Question about Car Audio & Video

1 Answer

My 300 ZX has been sitting for over a year. Everything was dead until I got it fixed. Now, I cannot find the code (or disk or remote) for my Kenwood 5025 to get it playing. All it wil do when I turn it on is ask for the access code. I've taken it to Car Toys and they cannot seem find an answer for me. Thanks dorothy_stivala@yahoo.com

Posted by on

  • dorothy_stiv Sep 08, 2009

    Thanks for trying to help. Looks like the remote is the key player here so my player is just a boat anchor.



    DJS

  • dorothy_stiv Sep 08, 2009

    No. Solution did not help.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 813 Answers

Well, without the remote you won't be able to type in the code. I can provide you the unlocking procedure and the master code but still the remote is required. The procedure is:

KENWOOD SECURITY CODE CLEAR procedure

These codes are applicable for all Kenwood radios that do not have DVD or DVD screens located on unit.


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds

(so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio

stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key on the remote
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key on the remote

The security is canceled and the set enters the TUNER mode!

Posted on Sep 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does 1991 nissan 300 zx die when the motor warms up?


Is there a MIL on, what is the code if so. May very well be a coolant temp sensor or connector corroded.

Aug 09, 2014 | 1991 Nissan 300ZX

1 Answer

88 Chevy C3500 7.4L truck has been sitting for 2 years~connected and jumped battery and put gas~drove down the road fine until turned on the lights~truck acted like it wanted to turn off~boyfriend thinks...


I suspect that the battery is dead and when you turned on the lights there is insufficient current from the alternator to run everything so the ignition shut down. Have a load test done on the battery and check for bad cells as a battery sitting unused for 2 years will be sulphated up on the plates.. Fit new battery and reset the CPU with a code reader.

Nov 02, 2013 | Cars & Trucks

1 Answer

1997zx6 run good overloading flooding out gas mixing in oil kill out and want crank until sit for awhile


You definitely need to have your carburetors thoroughly cleaned out and adjusted. Sound like pilot needle's lack of sealing that causes the bowls to overflow into the cylinders.

Oct 28, 2012 | 1997 kawasaki ZX-6R Ninja

1 Answer

Just bought a 2005 ZX-10R and it came with 1 key that promptly got misplaced. Not 1990, 2005. The choices were slim so I had to pick 1990.


Yah I saw the year model selected problem myself you did the right thing call locksmiths till one says they'll come by to fix it better ask their prices first I've been told $300 but haven't had to pay it fixed many bikes for this but not your model. When you finally get the new key engrave the number somewher on the bike so you can find it again if needed. I have done this to my bike as I know that the dealer and manufacturer both don't keep the code it's yours now ones that have a new dealer lein on them the repo man may be told the number but they mostly just tow them.

Aug 16, 2009 | 1990 kawasaki ZX 10

1 Answer

Need rims for an 86 Nissan 300 ZX, just to move


Hi myrar I have 4 damn near new tires on rims that came off a 1986-87 late production 200sx...205/60-15 inch rims with trim rings and center hub caps and I have 4 locking lugs with the key for these performance tires excellent condition, i was restoring the car but had to abandon the project for a few reasons! 401 453 3045 or email me at jonyguitar@verizon.net....make me a serious offer and we will work out the details!

Jul 16, 2009 | 1986 Nissan 300ZX

2 Answers

Frozen gps magellan triton 300


The problem is being caused by a corrupt file in the internal memory. This requires a service repair to find and remove the file. Try the Jungle Ghost at jungleghost.com. They do repairs.

Jan 02, 2009 | Magellan Triton 300 Handheld GPS Receiver

1 Answer

My remote is driving me CRAZY!!!!!!!


1) Manually turn on the device to be controlled.
2) Press and hold CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button.
3) Press and quickly release the desired mode button (TV, VCR etc.) . The red indicator blinks off once.
4) Press the CHANNEL UP button repeatedly ( up to 300 times) until the device to be controlled changes channel. The red indicator blinks off with each button press. If you accidentally overshoot the code required, press the CHANNEL DOWN button to backtrack through the library until the device changes channel. Pressing CHANNEL UP changes direction forward again.
5)Press and release MUTE to install the code.

Hope it helps~

Oct 27, 2008 | Philips PM435S Remote Control

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4848 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

The Knight
The Knight

Level 3 Expert

74118 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...