The check paper/check print cartridges keeps blinking even though *** appears fine.

its the toner light or photocondutor light?
Open door and push stop for 15/30 sec.

Incase you have used a compatible cartridge , they may not work at times . Insert the old cartridge and check , if it prints ( even though partially ) . The problem could bein the cartrige or the fitting of the same .

The HP Customer Care site says that if th check paper and check print cartridge lights are blinking, it is most likely that the carriage assembly, which holds the ink cartridges has stalled against the left side of the printer.

HP includes extensive troubleshooting instruction for correcting this problem at the following link:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00095908&lc=en&dlc=&cc=us&product=374568

Hope this helps... their support site has been very helpful to me in on several

occasions.

Hello sir, good day, If you cannot print black ink on paper even with new cartridge on the machine, the cradle is dirty, the thing that holds your ink cartridge.

The ink flow is from the cartridge to the cradle then to paper, check the cradle, for proper cleaning.

Resolving a blinking light When an error occurs, the power light will blink continuously and an error message will appear on the computer screen. Read the onscreen error message explaining the problem and follow its solution. If no error message appears, go to the Maintenance section in the Printer Assistant and click any of the four main buttons. This will prompt the software to check the status of the printer and the error message should then appear. The following table lists possible causes and what to do to correct the problem. Symptom Possible cause What to do to correct the problem Power light is blinking Printer cover is open Close the cover. Printer is out of paper Insert appropriate media in the In tray. Printer has difficulty picking up label media

• Change the printers print mode setting.
• Change the printer's paper type selection.
• Use a different brand of label media.

There is a paper jam Follow each of these steps until the problem is resolved:

1. Remove the paper from both paper trays.
2. Press the Power button once. Wait a moment for the paper jam to clear.
3. If printing labels, verify that a label did not become detached while passing through the printer. If the paper jam was not resolved, continue on to the next steps.
4. Remove the rear access door.
5. Remove the paper jam through the opening at the back of the printer.
6. Replace the rear access door.
7. Reload the paper into the paper In tray.
8. Print the document.

There is a problem with a print cartridge Follow each of these steps until the problem is resolved:

1. Remove and then reinsert the print cartridge(s) into the printer.
2. Clean the print cartridges automatically using the Clean Cartridges option in the Printer Assistant.
3. Manually clean the print cartridges and print cartridge cradles:
   • Open the printer cover and wait until the carriage moves to the center.
   • Press the Power button to turn off the printer.
   • Disconnect power cord from the back of the printer.
   • Remove the print cartridges and place them on a piece of paper with the nozzle plate facing up.
   • Lightly moisten a cotton swab with distilled water.
   • Clean the face and edges of the print cartridges with the swab. Do not touch the print cartridge ink nozzles or copper contacts.
   • Wipe the underside of the print cartridge cradle walls using a clean, moistened swab.
   • Reinsert the print cartridges.
   • Close the printer cover.
   • Connect the power cord to the back of the printer.
   • Press the Power button to turn on the printer.
4. Calibrate the print cartridges.
5. If the light is still flashing, replace the print cartridges.

Power light is blinking and/or there are missing lines or banding issues on the printout The print cartridge has partial loss of electrical interface with the carriage connections

1. Print a printer self-test by holding the power button down with a pencil and opening and closing the top cover four times.
2. Check the nozzle self-test pattern in the self-test print out. If one or more of the solid rectangular areas are missing, an electrical contact problem may be present.
3. Remove and then reinsert the print cartridge(s) into the printer.
4. Print the document.
5. If the problem persists, follow the steps listed above for cleaning the print cartridges and print cartridge cradle.
6. Try printing again. If the problem continues, replace the print cartridges.

Have you removed the tear off tape from top of cartridges, it lets the air in and ink flows.

Try going to the Dell site and searching for that printer model. Then see if you need to have both ink cartridges populated and filled with ink, to make it work.

You might also clean the contacts on the ink cartridges, to make sure the printer knows you have both cartridges in the printer, even though they're not both filled with ink.

It just might require both to be filled, before it will print for you.

See what Dell says.

Good luck.

-a.

Step1
Turn the printer off and on to see if it can automatically clear some or all of the jam. Many printers provide an error-code listing on the front panel display for the area where the jam occurred. If your printer shows an error code, be sure and check the printer manual to see if that identifies the area of the printer where the jam occurred. 
Step
2
Turn off the printer. 
Step
3
Remove any paper trays. Inspect them for wrinkled or damaged paper. 
Step
4
Open any other doors that give access to the printer's paper path and to the toner or ink cartridge. 
Step
5
If necessary, remove the toner or ink cartridge. Place it in a bag or away from light to avoid damaging it. 
Step
6
If you find a piece of jammed paper, remove it by holding it with both hands and pulling firmly (see A). The goal is to keep the paper from tearing. If several pieces are jammed together, try pulling out the middle piece first to loosen the jam. 
Step
7
If the paper does tear, try rotating the roller gears manually to free the paper (see B). Don't force anything, though. 
Step
8
Replace the toner or ink cartridge and paper trays, close any doors you opened and turn the printer back on. 
Step
9
If the printer paper jam message still appears, then there is still some paper in the printer. Reinspect the paper path.

hi!

Try to cancel your document in the printers menu even if you restart the pc or the printers memory stores the previous command.

1.The idea is that printers has its own memory unless you cancel the document that you print.

e-mail me at wendel_tenebroso@yahoo.com if the problem persist

The E usually represents paper jam
unplug from wall socket and then replug and try printing