Question about Mitsubishi WS-55809 55" Rear Projection Television

3 Answers

Red convergence wont move

Cant get the red convergence to move left and right

Posted by on

  • goofypam Jan 26, 2008

    red will not move left or right, only up or down and will not line up the picture is blurry as a result of this problem.

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

If the red line is blurry and you have adjusted the screen focus control and does not work then you prob have a bad red CRT or bad red CRT fluid.........

convergence STK have nothing to do with the red being blurry

Posted on Oct 23, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Bill may you help me?

I have a Mitsubishi 45" Projection TV VS-4543.
The problem I am seeing is that there is a red gosting/double image. I found out that the coil L8W01 was burnt out and the trace pad that leads to pin1 of connector VR was also burnt on the MAIN PCB board. I had replace the coil and retrace the trace pad, also I had replace a new red convergence IC STK391-020. The problem still occure. I try to adjust the color alignment and the convergence alignment using the remote controle. The red line is not thin and sharp like the blue and green line. It is blurry and wide. Also the the red wasn't able to move in to the center of the alignment pattern when trying to adjust 5 different position during the convergence adjustment. What else can cause that problem? Please Help. red convergence wont move - d57a38e.jpg


Thanks

Acqra

Posted on Jan 20, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 934 Answers

Change both STK392-570 convergence Ics (Mitsubishi Part # 267p150010) and then do a re-alignment..
Bill

Posted on Dec 09, 2007

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

SD Tech
  • 14553 Answers

SOURCE: red convergence will not move left or right on

If red will not move in some direction you have a convergence problem--most of these sets use two of the STK-392-110 convergence chips---both along with any of the protection resistors around them that are open need to be replaced and the set adjusted.

The protect resistors are usually in the 50A61 1.8 ohms and dark gray in color----You can buy a pair of the chips for less than 14 dollars plus shipping on Ebay---the resistors should all be checked--almost any electronics supplier will have those.

It depends on if you are able to do the repair yourself or have to have someone do it for you-----This set would require you getting the chassis loose and tilting if up so the bottom faces the back of the set--you will have to unplug some of the plugs to do this.

The chips are 2 1/2 inches wide and 1 1 /2 inches tall with 18 pins each---they are black in color and will have the STK-392-110 NUMBER printed on the front of them in white.

The reason they fail is because the back of each chip is metal, a white grease is applied to each when they are mounted to the two large metal heat sinks with fins to keep them cool----after several years the grease dries out and one of the chips overheats and fails.

If you think you can do this repair I can tell you what you will need and give you general instructions on how to get at the chips----

If you cannot do this repair--shop around your area as most shops charge at least 300 for this type of repair--Whoever you get to do the repair: Make sure they replace BOTH chips or you will have the same problem again in a few months.

If they say it has to go to the shop---keep looking as any good tech can do this repair in your home in about a hour---I have done hundreds of these repairs.

When you consider that the total parts cost will be under 25 dollars, if you can do this or have a friend who can do it for you---you can save the set and a lot of money.

If you get the set working---I can tell you how to get into the TECH menu to fine adjust the convergence all over the screen--in the customer menu you are usually only able to adjust in about 9 places.

IF YOU NEED HELP OR ADVICE OR INFORMATION LET ME KNOW HERE.

I am here to help people


Regards, SD TECH

Posted on Oct 28, 2009

Slinteriors
  • 8617 Answers

SOURCE: Philips 60" hdtv. Convergence problem

what is the model number of your set and I will be able to help you with your problem.

Posted on May 07, 2008

  • 8457 Answers

SOURCE: Mitsubishi WT-42413 Red Convergence will not move left right

U check all the resistors with the Ohm Meter?All the resistors u check it in tolerance?Resolders all the resistors,so it make good resistance for the ICS?U do all these steps,u still have problems,Ur ICS some how it shorted it dead,again.

Posted on Apr 02, 2010

Ecollier2012
  • 3459 Answers

SOURCE: red gun convergence problem

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projeciton sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some photos of convergence problems.

42d3683.jpg

7859b01.jpg

e87380c.jpg
Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

69189a5.pngCONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you are handy and can follow directions. You can get complete repair kits from TvRepairKits.com or click here. They have put together DIY repair kits that include the OEM parts and step by step photo instructions for each repair. If you are not handy or can't follow directions we would suggest calling a shop.

Posted on Jul 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The grid on manuel convergence is locked w/wavy lines on the red


Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projeciton sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....
  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some photos of convergence problems.

42d3683.jpg

7859b01.jpg

e87380c.jpg
Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

69189a5.pngCONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you are handy and can follow directions. You can get complete repair kits from TvRepairKits.com or click here. They have put together DIY repair kits that include the OEM parts and step by step photo instructions for each repair. If you are not handy or can't follow directions we would suggest calling a shop.

May 24, 2010 | Hitachi 51G500 51" Rear Projection...

1 Answer

Convergence 3d Image


ok.... when you go in too align the red.. you say that the red wont move.... how about the blue.. does the red move up or down left or right does the blue move up or down left or right.. this is an indication of a faulty convergence amplifier. there may be a bad connection on this generally we replace this cuircit when it happens. things that can be checked is the flat ribbion cable from the main (green) board to the convergence board. this is the one over the top of the main one that has several metal fin(HEAT SINKS) on it.

Mar 27, 2009 | GE D52GW12 52" Rear Projection HDTV-Ready...

1 Answer

51MP392H/17 Blue convergence wont move not IC chip


You could have some opened resistors low ohms that are bad go back and ck them around convergence ics.

Nov 20, 2008 | Akai PT4298HD Rear Projection Television

1 Answer

Convergence issue


try fixing the convergence 2 after your've aligned the convergence 1 - the second (accessed via the set up control) let's you adjust on 9 different axis to align the red and blue tubes to the green. you select which + sign you want to adust by pressing the corresponding number for the + ie 1 for the top left, and 9 for the lower right corner.

good luck (note - you cant change the green only the red and blue, if the whole edge is a mess try moving the image (you need to be in zoom mode, and then access the position adjustment via the pitcure set up screen.

Nov 05, 2008 | Panasonic PT-47WX49 47" Rear Projection...

1 Answer

Hitachi 43FDX01B convergence red line wont move


probably need to replace STK IC on convergence board and possibly associated low value resistor

May 09, 2008 | Hitachi 43FDX01B TV

1 Answer

Convergence problem


You need to replace both convergence ICs number STK392-110 youcan get replacements at the following link and they provide free installation instructions with pictures so you can do the job yourself . heres the link.
http://servicemanuals.vstore.ca/

May 04, 2008 | Toshiba TZ50V51 50" Rear Projection...

1 Answer

CONVERGENCE


http://www.digitalhome.ca/forum/showthread.php?t=21847

convergence ic bad

Dec 03, 2007 | RCA P46812BL 46" Rear Projection...

1 Answer

Jvc model av-56wp74


Needs convergence IC's replaced..........T.

Oct 06, 2007 | JVC AV-27850 27" TV

Not finding what you are looking for?
Mitsubishi WS-55809 55" Rear Projection Television Logo

533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1213 Answers

The Knight
The Knight

Level 3 Expert

75169 Answers

Jaime Hernandez

Level 3 Expert

2334 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...