Question about Heating & Cooling

1 Answer

I work in a hotel and our lobby a/c keeps tripping off I have to continuously keep back and forth turning it on and most of the time it wont even turn on just clicks back off, or stays on for a couple of minutes and trips or not even at all not even the fan, then sometimes it will stay on for a couple of hours is this normal? My boss says thats just the way it is. But the 3 yrs i've worked here I dont remember it doing this just maybe this year.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 396 Answers

The unit is either too small to cool the area or the compressor is going out. Replace the unit, cheaper to buy a new one than to fix an old unit.

Posted on Sep 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Intermatic T104 timer wont turn pump on,despite being tripped


If override lever snaps back and forth crisp, and turns pump ON-OFF, then timer switch is good.
Try installing new trippers. The trippers wear down and start to slip over the trip lever.
If pump does not turn on-off with override, look for loose wires at breaker or pump.
http://waterheatertimer.org/How-to-troubleshoot-Intermatic-timers.html

Jun 06, 2012 | Hardware & Accessories

1 Answer

Furnace keeps tripping the breaker changed breaker and wires all good up to the furnace still keeps tripping when i try to turn power on. nothing happened to the furnace and the wires were tested up to the...


Disconnect the black power wire where it is connected to the furnace with breaker off. Put a wire nut on it and then turn the breaker on. If it continues to trip, the problem is not the furnace and you will have to trace the power wire back to the breaker box to find problem. Next, disconnect the black wire from the breaker (with breaker off) and then snap breaker on. If it trips, bad breaker. If the furnace was disconnected and breaker did not trip, you have a short either on the P C Board or the transformer.

Mar 31, 2011 | Heating & Cooling

1 Answer

I keep getting a service error B200, and the lights flash green and orange alternately. How can I fix this?


Try keeping the paper only in the bottom tray (there's a tray in the bottom) Try pulling any paper out of the top and just close that top tray. Open up the head so that u can see the ink cartridges and turn the printer on and off and maybe it will center itself again. If it's still not working (even if lights aren't red and print head wont align in the center) try manually moving the head back and forth like 18 times so you can lubricate that rail in the back that's holding it. After that, re-turn it off and on again.

Jun 07, 2010 | Canon PIXMA iP4600 Color InkJet Photo...

1 Answer

Engine service required message


If you want to reset the light/message:

Close all the doors, booth, hood etc. hatches,

1. Make sure you have Trip odometer 1 (T1) selected.
2. Turn the ignition key to 'I'-position.
3. Press the trip odometer reset - keep it down.
4. Turn the key to 'II'.
5. Wait till the service light blinks a few times or you hear a 'beep'.
6.Release the trip odometer reset.
7. Turn the key back to '0' - service light is reset.

If this doesn't work, try:
a) 2. before 3. then continue as above
b) 5. Wait until the previous mileage appears again to the trip odometer.
c) 7. before 6.

You can reset the service counter at any time. Do not forget to service your car!

Jun 06, 2010 | 2002 Volvo S60

1 Answer

6C10 - printer error?


Try keeping the paper only in the bottom tray (there's a tray in the bottom) Try pulling any paper out of the top and just close that top tray. Open up the head so that u can see the ink cartridges and turn the printer on and off and maybe it will center itself again. If it's still not working (even if lights aren't red and print head wont align in the center) try manually moving the head back and forth like 18 times so you can lubricate that rail in the back that's holding it. After that, re-turn it off and on again.

Apr 25, 2010 | Canon PIXMA MP210 Photo All-In-One Printer

2 Answers

The Insigna power light keeps turning on and off


number of issues could be the cause.

1. back light
2. inverter
3. powerboard

I cannot tell you 100 percent what it is without looking at the unit but i hope those give you a idea what it could be now I have seen where bad capacitors on the power supply board have been a issue in this model before. Please rate accordenly and leave feedback, questions Thanks

Apr 23, 2010 | Insignia LCDTV26 26 in. Television

1 Answer

Canon fax Jx300shows error B200 Pls help


Try keeping the paper only in the bottom tray (there's a tray in the bottom) Try pulling any paper out of the top and just close that top tray. Open up the head so that u can see the ink cartridges and turn the printer on and off and maybe it will center itself again. If it's still not working (even if lights aren't red and print head wont align in the center) try manually moving the head back and forth like 18 times so you can lubricate that rail in the back that's holding it. After that, re-turn it off and on again.

Jan 28, 2010 | Canon FAX-JX200

1 Answer

Error code B200


Try keeping the paper only in the bottom tray (there's a tray in the bottom) Try pulling any paper out of the top and just close that top tray. Open up the head so that u can see the ink cartridges and turn the printer on and off and maybe it will center itself again. If it's still not working (even if lights aren't red and print head wont align in the center) try manually moving the head back and forth like 18 times so you can lubricate that rail in the back that's holding it. After that, re-turn it off and on again.

Nov 30, 2009 | Canon PIXMA MP600 all-In-One InkJet...

1 Answer

I bought a new Canon PIXMA MX860. I plugged in the printer and turned it on as directed. I continue to get an error: 6C10 There is no mention of the error code 6C10 in any of the manuals or on the...


Try keeping the paper only in the bottom tray (there's a tray in the bottom) Try pulling any paper out of the top and just close that top tray. Open up the head so that u can see the ink cartridges and turn the printer on and off and maybe it will center itself again. If it's still not working (even if lights aren't red and print head wont align in the center) try manually moving the head back and forth like 18 times so you can lubricate that rail in the back that's holding it. After that, re-turn it off and on again.

Apr 08, 2009 | HP PSC1410 Printer

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

Paul Carew

Level 3 Expert

2597 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...