in front of square hole it pivots just behind the round rubber seal.
Slowly lift handle back up at the same time The part with the 2 long grooves in it must go under the flap as you lift handle.

Chris.

http://dysonmanuals.llc.nu/

Aug 11, 2008 | Dyson DC17 Animal Bagless Upright Cyclonic...

Not finding what you are looking for?
Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dirt Devil Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18392 Answers

Nick Olsen

Level 2 Expert

183 Answers

JoeVacs

Level 2 Expert

357 Answers

Are you a Dirt Devil Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...