Question about Graco Apsen 3-in-1 8740 Crib

3 Answers

Need help with crib

I have a 3 in 1 crib and My mother-in-law lost my screws to puut it together. I am trying to figure out the right size. Can you help???

Posted by on

  • zammfam Dec 13, 2007

    I have lost the instructions due to moving to convert to the last stage of the 3 in 1 conversion. Can anyone assist?

  • Anonymous Feb 20, 2008

    I lost all the parts to put the crib back together and i need new ones how do i get them

×

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 214 Answers

PLEASE READ THIS,,

About 1 Million Simplicity Cribs Recalled Due To Failures Resulting in Infant Deaths NOTE: Repair Kits that immobilize the drop-side are now available
ALSO NOTE: Consumers who have participated or have yet to respond to Simplicity’s June 2007 recall of Nursery-in-a-Box cribs are strongly urged to also participate in this recall. AND ADDITIONALLY: A subsequent recall involving Simplicity drop side cribs has been issued. WASHINGTON, D.C. - The U.S. Consumer Product Safety Commission (CPSC) is announcing today a voluntary recall with Simplicity Inc., of Reading, Pa., of about 1 million cribs. The drop-side can detach from the crib, which can create a dangerous gap and lead to the entrapment and suffocation of infants. CPSC is aware of two deaths in Simplicity manufactured cribs with older style hardware, including a 9-month-old child and a 6-month-old child, where the drop-side was installed upside down. CPSC is also aware of seven infant entrapments and 55 incidents in these cribs. CPSC is also investigating the death of a 1-year-old child in a Simplicity crib with newer style hardware, in which the drop-side was installed upside down. CPSC is warning parents and caregivers to check all Simplicity cribs to make sure the drop-side is installed right side up. The drop-side failures result from both the hardware and crib design, which allow consumers to unintentionally install the drop-side upside down. This, in turn, can weaken the hardware and cause the drop-side to detach from the crib. When the drop-side detaches, it creates a gap in which infants can become entrapped. CPSC is also aware of two incidents that occurred when the drop-side was correctly installed with older style hardware, though the upside down installation greatly increases the risk of failure. The recalled Simplicity crib models include: Aspen 3 in 1, Aspen 4 in 1, Nursery-in-a-Box, Crib N Changer Combo, Chelsea and Pooh 4 in 1. The recall also involves the following Simplicity cribs that used the Graco logo: Aspen 3 in 1, Ultra 3 in 1, Ultra 4 in1, Ultra 5 in 1, Whitney and the Trio. The recalled cribs have one of the following model numbers, which can be found on the envelope attached to the mattress support and on the label attached to the headboard: 4600, 4605, 4705, 5000, 8000, 8324, 8800, 8740, 8910, 8994, 8050, 8750, 8760, and 8996. The cribs, which were made in China, were sold in department stores, children’s stores and mass merchandisers nationwide from January 1998 through May 2007 for between $100 and $300. As an immediate precaution, consumers should check to see if the drop-side is installed right side up. To do this, check to see that the slightly rounded rail with the decorative groove is installed at the top and the plain rail is on the bottom. Next, consumers should make sure the drop-side is securely attached to the tracks in all four corners.

Your crib is listed here. The website where I found this is...

http://www.consultwebs.com/products-recall-lawyers.html

scroll down to Sept. 21, 2007.

Posted on Feb 02, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Have no screws for a graco baby crib were can l find some for it

Posted on Oct 10, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Customer service number is 800-858-8323. Hope they can help.

Good luck.

Barb

Posted on Jan 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a bridgeport crib model# 48977 / MFg no. 580255 and I lost the screws and need to know what size screws are needed to put it together


Products America offers many different sets of instructions. We may be able to assist you with the instructions and the bolts/screws. You can email us at parts@productsamerica.com or call us at 800-205-9642.

Apr 18, 2012 | Baby Gear

2 Answers

Apparently the company, RT cribs went out of business. we need the toddler rails to convert from a crib to toddler bed for our classic emma convertible crib model 88EM.


We bought the rails (in case that should happen) but it came with no directions, screws, etc. and we can't figure out how to put it together.
Have you had any luck?

