Question about Dishwashers

2 Answers

Hotpoint Dishwasher 7830 Deluxe

A white surface is left on all the items after the wash cycle has finished.
Our machine is 19 years old now. However our machine matches the decor so we want to keep it.
Anything I can do to get a few more years out of my machine until we replace the whole kitchen.
Kind Regards
Paul Davidson

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,891 Answers
Re: Hotpoint Dishwasher 7830 Deluxe

The white coating left after wash/ what is call hard water filming // to clean up problem use glass majic or dishwasher majic . to keep this from happing try running the tap before starting dw. to bring the hot water to kitchen. fresh powder dergt. and no heat in dry .. you need min 120 deg to 140 is best . low water tempt is bad for best performance. mm

Posted on Dec 07, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 262 Answers
Re: Hotpoint Dishwasher 7830 Deluxe

You can change detergents i recommend eletrosol tabs they work great.Also run a mixture of vinager about 2 cups through the wash this should help
good luck

Posted on Dec 10, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Have a hotpoint dishwasher full of little black

I have a Bosch SMS 4012 works fine till cycle finished. when I turn it off it trips the power safety switch at the switch board. To prevent trips happening I have to switch off at the power point and unplug .The washer is 20 years old and the problem started around 3 months ago.Is it a major problem.

Frank. C

Feb 15, 2010 | KitchenAid Dishwashers

4 Answers

Dishes have filmy finish

hello. this will help a great deal.

First of all empty out your dishwasher, toss in two cups of plain white or cider vinegar and run it on the highest and longest cycle.

Always run the hot water in the sink first and start the dishwasher only when the water is as hot as it will get.

This wash will clean out your dishwasher thoroughly.

Then always do your dishes after you have rinsed any residue off of them before placing them in the dishwasher and I always recommend the pot scrubber cycle if you have one.

Jul 07, 2009 | Dishwashers

1 Answer

Dirty racks

What is the manufacturer and model number of the dishwasher?
Here is the process I would follow to remove the gunk.
Start a short cycle in the dishwasher, without adding detergent powder and after the (hot) water has filled the DW and the wash cycle has begun, open the DW door and add 1/4 cup of household bleach. When the water drains and begins to refill for the 2nd wash cycle, check the dishwasher to see if anything has gotten better and if not, add another 1/4 cup of bleach as soon as the hot water has refilled. Allow the DW to finish the full cycle.
Begin another short wash and as soon as the initial hot water fills and the wash cycle begins, open and add 2 cups (approximatly) of white vinegar. Allow the whole set of cycles to finish and check the insides.
If grease remains, I would use a de-greasing spray (avilable at all hardware stores and most food stores.) Spray on and use paper towels on all surfaces.
Because I do not know the make and model # for your dishwasher, I can not give you a part number for replacement racks.
Good Luck!

Apr 05, 2009 | Dishwashers

1 Answer

Water left after finishing wash

I have a Bosch Dishwasher and the E-Nr is SGS4362EU/03. The machine is approximately 4 years old, in good condition and has been working very well. Suddenly, there is water remaining after it completes a 50 degrees C wash cycle. This is also evident with the pre wash cycle and the 65 degrees wash cycle.

I have checked and cleaned the filters. I have loosened the internal pump white cover (Torx T 20 screw) and checked for any physical blockage - none. I have also checked for any drainage hose kinks - none.

I have tried a series of empty washes and the machine drains the water during the wash cycles. The dishes are also have a dull colour and show show signs of not being properly rinsed during the wash cycle.

Please assist.



Dec 27, 2008 | Bosch 24 in. SHY56A05 Stainless Steel...

4 Answers

Dishwasher leaves soap in dispenser.

Hi Dirty Dish gang.
After having 2 appliance repairmen here, I now have the latest scoop on our dishwasher problems, $200 later!
Los Angeles IS currently having hard water issues. Also, all the new cleaning gels etc. are actually a cause of our dishwasher problems.  
So, here is what we need to do:
1. Use Cascade POWDER detergent only.  Make sure is is just "plain" no "scented" or "complete"  or gel, etc. (I have tried a phosphate free powder and gel and this is a cause of our problem as well!) 2. Use Jet Dry in the dispenser (set it to a 2-3 opening) 3. Make sure water is at least 120 degrees 4. Only run dishwasher on "normal" setting.  All others just run it longer, hence causing more water stains. 5. Do not pre-wash dishes! You can knock of chunks with a "non" soapy brush, but don't rinse (the oils actually help to clean the dishes) 6.  Do not wash sponges in dishwasher.
Acid Wash: The repairman just gave my washer an Acid Wash today. It says it is an acid derived from lemon, I got mine from Carters appliance in Torrance, CA for about $19. I am to run a normal cycle with the above mentioned Cascade after this "acid cycle" is finished.
If you are still having problems:
Monthly maintenance: Glass Magic: Buy a box of Glass Magic (near the Cascade)  Use 1 Tbsb in main detergent compartment of dishwasher along with the Cascade, till washer starts working again. White Vinegar: You can run an empty dishwasher with white vinegar once a month.  Fill a bowl with 2 cups vinegar and place on bottom rack.  Then run as a normal cycle...this allows vinegar to disperse slowly.
So far it seems to be working.  Good luck.

Nov 07, 2008 | Kenmore 24 in. 16032 Built-in Dishwasher

1 Answer

Tablets not dissolving

either there is not enough water (check water valve) or the pump filters are clogged (check and clean as necessary)

Jul 06, 2008 | Maytag 24 in. MDB8600AW Jetclean II...

1 Answer

Hotpoint Dishwasher problem

are you using rinse aid? lack of this will often give a milky finish to glassware

Jun 22, 2008 | Hotpoint Dishwashers

1 Answer

Tablets not dissolving

Sounds like whatever soap you are using is just too much soap your dishwsher can handle. The soap "packs" are usulally an overload of soap for most dishwashers. Just a few teaspoons of regular name brand soap sometimes will cure lots of dishwsher ills!!!

Apr 12, 2008 | Zanussi 18 in. DA4342 Free-standing...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

479 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers


Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides