Question about Poulan P3314 14" Gas Chain Saw 2.0 Cuin 33CC 2 Cycl

1 Answer

My polan 14'' woodshark will not start. i changed the spark plug and ignition modual but i dont seem to be getting any spark

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,220 Answers

Try this it is most likely shorted wiring between the ignition and start switch.
Ignition Coil Test by
You may need to use a jumper wire between the threaded part of the plug and the cooling fins. You do not have to bend up the electrode. HTH

Posted on Jan 19, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1989 thunderbird sc will not start after changing ignition modual

remove one plug and placed it next to a grounded metal surface and spin the engine over and you should see a spark

Feb 20, 2014 | 1989 Ford Thunderbird

1 Answer

Kia sephia not getting spark at coil

can we start from the beginning, what happened. are you getting power to the ignition. ? with ignition on is there power to the coil ? test these with meter...

Nov 29, 2013 | Kia Sephia Cars & Trucks

4 Answers

96 jeep cheokee problems no spark

I would make sure you have voltage to the coil. Could be a fuse or relay problem. Is the check engine light on when you turn the key on ?

Aug 16, 2012 | 1996 Jeep Grand Cherokee

1 Answer

My Poulan Woodshark 14" type 2 (-2 on serial

Fuelleaking from the cap will not stop it running, 40-1 with good quaility two stroke oil shoule be fine, if there is a good spark and fuel at the plug, you need to check that the piston has not picked up, the hottest part of the engine is the exhaust side, so remove the muffler, and take a look at the piston skirt throught the open exhaust port, any signs of scuffing and it will need to come apart to check the damage.

Oct 11, 2011 | Garden

1 Answer

Saw stoped in the middle of a cut, as if i hit the kill switch. checked all of the fuel system, fuel system ok. checked ignition, no fire at the plug, or at the plug wire. i disconnected the kill switch,...

A few checks to do first, remove the spark plug, place it on the top of the cylinder ( away from the spark plug hole ) crank the engine and check for a spark, if ok, remove the muffler and just take a look at the condition of the piston through the exhaust port, any sign of damage, or scuffing and it will need to come apart for further investigation.

Apr 07, 2011 | Poulan 14" Chainsaw

1 Answer

Car does not seem to have spark.where is ignition coil car

There's a coil pack that usually sits right on top of the engine. Follow the spark plug wires. Usually the coil pack won't fail completely you might lose 2 cylinders but not all 6. Are you getting a check engine light? It could be the cam or crankshaft sensor, they send signals to the coil pack via the power train control modual.

Nov 30, 2009 | 1996 Ford Windstar

1 Answer

Grand am has bad miss. plugs have weak spark.seems to run on 2 cylinders.dont know if related but gas gauge started to read full when problem started.acted as if it were running out of gas before but would...

You should have a good blue spark accross plug gap if not pull your coil packs apart and check for carbon tracking or corrosion in tower assembly,you could also have a fautly modual.

Sep 25, 2009 | 1994 Pontiac Grand Am

1 Answer

Top burners igniter not working

It sounds to me like the spark modual has gone bad. There is a part that is usually behind the control pad and display for the range and oven. It usually looks like a rectangular black box with wires plugged into it. Thats the spark modual. With any luck it will say spark modual on it. Buy the replacement and then plug the wires in the new one just like they were in the old one. You may want to take a photo or write down where each wire goes before you remove the old part. I would also search online for a break down diagram for your appliance so you know for sure how to get to the spark modual. It is a pretty common replacement part so it shouldnt be too expensive. Sorry I couldnt be more specific.

May 15, 2009 | Magic Chef CGS3760 Gas Kitchen Range

2 Answers

Gas cooktop problems

there is a part in the cooktop called a spark modual. it controls all the ignitors when it goes bad that what it does. replace the modual to fix the problem

Nov 25, 2007 | KitchenAid 31 in. KGCS105 Gas Cooktop

Not finding what you are looking for?
Poulan P3314 14" Gas Chain Saw 2.0 Cuin 33CC 2 Cycl Logo

440 people viewed this question

Ask a Question

Usually answered in minutes!

Top Poulan Tools & Hardware - Others Experts

Brad Brown

Level 3 Expert

16973 Answers

Bill Boyd

Level 3 Expert

49101 Answers

joseph m fucci
joseph m fucci

Level 1 Expert

43 Answers

Are you a Poulan Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides