Question about GE 32GT740 32" TV

1 Answer

Remote i need to program remote to my dish network dishpro box i dont have the manuel

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 979 Answers
Re: remote

Go online to Dish' site and click on support at appropiate screens....accordianman

Posted on Feb 19, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Need to program bell dish remote to sanyo ds32225 tv need the code for tv

Visit this site for details. The site name is "Electro-help". Type in this name to yahoo search box. pull up older post there. You will get details you want.

Jun 08, 2012 | Sanyo Standard (CRT) Televisions

2 Answers

I have a Curtis 24 inch Full HD LCD TV 2425A never used Trying to set it up and their was no book in the box it says to run Channel Auto scan .it is hooked up to Dish satelite ant. .to run the auto...

Used the tv remote go into tv Menu goto SETUP go down Ch. enter pick CABLE and enter again.Tv now will go into auto scanning for CABLE channels.After the auto scan done for the CABLE channels are finish.After this u will able to go to channel 60 to used the dish remote.

Apr 24, 2011 | Curtis Standard (CRT) Televisions

2 Answers

What is my tv code for programming my dish network remote.


Welcome to FixYa!

You can use these codes to program the Dish remote control to your Sanyo DS32920:
542, 589, 590, 591, 592,609

You may also try Power Scan Instructions. Please follow the steps bellow.

1. While at the TV locations (TV1 or TV2 depending on which key is installed), point the remote at the TV. Press and hold the TV MODE button on the remote until all four MODE buttons at the top of the remote light up.

2. Press the RECEIVER POWER button on the remote.

3. Press the UP ARROW on the remote, about one press every two seconds. Stop as soon as the TV turns off. This process may take several minutes.
4. Press POUND (#) on the remote. The TV MODE button will flash three times.

5. Press TV POWER on the remote to turn on the TV. Press VOLUME on the remote to confirm the remote controls the TV. If this does not work, return to Step 1.

Keep me posted.


Apr 07, 2011 | Sanyo DS32920 32" TV

1 Answer

Need programming codes for Samsung txk2060 for one of 2 remotes: dish network remote or a much much older One For All remote

Here are the codes I show listed for a Samsung TV;738, 516, 590, 833, 680, 858, 897, 658, 653, 794, 500, 793 ,569, 834 ,704,506, 505, 573, 717, 654, 755, 627, 647, 652, 339, 655, 656, 730, 612, 523, 526, 566. If these dont work try the below steps:
Power Scan
1.) Hold down the clear "TV" button on the remote for four seconds, then press 500 pound ( #)
2.) Hold down the clear "TV" button on the remote for four seconds, press the big power button once.
3.) Press the channel up button once per second until the TV turns off then press pound (#).

Daniel Busa
DISH Network
Customer Service

Mar 27, 2011 | Samsung TXK2060 20" TV

1 Answer

I need to program my dishnetwork remote model 6.0 ir/uhf pro to the tv. Also, I have hooked up a gamecube system to it, but cannot get the game system to come up on the tv screen. I am hoping the remote...

We would be happy to help with those two issues. First let's address your DISH Network remote to your Emerson TV. To check that the code works try severalfunctions on the remote to make sure it's the best code to use with your TV. Rememberthat some codes may not be compatible with your equipment. If this is the case,try the other codes listed for that device until you find one that iscompatible with your equipment. Remember to put your remote back into SAT mode once you're done.

Once you have your DISH Network remote programmed to your TV getting the game system to come up on the TV should be a matter of getting your TV on the input you have it connected to. This can be done by pressing the "TV/Video" or "Input" button on the DISH remote when it is in TV mode. If you are still having trouble with getting the game system to come up on your TV, call the Emerson Customer Service Department at: 1-800-256-2487.

We hope that this information gets you up and running. Thank you for being a valued DISH Network customer!

Phillip Chang
DISH Network Customer Service Representative

Feb 21, 2011 | Emerson SpongeBob SquarePants TV

1 Answer

I just got a used Durabrand tv modelBH2404D. I have programed my dish network remote, but I don't know how to program the thetv to find my dish signal, can you help?

I hope that you have gotten this resolved, but if not, here are some simple steps to try! If you are at TV1, where the receiver box is located, the tv needs to be on channel 3 or 4. Depending on the cable that is running between the receiver and the tv, the tv may need to be on an input, such as video 1 or 2. If you are at the TV2 location, where there is no receiver, then the tv needs to be on channel 60 or 73. I hope this information helps!

Becki Barned
DISH Network Customer Service

Sep 15, 2010 | Durabrand DWT2405 24" TV

1 Answer

I bought a small sansui tv from walmart, but cannot find out the code to program my Dish network remote to work with it. My Dish book is older and only lists one code (which doesn't work)

I most certainly hope that after all this time, you were able to program your remote! But if you have any questions, haven't gotten it working, or have another tv and remote that you would like to program, I am here to help! The link below is a link to instructions for a power scan. The scan scans all of the codes on the tv until it finds the right one for the remote. It sounds tedious, but it is a quick and simple way to get that remote programmed to the tv. This scan works for every DISH remote, and you can use it on any tv, so if you have a tv in the future that you want to program with the DISH, this will help! It's a very handy thing to know!!!!

Becki Barned
DISH Network Customer Service

Apr 05, 2010 | Sansui TVM1916 19" TV

1 Answer

I need a list of codes to program a rca tv to dish network remote

you need dish network remote control manual for codes.

Oct 06, 2009 | RCA F25442 25" TV

1 Answer

Sanyo FXRG Remote

Have a dish network box. ( EDGESTAR) and my remote broke. i am trying to get the code to program the AUX button to work for the dish. on my Sanyo FXRG remote. please help me!

Apr 20, 2008 | Sanyo DS27510 27" TV

1 Answer

Av mode no remote

Just off the top of my head I think the code was 720... I havent installed DishNetwork dishes in a while though.. I will double check to get you the right code.

Mar 15, 2008 | Durabrand BH1304D 13" TV

Not finding what you are looking for?
GE 32GT740 32" TV Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Standard (CRT) Televisions Experts

matt martin
matt martin

Level 3 Expert

1187 Answers

The Knight
The Knight

Level 3 Expert

66623 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a GE Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides