Question about GPS

2 Answers

Hi. I have a Standard Horizon CP180i. The GPS powers on, but I can barely see the screen. What can I do?

Posted by on

  • bmm2170 Sep 05, 2009

    I don't think the projection screen failed, I do see some image.

  • bmm2170 Sep 05, 2009

    No, not partial vision, the whole screen is dim, but there is an image on the screen. Do you know where I can get this device serviced?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,511 Answers

Hello,
If the GPS plotter can be reset if you are facing unpredictable status. You need to reset the RAM or you can simply remove power from the battery for a few time and then re insert it.
Hope this will work.

Make sure that you are properly operating the device, failing to which may cause trouble.
Following is the link from where you can download the user manual of the device. Make sure you have properly configured the device according to the official specs.

http://www.standardhorizon.com/indexVS.cfm?cmd=DisplayProducts&ProdCatID=84&encProdID=491E084FB06B41812BEEF96C77A4A8E2&DivisionID=3&isArchived=0&currTab=tab_Description&currDiv=DescriptionDiv&ExpandID=713,Features


If the problem persists, You can made a claim to the company for the repairing/replacement of the device. This device comes with 3 Years warranty. If your device's warranty is valid then you can make a claim for it by delivering the product to the below stated address.

STANDARD HORIZON (Marine Division of Vertex Standard)
Attention Factory Service-
10900 Walker Street
Cypress, CA 90630.


Kindly do rate me if I'm Helpful.
Regards.

Posted on Sep 05, 2009

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Contributor
  • 430 Answers

I think the projection screen has failed. Try Replacing it.

Posted on Sep 05, 2009

  • Nandini Dhar
    Nandini Dhar Sep 05, 2009

    If there is patial vision, then some parts of the projection board has failed. Please check it.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

What do you mean by hold the bottom right corner of the screen. It isnt a touch...


1- Turn off unit.  2- press and hold the bottom right corner of the screen. 3-While still pressing and holding bottom right corner, press and hold power button and continue holding both until a white screen appears with a black dot. 4- follow the on screen directions and your unit will be back to the day you first got it.

on Jul 25, 2008 | Garmin StreetPilot C330 GPS Receiver

1 Answer

I need an operating manual for a Standard Horizon CP155c chartplotter


please call Standard Horizon Marine Support 800-767-2450 and they will email you the manual.

marinetech@vxstdusa. com

Sep 10, 2010 | Standard Horizon CP155C GPS Receiver

1 Answer

Standard horizon 155c not acquiring signal


If the signal is good statement seems to imply that it is working, perhaps this is my misinterpretation of what you mean by this.
Signal refers to the abi;ity to connect to satellites
4 are requied for triangulation.
If the unit is fully charged and not connecting , then it is quite possible that the unit has a damaged SIIRF chip or whatever chip was used in your model to acquire satellite connection. The cost of repair is costly, it means total replacement of the M/Board.
Never start car with the unit connected into DC car power, spikes will damage the chip

Jun 30, 2009 | Standard Horizon CP-150 WAAS GPS Receiver

1 Answer

I am trying to delete all tracks/routes on CP180 Standard Horizon


reading your owners manual (link provided at below) , i see you can delete / edit points one at a time or a faster way format the C Card.

** formatting the c card instructions >

1.) press MENU , move the shuttle point knob to highlight USER POINTS , and press ENT .
2.) move the shuttle point knob to highlight USER C CARD, and press ENT .
3.) move the shuttle point knob to highlight FORMAT ,
and press ENT .
4.) a popup warning window will pop up to confirm you want to format the user C card .
5.) select YES , and press ENT to confirm , (select NO otherwise) .
NOTE : formatting the user c card erases all files previously saved on the c card .

CP180 users guide

J5


Jan 17, 2009 | Standard Horizon Chart Plotter CP180 GPS...

1 Answer

Help


supposedly not you only need a card for more detailed maps

Nov 15, 2008 | Standard Horizon CP-150 WAAS GPS Receiver

2 Answers

Power cord


I called standard horizon myself and bought the power cord for $25. The # 714-827-7600

Nov 12, 2007 | Standard Horizon CP150 GPS Receiver

Not finding what you are looking for?
GPS Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top GPS Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

The Knight
The Knight

Level 3 Expert

74136 Answers

kakima

Level 3 Expert

102366 Answers

Are you a GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...