Question about Sony BRAVIA XBR 52 in. LCD Flat-Panel HDTV

2 Answers

Program sony remote to operate dish vip722

I just bought a Sony 46Z5100 and would like to use its remote to operate my vip722 DVR. Sony requires a 5 digit code, and none of the ones in the book work. Any ideas?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

The Sony RM-YD029 Remote control will work with the Dish Network VIP722 DVR HD Satellite Receiver, but the Dish Network VIP722's Primary remote address must be set to 1.

The procedure below will allow Sony RM-YD029 remote control to operate Dish VIP722.

Using the Dish Network Remote Control -
1. Press menu 2 times to get to system info page
2. In the system info page the primary remote address is in a white box (bubble) followed by a Green TV (1)symbol that says IR and indicates you the channel your remote control one is configured. The Sony RM-YD029 will work when this primary remote address number (in the white box) is set to 1.

If the Primary Remote Address of your VIP722 Remote control 1 is not set to channel 1, here is how to change it:

1. While displaying the system info page, press and hold the SAT button on your dish network remote until all other modes are flashing, about 3 seconds.
2. then press the '1' button on the numeric pad of your dish remote
3. then press the '#' button on the numeric pad of the dish remote
4. then press the 'record' button (red dot button - stores setting)
5. At this point you should see a number 1 in front of the primary remote address on the dish system info page

Ensure you enter the corresponding IR code into your Sony remote control per the instructions in the manual or Sony's web site. My 722 works with Sony IR code - 01775.

Posted on Jan 11, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

RM-YD029 (Sony TV KDL-46Z5100's Remote) Codes:

  • Receiver (Sony STR-DH700) Code = 52172
  • DISH (VIP722 DVR) Code = 00775
  • DVD (Philips DVP5990/F7) Code = 31354

5.3 IR (DISH VIP722DVR Remote) Codes:
  • SONY KDL-46Z5100 TV = 283
  • Sony STR-DH700 Receiver = 2266

Posted on Dec 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a remote code for my dish network VIP722k DVR with my sony RMVZ320 remote


Check with DiSH for a possibly unpublished code. You may find that only the DiSH remote will work.

Jan 01, 2014 | DISH Network IR Remote Control

Tip

DISH VIP612 Amplifier Control


DISH Solo DVR VIP612 Amplifier / Receiver Control

7c06801.jpg

Would you like to program the Universal Remote that came with your Dish Solo DVR VIP 612 to control the volume of your receiver, tuner, or stereo instead of your TV's volume?

e818a57.jpg


The first step in using the Universal Remote Control that came with your Dish Solo DVR VIP 612 to control the volume level of your receiver, tuner, or stereo is to program the remote to control your audio device using the AUX mode button.

Once your remote controls your audio device in AUX mode, you probably want to continue to control the volume of your stereo even if the remote is in SAT, TV or VCR mode.

To setup your Dish Solo DVR VIP 612 Universal Remote to control the volume of your stereo regardless of which mode it is in, follow these steps:

  1. Press and hold the AUX button until all the mode buttons are lit, and then let it go.
  2. Press the POUND (#) button.
  3. Press the PLUS side of the VOLUME button.
  4. Press 0.
  5. Press the POUND (#) button. The AUX button flashes three times to tell you the programming is complete.
  6. Confirm the VOLUME buttons are operating the tuner/amplifier's volume control by pressing SAT or TV, and then adjusting the volume. Your tuner/amplifier's volume should change rather than your TV's volume.

Your Dish Solo DVR VIP 612 Universal Remote is now setup to control the volume of your stereo regardless of which mode it is in

I hope that helps.
________________________________________________________________
DISH Solo DVR VIP612 Manual Download
DISH Solo DVR VIP612 Quick Reference Download
DISH Solo DVR VIP612 Remote Code Scan
DISH Solo DVR VIP612 Program TV VCR Remote Codes
DISH Solo DVR VIP612 Program AUX (Stereo/Receiver) Remote Codes
DISH Solo DVR VIP612 Amplifier Control
DISH Solo DVR VIP612 What Is Limited Mode
DISH Solo DVR VIP612 Change Limited Mode

on Jul 05, 2010 | Televison & Video

Tip

DISH VIP612 Amplifier Control


DISH Solo DVR VIP612 Amplifier / Receiver Control

7c06801.jpg

Would you like to program the Universal Remote that came with your Dish Solo DVR VIP 612 to control the volume of your receiver, tuner, or stereo instead of your TV's volume?

e818a57.jpg


The first step in using the Universal Remote Control that came with your Dish Solo DVR VIP 612 to control the volume level of your receiver, tuner, or stereo is to program the remote to control your audio device using the AUX mode button.

Once your remote controls your audio device in AUX mode, you probably want to continue to control the volume of your stereo even if the remote is in SAT, TV or VCR mode.

To setup your Dish Solo DVR VIP 612 Universal Remote to control the volume of your stereo regardless of which mode it is in, follow these steps:

  1. Press and hold the AUX button until all the mode buttons are lit, and then let it go.
  2. Press the POUND (#) button.
  3. Press the PLUS side of the VOLUME button.
  4. Press 0.
  5. Press the POUND (#) button. The AUX button flashes three times to tell you the programming is complete.
  6. Confirm the VOLUME buttons are operating the tuner/amplifier's volume control by pressing SAT or TV, and then adjusting the volume. Your tuner/amplifier's volume should change rather than your TV's volume.

Your Dish Solo DVR VIP 612 Universal Remote is now setup to control the volume of your stereo regardless of which mode it is in

I hope that helps.
________________________________________________________________
DISH Solo DVR VIP612 Manual Download
DISH Solo DVR VIP612 Quick Reference Download
DISH Solo DVR VIP612 Remote Code Scan
DISH Solo DVR VIP612 Program TV VCR Remote Codes
DISH Solo DVR VIP612 Program AUX (Stereo/Receiver) Remote Codes
DISH Solo DVR VIP612 Amplifier Control
DISH Solo DVR VIP612 What Is Limited Mode
DISH Solo DVR VIP612 Change Limited Mode

on Jul 05, 2010 | DISH Network ViP 612

1 Answer

Sanyo TV Code for Dish remote 21.0 IR/UHF PRO only operates TV Power and Volume Functions.


Hello Witt Thomas,

I can understand the concern and wanting the remote to work the TV Menus. It is possible with our remotes, however it depends on the TV itself. I've seen instances where there are 2 TV's in one house, and 1 will do it, while the other won't.

If you have tried all of the remote codes, and none work, the only other options we have available are to try a powr scan, or teach the remote. This link http://www.mydish.com/support/teach-learning-remote-20-21 can provide the steps on how to teach that model of remote control!

Let me know if you have any other questions.

Tommy Faust
DISH Social Media Representative

Jan 16, 2013 | DISH Network ES161256 21.0 IR / UHF Pro...

1 Answer

How do i set up my wr7 remote with DIsh VIP722 DVR?


I have listed the steps below to assist with programming the remote to your TV. If you have any other questions, let me know at kimberly.escobar@dish.com.

You can lookup codes if needed here: http://www.mydish.com/support/apps/remot...

1.) Press and hold the clear TV button until all mode lights light up.
2.) Release and TV light will be blinking.
3.) Enter code and press #. The TV button should flash 3 times.
4.) Try functions (Volume, Power, etc..) and see if it is working.
5.) If no function, repeat steps 1-4 with another code.
Kimberly. Escobar
Social Media Representative
DISH L.L.C

Dec 22, 2012 | DISH Network ViP722 DTV Receiver /...

1 Answer

I have just purchased an avex universal urc-r6 remote and i cannot seem to find the way to program it for my vip 722 dvr receiver.


Hi tesmathwi572 my name is Mike Houston of DISH Network andI was going over your post and with our DISH remotes that go with the receiverwill give full functionality to change the channels as well as the DVR andaccess the Menu. Buy getting another remote from a store may not program to thereceiver to change the channels, if I can check your account information suchas account number or phone number so I can see about getting the remote thatgoes with that system. I will leave you my e-mail so you can contact medirectly. michael.houston@dishnetwork.com

Feb 23, 2011 | DISH Network ViP722 DTV Receiver /...

1 Answer

I have a DISH Network ViP722 DTV Receiver / 350-Hours Video.... Whenever I have my brightness setting below 40 on my LG TV, my Dish DVR will no longer respond to its Dish issued remote control. If I turn...


Hello! Daniel Busa with Dish Network. That would be a case of remote interference. You'll need a model 6.3 or 6.4 remote. You can set it to a uhf frequency instead of an ir that will correct the issue.

Aug 26, 2010 | DISH Network ViP722 DTV Receiver /...

1 Answer

Dish network VIP722 DVR - cant get sound to pass thru TV


HDMI is digital sound. I don't know why it's not passing through. You could run a set of audio cables to the surround sound. The not a noticable difference in my opinion.

Mar 15, 2009 | Televison & Video

2 Answers

Need Dish DVR ViP722 remote code.


If you are looking to have the Dish remote operate your TV, just do a random search for your tv. First, hold down the tv button on the dish remote until all the rest of the light up. Next press the tvpower button on the dish remote. Next, press the channel up button (this is the up arrow button) until the set turns off. When it does turn off, press the # key at the bottom right of the remote. The tv button will light and flash twice. That's it. Your done. Hope this helps.

Feb 20, 2009 | Sony BRAVIA XBR 52 in. LCD Flat-Panel HDTV

2 Answers

Remote control


this is not a great idea, youcan program your dish remote to your tv though,

Feb 19, 2008 | DISH Network DVR-625 DTV Receiver /...

Not finding what you are looking for?
Sony BRAVIA XBR 52 in. LCD Flat-Panel HDTV Logo

2,549 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

kakima

Level 3 Expert

102366 Answers

The Knight
The Knight

Level 3 Expert

74383 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...