Question about Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

1 Answer

Kemore Elite Dishwasher Spews Water When Wash Cycle Begins

The machine fills just fine, but after filling and starting to wash, water spews out of the front of the machine. I know exactly where it is coming from but I cannot figure out why. We have had the machine for over 8 years and I am obsessive about how it gets loaded, so that has not changed. What could possibly change the way that the water is routed inside the machine? There are vents in the bottom of the plastic door liner, that is where the water is exiting the machine, into my wire harness and then down the face of the bottom panel.

Please Help!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

After further inspection of my dishwasher I found a bad gasket under the lower wash arm. Over the years it finally gave up and was shooting a torrent of water through the water in the bottom of the wash tub. When all that water hit the door liner it went up into the lower door vents, into to wire harness, and onto the floor.

Posted on Sep 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Machine will fill and wash , but will not fill and rinse


AS YOU SHOULD KNOW KENMORE APPLIANCES MADE BY MANY DIFFERNT COMPANIES AND WITHOUT FULL MODELL NUMBER IT IS HARD TO SAY WHAT IS PROBLEM BUT COULD BE DOOR LOCK OR MAIN CONTROLL BOARD PROBLEM

Dec 09, 2013 | Sears Kenmore Elite 3.9 cu. ft. Front-Load...

1 Answer

Water leaks (spewing) from sides of bottom of machine when it's filling up


The normal cause of leaking while it is filling is a leaking Inlet hose. Try pulling the washing machine away from the wall and watch the hoses as the machine fills. If it is leaking you can see which hose is leaking. You may either need new tighner clips or to replace the hoses depending on how bad they are leaking. Another possibility is the water pump inside the washing machine could be broken and spewing out water.

Aug 31, 2007 | Malber WD1000 Front Load Washer/Dryer

1 Answer

I have the LG wm2487h*ma front load washer.My washer is filling up with water when not in use. When I wash a load, the water does not go in the washer. Have opened the door thinking the wash cycle is done...


The problem would appear to be the water inlet solenoid valve.
The valve is not operating correctly for some reason allowing water into the machine even when switched off

Sep 02, 2017 | LG WM2487H Front Load Washer

1 Answer

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of...


Larry,
The float is generally for overflow conditions and will interrupt power to the fill valve solenoid.
If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water supply. Barring other obvious restrictions, the fill valve has filter screens on the inlet side of the fill valve, which is generally the cause of your symptoms. Be careful if you attempt to clean the screens, as the fill valves are very sensitive to debris, and can become stuck open if sediment gets past the screen. I usually replace the fill valve to avoid future problems.
Hope this helps.

Oct 30, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Stops in the middle of wash cycle


Hi!

If the cycle doesn't advance, it's probably the timer or a cold-water supply problem:
It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.
It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.
Please do rate this solution as FixYa and revert for further assistance.

Thanks
Rylee

May 29, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

As soon as you turn on power it starts to fill


It will look to the wash tank float to determine the water level and temperature. If the machine is empty, it will fill first. before letting a cycle start.

Apr 05, 2009 | Hobart LT1-1 Dishwasher

1 Answer

Basin will not fill with water during rinse cycle but will agitate and spin.


most new washers have cold water only rinse and spray rinse ck cold water coming into machine during wash if no cold comes in suspect cold side of fill vale not opening ..could be wiring issue or a bad valve

Oct 24, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

5 Answers

Kenmore Elite Calypso washer won't fill with water!


i assume that the warer is turn on at the warer valves if so then do you have voltage at the water valve if not then water pressure switch could be bad or main control board could be bad

Apr 24, 2008 | Kenmore Elite HE4 Electric Dryer

Not finding what you are looking for?
Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher Logo

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Ken Johnston
Ken Johnston

Level 1 Expert

56 Answers

Fred Sops

Level 2 Expert

272 Answers

vince

Level 3 Expert

572 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...