Question about Xerox 212 Laser Printer

1 Answer

Copier is a 214 and shows U6 code

The copier was working fine, however, now it shows a U4 code and will not do anything. Your help would be greatly appreciated !

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 239 Answers

A U-6 means the memory on the main board failed.
If the machine is old, the battery on the board is old and not holding the values in the machine.
Replace the main board will correct the problem.
Since it is in the middle deep in the machine you might need to have Xerox repair it for you if they still provide service to this model.
Good luck.

Posted on Oct 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We are having xerox 1038 model usa made . we are getting the error u6 when we switch on our machine . so plz suggest us the best possible way to fix up the problem ...`````


U6-1 The main PWB failed checking the ROM.

Shut down and restart the copier. If it appears again U6-1, replace the main PWB.

U6-2 The main PWB failed checking the RAM.

Shut down and restart the copier. If it appears again U6-2, replace the main PWB.

U6-3 and U6-4 The main PWB failed to check the battery MNV (U6-3). Or the main PWB does not properly initialize the NVM (U6-4).

Follow the procedure in the development of memory to initialize the NVM, code 20-96. Shut down and restart the copier.

Jul 20, 2011 | Office Equipment & Supplies

2 Answers

Sharp Ar-5132 U6 code after moved the copier


U6 code indidcates a laser problem. It may have been shaken or bumped a little too much in the move.

Jul 28, 2009 | Sharp AR-5316 Advanced Digital Imager...

4 Answers

I have a Sharp SF-2022 copier and it flashes a U6 code abd will not work. How do I fix this?


u6 is sually something to do with the papaer tray or feed section check to make sure the tray is set properly and that you have the guide plates set correctly and that the tray is fully set

Jun 11, 2009 | Sharp AL 1631 Copier

2 Answers

I Have Xerox 5821 Star Copier and it got U6 error. Help me out


U6 code means that you have a problem with the exposure lamp or exposure lamp circuit working properly.Hold down the 0(zero) key while turning the unit on and punch in the codes 20 start 3 this will enable you to clear the code unless you have a permanent problem where a part has to be replaced

Apr 21, 2009 | Xerox 5100 Copier

2 Answers

U4 error code - Xerox 5328 copier


U4-2 Low fuser temp problem U4-3 High fuser temp problem U4-4 High fuser temp problem U4-6 High fuser temp problem

replace thermistor in fuser unit

Oct 03, 2008 | Office Equipment & Supplies

1 Answer

My machine shows a U4 code


U4 code refers to a fuser heat failure, you'll probable find the fuser roll is stone cold .Possible cause is open circuit heater or overheat thermostat popped.Either way you will need to pull out the fuser unit and check continuity of the components

May 29, 2008 | Xerox WorkCentre Pro 423 Copier

1 Answer

My xeros 214 copier has gone wrong and the no U4 is coming up, i do not have a manuel thanks terry


A U4 is a fuser overtemperature.
You can hold down the "0" while powering the machine on. That will enter the machine into diagnnostics.
Next enter code 401, and press start, See of that clears the problem.
If it does. Remove the fuser and clean the buildup off the thermistor.
If it doesnt you will most likely have to replace the fuser.

May 15, 2008 | Xerox Office Equipment & Supplies

1 Answer

Xerox Copier 214


A U4 is a fuser overtemperature.
You can hold down the "0" while powering the machine on. That will enter the machine into diagnnostics.
Next enter code 401, and press start, See of that clears the problem.
If it does. Remove the fiser and clean the buildup off the thermistor.
If it doesnt you will most likely have to replace the fuser.

Jan 29, 2008 | Xerox WorkCentre 214 Laser Printer

4 Answers

Xerox Copier Machine - Error U4


The fuser is not warming up.
On that machine under the web there is a thermal fuse on a white plastic mount, it has one screw through it.
It is most likely blown. Possibly caused by a jammed paper in the fuser.
That fusable link needs to be replaced.

Jan 02, 2008 | Panasonic DP-150A Copier

Not finding what you are looking for?
Xerox 212 Laser Printer Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Xeroxrep

Level 1 Expert

33 Answers

Philip Hughes

Level 2 Expert

72 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...