Question about KitchenAid Superba Architect KSCS25INSS Side by Side Refrigerator

1 Answer

Red light blinking after replacing filter

I replaced the water filter, but the red light continues to flash.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Not positvie for that model but there should be a little reset button, or try just unplugging the unit and waiting 60 secs before plugging it back in. Hope that helps

Posted on Sep 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a constantly blinking red light above the lower setting arrow...how do i resolve the problem???


1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Nov 19, 2010 | Filter Queen Defender Air Purifier

1 Answer

Blinking red light above the lowest setting on filter queen defender air purifier.


1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.

If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Sep 23, 2010 | Filter Queen Defender Air Purifier

1 Answer

How do you reset the red light on the defender when you put in a new filter? My light has never went out and I think it is supose to .


It won't go out by itself.
1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.

If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Sep 16, 2010 | Filter Queen Defender Air Purifier

1 Answer

I have a Nortitz natural gas water heater, model #N-063s-1. Acouple of days ago it stopped heating the water. what can I do myself to fix this matter. Thanks, lynnatheana@hotmail.com


There are many reasons a tankless heater will stop heating water. The first thing I would look for is a flashing red light on the burner indicator. The flash break down goes as follows

continuous blinking - typically means ignition failure or the unit is overheating; look for visible water inside the unit, have your gas pressure checked, or check the flame rod/igniter for buildup of debris

three blinks - typically indicates 16 error code; typically resolved by performing a descale

4 or 5 blinks - exotic error codes; for these you should definitely contact Noritz tech support

If there is no flashing light, first check your filter for debris. If the filter is clean, your flow sensor is probably stuck. Again I'd recommend contacting Noritz tech support to help you clean the flow sensor.

Jul 31, 2010 | Noritz 6.3 Gallon Residential Tankless...

1 Answer

"change water filter" continues to flash when dispensing water


I believe your new Jen-Air has an old model number placed above your post. If you had a newer model nuber I could see if changes were made to the solution. The ods are no changes. I it possible you may have missed removal of te flilter plug? It also is your first time and to press the 2 buttons at same time for 8 to 10 seconds may be a little confusing. I bet after this time you will have this down to an art! here is what I could find without the vorrect model number if that is what happened or not.Jenn-Air
Press and hold the light and lock buttons until the change filter light flashes.
It is very easy to reset your filter indicator light on your Maytag refrigerator. Simply press and hold the light and lock buttons, on the dispenser, for about three (3) seconds, until the change filter light blinks.
Jenn-Air Refrigerators - Press and Hold The Light and Lock Buttons until the filter light flashes (usually 5-10 seconds).

Mar 05, 2010 | Jenn-Air JCB2059G Bottom Freezer...

2 Answers

Just replaced lamp. when plugged in, power light


hello make sure the lamp is fitted securely and the lamp cover aswell

regards
shaun

Jan 16, 2010 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

TV blew out


if the lamp light is flashing u need to replace the lamp. u should have instructions on the set or in the manual

Dec 07, 2008 | Televison & Video

1 Answer

Saeco Easy


Hi,

Press the button in the upper right corner. When the light flashes, release the button.

Make sure the brewing unit, dregsbox and driptray is in position.

Try to open the steam knob and make a cup of water.

Hope this will help you.
/Mirran

Aug 07, 2008 | Saeco Easy Espresso Machine

2 Answers

No picture or sound - Power Save light blinks red 5 times - nothing on the screen


i also have the same problem with the flashing green light for a while then a different red light starts blinking on and off around 5 times....and i replaced my burnt bulb with a new one...still no picture.

Oct 24, 2007 | Sony Grand WEGA KF50WE610 50" Rear...

3 Answers

Red Light on front of Filter Queen Defender


When the red light is blinking, press and hold both up and down arrows until the red light blinks RAPIDLY, release both for a second or two, and press and hold both again until it stops blinking. It cured my problem.

Mar 06, 2007 | Filter Queen Defender Air Purifier

Not finding what you are looking for?
KitchenAid Superba Architect KSCS25INSS Side by Side Refrigerator Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4654 Answers

mike cooper

Level 3 Expert

884 Answers

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

Are you a KitchenAid Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...