Question about Asko W6661 Front Load Washer

1 Answer

Water outlet default

Need to find the inlet/outlet filter

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 126 Answers

Outlet filter is located behind the little square door at the bottom of the machine. The inlet filter is in the end of the inlet hose. It is also a filter in the valve on the machine.

Posted on Jan 22, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace oil; cooler on this year


  • Service and Repair
Oil Cooler Replacement

Removal Procedure

  1. Raise and support the vehicle. Refer to Vehicle Lifting.
  2. Drain the engine oil and remove the oil filter housing.
89116492

  1. Loosen the oil cooler outlet (1) and the inlet (2) lines from the engine block.
  2. Lower the vehicle.
  3. Remove the intake plenum.
  4. Remove the intake manifold.
89116493

  1. Disconnect the following electrical connectors from the water crossover:
    • The engine coolant temperature sender (2)
    • The engine coolant temperature sensor (4)
84936658

  1. Remove the water crossover bolts (1).
  2. Remove the water crossover upper and lower seals (2).
84942881

  1. Loosen the upper heat shield bolts on the left side of the exhaust manifold.
89116496

  1. Remove the oil cooler outlet line from the engine oil cooler.
  2. Remove the oil cooler inlet line from the engine oil cooler.
84942883

  1. Note the positioning of the 4 seals.
84972057

  1. Position the oil feed and return,lines out of the way and secure with mechanic wire.
  2. Remove the engine oil cooler, inlet and outlet nuts (1).
  3. Remove the engine oil cooler cover bolts (2).
84942883

  1. Remove the engine oil cooler cover.
  2. Remove the engine oil cooler.
  3. Clean all sealing surfaces.
Installation Procedure
84972056

  1. Install the engine oil cooler.
  2. Apply a 2 mm (0.08 inch) bead of RTV silicone sealant, GM P/N 12346240, in the groove around the engine oil cooler cover.
  3. Install the engine oil cooler cover.
Notice: Refer to Fastener Notice in Service Precautions.
84972057

  1. Install the engine oil cooler cover bolts (2). Tighten the engine oil cooler cover bolts to 30 Nm (22 ft. lbs.).
  2. Install the engine oil cooler inlet and outlet nuts (1). Tighten the engine oil cooler inlet and outlet nuts to 20 Nm (15 ft. lbs.).
  3. Reposition the oil feed and return lines.
84942883

  1. Install the oil cooler outlet and install the oil cooler inlet lines to the engine oil cooler. Use 4 new seals.
Tighten the oil feed and return lines to 30 Nm (22 ft. lbs.).
84936658

  1. Install the water crossover:
    • Position the crossover.
    • Install the upper and lower seals (2).
    • Install the water crossover bolts (1). Tighten
Tighten the water crossover bolts to 30 Nm (22 ft. lbs.).
  1. Connect the electrical connectors at the following locations:
    • The engine coolant temperature sensor (4)
    • The engine coolant temperature sender (2)
  1. Install the intake manifold.
  2. Install the intake plenum.
  3. Raise the vehicle.
89116492

  1. Install the oil cooler outlet (1) line to the engine block. Tighten the oil cooler outlet (1) line to 30 Nm (22 ft. lbs.).
  2. Install the oil cooler inlet (2) line to the engine block. Tighten the oil cooler inlet (2) line to 30 Nm (22 ft. lbs.).
  3. Install the oil filter housing to the engine block. Tighten the oil filter housing to 45 Nm (33 ft. lbs.).
  4. Lower the vehicle.

Dec 22, 2014 | 2001 Cadillac Catera

2 Answers

How to fix the washer "f" notification?


If doesnt drain the water first, then the pump outlet filter is blocked

Dec 02, 2014 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

How do you change a culligan water softener filter


The filter housing will have either a shut off valve before and after the housing or a valve on top of the housing that turns (Black).
Shutoffs before and after.
1. Turn both valves off
2. Push the "red button" on top of filter housing and hold to relieve the pressure off housing.
3. Unscrew housing to the left (lefty loosey, Righty tighty) You should have a housing wrench.
4. Remove filter, clean housing, lubricate the o-ring with silicone lubricant.
5. Replace filter, Screw housing back on (Hand tighten only)
6. Open inlet valve (slightly) while holding down the "red button" to relieve air in housing.
7. Open inlet and outlet valves and you are back in business.

PS if the housing is very difficult to remove.
1. Shut off inlet valve
2. Open the nearest cold water faucet and let it run until no water
3. Shut off outlet and repeat procedure as above
Good Luck, RJ
5.

Sep 29, 2011 | Culligan Sediment Water Filter

2 Answers

Water not coming into washer


water will not enter the tub. Replaced water inlet valve. Checked inlet voltage 120v. No outlet voltage at water inlet valve.

Jan 07, 2011 | Maytag Centennial 3.2 cu. ft. SuperSize...

1 Answer

I need instructions for replacing the filter on the heavy duty Sediment water filter.


Turn the water off on inlet and outlet, press and hold RED pressure relief button on top of housing.
Use filter wrench supplied and unscrew to the left. Clean housing out and replace filter. Only tighten housing by hand. It helps to press the RED relief button again after you turn the water back on to bleed off any air in filter housing before you turn the outlet back on.
RJ

Sep 24, 2010 | Culligan Sediment Water Filter Heavy Duty

1 Answer

Which tube takes water from pool to pump and which tube puts water back in on the model 633


The outlet from the skimmer goes to the pump inlet (center) the pump outlet goes to the filter inlet. The filter inlet goes to the return to the pool.

Jul 03, 2010 | Intex 2500 Gal Easy Set Swimming Pool...

2 Answers

Kenmore refrigerator: water outlet by ice outlet


HI. this will occur if the inlet valve assembly is experiencing issues, within the solenoid structure. In some cases, debris will build up, in return, not allowing the solenoid to completely close, when not in use(the solenoid can also fail as well). This will cause a slow drip, or a leaky dispenser spout.

The water inlet valve is located behind your refrigerator. Find the water supply line coming into the valve and turn it off at the source (typically under the sink). Disconnect the supply line. Remove the screws that secure the inlet valve in place.

The water inlet valve is connected by two wires. Label the wire placement on the water inlet valve before disconnecting the wires. The wires are connected to the terminals with slip on connectors

Firmly pull the connectors off of the terminals (do not pull on the wire). You may need to use a pair of needle-nose pliers to remove the connectors. Inspect the connectors and the terminals for corrosion. If the connectors are corroded they should be replaced.

Inspect the filter screen where the supply line connects. Remove any debris or deposits that may have built up using a toothbrush or warm running water. If you cannot clear the clog, it will be necessary to replace the valve (the filter is not removable on most inlet valves).


Test the water inlet valve for continuity using a multimeter. Set the multimeter to the ohms setting X100 (if available, otherwise use the nearest ohm setting). Place a probe on each terminal. The multimeter should display a reading of 200 to 500 ohms. Close inspection of the inlet valve and especially the coil may reveal the exact ohm resistance rating to test for. If the water inlet valve does not pass this test, it should be replaced.

Oct 21, 2009 | Kenmore 55612 / 55614 / 5561 / 655619 Side...

1 Answer

Drying


The E10 error code means - not filling water.
The problem could be because of clogged filters on the water inlet line or a malfunction inlet valve.
Also there is still some water inside accumulated so please do check the filter for blockages.To avoid other errors check the outlet valve and the filter as a precaution.
Good luck with the machine.Please do rate my solution.Also do post comments for further help if needed.

Apr 11, 2009 | Washing Machines

1 Answer

Inlet/Outlet light flashing


check your overflow level switch wich is located behind front kickplate on right hand side

Jul 11, 2007 | Miele 24 in. G646SC Plus Free-Standing...

Not finding what you are looking for?
Asko W6661 Front Load Washer Logo

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Oloyede Monsuru

Level 3 Expert

1417 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...