Aug 07, 2011 | Toys

1 Answer

How to I take apart the drop down side of this crib. I had it installed and can't figure it out


This is tricky but I have put it together and taken it apart countless times (3 kids, 2 houses and everyone switching rooms). All of the screws keeping the crib together need to be as loose as possible without the crib coming apart. I found it easiest to have someone help so they can help hold the crib. It's important not to pull the drop side apart as it will break the plastic slides (I've done this and had to replace them). Have your helper hold one side of the drop crib right against the side piece of the crib and slide the drop side down to detach it from the side your helper isn't on. once this side is detached do the same for the opposite side. On the crib side that attaches to the drop side is a "screw" that slides down the plastic slide and a "peg" at the bottom. I always get the peg out of the track and then you can slide the screw all the way down the slide to get it out.

Jan 04, 2011 | Cara Mia Louise Crib

1 Answer

I lost the instruction Manuel and I need to convert the crib into the toddler bed


First I unbolted the four arms that hold the metal bed support up and pushed it down as flat as I could. I had to do it a couple of times and go kind of slow, to get the loose arms tucked away as best I could. They still stick up a little above the rest of the frame.

After much wrestling with the wooden front panel (gate) of the crib (the one I need to remove), here is what I did:


1. Find the wooden piece that crosses the bed just behind the gate. This is an approximately 1.5-inch by 3/4-inch piece. On ours, it's just above and in front of the drawer under the crib.
2. Find the metal screw at one end of this cross piece. You will see that it is on the outside of the bed, on the short end of the bed, in line with the cross piece.
3. Unscrew it. Note that this screw actually threads into a threaded piece inserted into the cross piece in a little hole on the back side of the cross piece, about 3/4 inch from the end. If this little silver metal piece falls out, you will need to find it and put it back in the hole with the threads facing the screw hole. The piece is the size of a pea.
4. Anyway, use an allen wrench to remove the screw, without losing that little inserted thingy.
5. I'm not saying this is textbook, but I then forced the end of the crib away from the rest of the crib while moving the gate up and down and pulling gently toward me (to pull the gate from its track). You have to move the end of the crib to create about a 1/2-inch gap before the gate will pop free.
6. The gate has two pins on each side, so when you get it freed on the site that you removed the screw on, the other side will come off without removing the second screw on that side.
7. I then got the drawer back on its tracks properly (it jumped the tracks a bit in the process), pushed everything back together the way it was, and screwed the screw back in. (if the screw wont thread, either you lost the aforementioned little silver piece, or that little silver piece is turned in the hold the wrong way)
8. With the gate removed, the crib (now toddler bed I guess) has four little tabs where the gate was once attached. Two I had to unscrew, and the other two I grabbed with a pliers and pulled out.

It wasn't elegant, but I certainly have an intact toddler bed now.

Hope helps. Good luck.

Oct 04, 2010 | Toys

1 Answer

We lost the bolts and screws to put together our jenny lind crib. what size should we buy?


call Million Dollar Baby parts at 1-323-728-9988 x120 and give them model and serial number.  If no help call us at 770-974-8895 or email us at lglbabyjunction@aol.com

Sep 01, 2009 | DaVinci Jenny Lind Crib

1 Answer

Bolts needed


either home depot, lowes , or true value hard ware

Mar 28, 2009 | Delta Luv Delta - Baby Products 5-in-1...

1 Answer

Model # 4960...help


I ended up having to take the tracks off of the crib and 'force' the slider things through. I then screwed the tracks back onto the crib. I was told that you could just leave the tracks on and the sliders would just slide right on.....that wasn't true for me. I wasted 3 hours trying their way and finally got fed up and did it my way.

Jun 26, 2008 | Delta Luv Lauren 4341

3 Answers

Jenny Lind Crib


model # 0161615 i need setup instructions

May 04, 2008 | Evenflo Jenny Lind Crib

3 Answers

Need screws to put baby bed back together (lost previous screws)


Simplicity for Children Ellis 4-in-1 Convertible Baby Crib
i lost all the screws and directions i need a new set does anyone know were i can any

Mar 24, 2008 | Evenflo Jenny Lind Crib

Not finding what you are looking for?
Baby Gear Logo

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Graco Baby Gear Experts

Joyce Nokleby

Level 2 Expert

70 Answers

Douglas Dinnebeil
Douglas Dinnebeil

Level 2 Expert

211 Answers

Dorel UK
Dorel UK

Level 3 Expert

1629 Answers

Are you a Graco Baby Gear Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...