Question about Krups Fresh Aroma 625 Coffee Maker

1 Answer

HELP ME with this problem!!!!please

On the display panel of my machine, it says there is something

but nothing is wrong that I can tell...the machine will not come on or brew. what am i doing wrong:>>???? I have cleaned every part of it that i know about, and we havent used it but a few times.

Posted by on

  • robinbird85 Apr 18, 2009

    mine says somthings open to and there's nothing open how do i fix it



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had that happen to me. turns out the filter cover (flat plastic circle with a rectangular hole) wasn't seated correctly.

Posted on May 20, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


Unfortunately after we got our machine back together something was put back...

This advice is for the Kenmore Elite and Whirlpool Duet FRONT LOADER style washing machines. A lot of concerns have been raised about door bellows molding, mildewing, and/or ripping and needing replaced. A replacement bellow isn’t cheap (prices vary, but are around $75-80), so hopefully these helpful steps will eliminate the need to call a repair service and pay the additional labor charges. This is a repair of MODERATE difficulty. Just follow these steps:

1. Unplug the washer.
2. Remove the washer top panel by removing the three torx-type screws (or 7mm) where it attaches in the rear of the washer. The panel should slide back, and then lift off.
3. Remove the operator console by removing the dispenser and the scew(s) behind it. Take a putty knife and insert it under the console seam right above the door. If you push in slightly while pulling outwards the panel pops off. Use care not to pull or damage any of the wiring. You can leave the wires attached and simply lay the console across the top of the washer out of the way.
4. Locate the wire hoop retainer around the rubber door boot. It is located behind the rubber seam where it attaches to the door frame. Follow this hoop around to the bottom of the door opening and locate the wire tension spring. Gently pry this spring apart and pull the wire hoop from the groove. Pull the rubber boot from the frame and push it inside towards the wash tub. You will also have to remove the door boot from the fill tube on the left hand side of the door opening. There is a small wire clamp holding it in place.
5. Remove the three screws that hold the door latch assembly in place. This is on the right hand side of the door opening. You can leave the latch in place as long as you remove the screws and push it inside slightly to remove it from the front casing of the washer.
6. Remove the door by removing the screws holding the hinges in place. Use care to support the door hinges when loosening. They can bend. Set the door aside in a location where it will not get stepped on or broken.
7. Remove the lower kick panel under the door. There are 3 screws under the bottom edge holding it in place. Sometimes the panel can stick. A slight tap on either side will knock it free.
8. Remove the front washer casing by removing the four remaining screws that are holding it in place. There should be two at the top and two at the bottom. Set the front casing aside.
9. Remove the old door boot by locating the large clamp that attaches it to the wash tub. Loosen the 7mm nut and the boot will detach from the tub. Also remove the boot from the fill tube coming from the dispenser.
10. Install new door boot on the wash tub and install clamp. There should be instructions that come with the door boot with guide marks to ensure you align it correctly. Once you have the boot in place, tighten the clamp enough to where it is snug. DO NOT over-tighten or you may damage the tub and or clamp. In most cases the clamp will break.
11. Once you have the boot in place, re-install everything in the reverse order of how I explained to disassemble. Make sure you connect the door latch assembly BEFORE you re-install the outer portion of the door boot. Also, make sure you install the boot completely over the fill tube. There should be a ridge on the tube where to stop. Sometimes the tube is not inserted all way into the boot and water will leak behind it. The clamp is always difficult to get back in place. If you cannot get the clamp to go back over the tube, you can live without it. Some newer models do not have them installed. Just make sure it is a snug fit where the rubber boot fits ALL the way back to the plastic ridge on the tube.
12. When you get the point where you are ready to install the door boot back over the frame of the door opening ensure you fit it snugly all the way around the door. Beginning at the top of the door, start inserting the wire hoop back into the groove. Make sure to wire spring points towards the bottom. As you work your way around the door to the 4 and 8 o'clock positions, you will need to maintain some constant downward pressure while pulling the spring apart in order to snap it back into place. It would be advisable to use a second set of hands to hold the wire hoop in place while doing this as it has the tendency to want to come out of the groove.
13. Once the door boot is back in place, re-install the operator console and washer top.
14. At the operator console, select DRAIN SPIN, NO SPIN and press any button under OPTIONS 4 times (has to be the same button, though). This will place the washer in diagnostics mode. You should hear the door latch lock and "C00" will be displayed on the console. The washer will run through a series of tests filling the tub, tumbling, draining, and then a final spin. If you do not wish to wait for the test to complete you can press CANCEL at any time. The test checks out everything and takes about 15 minutes. Look for any leaks.

I hope you find these instructions helpful and good luck to you.

on Jan 09, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My fisher & paykel intuitive doesn't spin it drains but that's it it also was getting stuck on cycles before braking down and not spinning could it be moisture do I have to change the circuit board?

Your washer is trying to tell you something is wrong. When the cycle interrupts and the machine starts to beep, it is in "fault mode" and it is correctly trying to tell you what is wrong with it. On models that have no LCD display, (GWL10, GWL11, etc) the LED lamps that normally indicate the various stages of wash cycles become "fault code indicators". On models with a LCD display, such an IWL12 for example, the LCD display will show the fault with a description. On all Fisher Paykel washers, you will find a detailed "tech sheet" located underneath the touch module of the machine, on the left side, in a plastic bag next to the water inlet valves/mixing chamber area. This sheet contains detailed info on fault codes and diagnostics. We always ask that people first read over this sheet and become familiar with these codes and what they mean. In many instances this will get you pointed in the right direction. To gain access you must UNPLUG the washer, and remove the two phillips screws that secure the control panel frame to the washer top deck. It also helps to remove the lid for ease of removal of the control panel from the deck.(simply open the lid 3/4 of the way up and lift it right off the hinges) Be careful not to damage or tug on the wiring connector from the motor control to the touch module.
NEVER attempt to enter diagnostic mode without first re-attaching the control panel to the washer.

Apr 23, 2015 | Fisher Washing Machines

1 Answer

Can't get machine to start a cycle. When press the start/pause button, the door open light begins to flash. After a few seconds, it stops flashing and the start/pause button begins flashing. I have checked...

It is hard to tell if there is no model number. Normally, WP machine has error code appeared on the display. I guess your unit does not have display, so the combination flashing is a signal to tell you what wrong with the system. You can check the service manual normally taps inside the unit.

Oct 22, 2013 | Whirlpool Washing Machines

1 Answer

Acer p201w monitor

go to this link should help you out.... how to set display Acer p201w monitor Google Search ...There is no difference in changing the display on an Acer monitor and on a monitor from another company.
  1. Access the desktop of your computer and right click the screen. ...
  2. Click on the "Settings" tab that is on the top-right corner of the "Properties" window. ...
  3. Adjust the resolution and color to your preferences.

How Do I Change the Display on an Acer Monitor? ' It Still Works ...

Oct 24, 2017 | Computers & Internet

1 Answer

Installed new drum on my xerox xd130df. Won't print.

Could simply be out of ink ,that machine will sometimes not detect an empty toner cartridge and just sit there kind of dumb...

Mar 27, 2009 | Xerox WorkCentre XD130DF Laser Printer

1 Answer

Receiving error I fixed my own problem. I had printed out a system data sheet on my fax machine and found out that the "error" was in under sending confirn, so I went into my menu to the sending confirm section and turned it off. Then my boss tried sending the fax and it came through like nothing was ever wrong...I think the other day when my Iguana got in my office, he must have done something, as I found him perched on my fax machine....hmmmm. Thanks for the follow-up email.

Apr 09, 2008 | HP 1040 Plain Paper Inkjet Fax

1 Answer

Need help w/ethernet connection

do this go to start >> then run , type >> inetwiz << then tell it to connect using my local area network , tell it to automatically discovery of proxy , then click next, no to setup email address, "you can do later if want to" then click finish and reboot computer
then try opening internet explorer , make sure if you have a firewall "you have to allow access to internet when asked "

Let me know if that got you fixed or not

Nov 23, 2007 | Insignia D400a PC Desktop

2 Answers

Picture went off still had sound then i turned off at panel now only red timer/standy stays lit sony 61" projection

First plug in again and look at led light, the amount it blinks tells what is wrong. Then if it stays lite it tells something also. You can try Display-channel 5-volume +- Power(service mode). Then Channel 8-enter(test reset). If this doesn't work then you will have to replace somethings like F601, R607, Q601, IC601, R612, VDR601.

Oct 05, 2007 | Sony KP-61V85 61" Rear Projection...

Not finding what you are looking for?
Krups Fresh Aroma 625 Coffee Maker Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Krups Coffee Makers & Espresso Machines Experts

Billy Mac

Level 2 Expert

83 Answers


Level 3 Expert

77932 Answers

Ross Keen

Level 3 Expert

1289 Answers

Are you a Krups Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides