Question about KitchenAid 24 in. KUDS02FR Built-in Dishwasher

Open Question

THe ProScrub light is steady, and the dishwasher does not work. When I push buttons, the light keeps going off, and with the next button push, it goes on. If I leave the dishwasher like this for a while, then a couple of the other lights, I think the Normal and Heated Dry lights will blink continuously. In either state, the dishwasher does not work.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wheelshot
  • 102 Answers

SOURCE: "Normal" light flashes

You need a new control bd. #W10084141. If the diagnostic mode will not work then the board will have to be replaced.

Posted on Apr 01, 2009

  • 56 Answers

SOURCE: the light on the buttons that say cancel and normal are flashing and the dishwasher won't turn on.

first thing to try is to disconnect power for 15 minutes and then try again if goes into default again take off bottom panel and behind the black trim will be a tech sheet see if it gives yousome diagonostics sounds like it may be the computer if the power off and on doesnt make it work,.

Posted on May 31, 2009

  • 1 Answer

SOURCE: whirlpool quiet partner III. Clean light keeps flashing clean.

Had the same problem. Press the sani-rinse and heated dry button back and forth and it should reset.

Posted on Dec 29, 2009

ginko
  • 19396 Answers

SOURCE: I HAVE A BLINKING LIGHT

Hi.

If the button that starts flashing along with China button is the main button, then the problem is a defective button board, and the China button switch gets stuck causing the error. The button pad is separate from the control module.
The problem is usually fixed replacing the button pad.

Parts and diagrams can be obtained entering the full model number here.

Regards.

Ginko.

Posted on Dec 03, 2010

Daniel S
  • 4323 Answers

SOURCE: The clean light keeps blinking

Hi

If clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To resolve this error try pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air Dry - High Temp - Air Dry or Hi Temp Scrub, energy saver dry, Hi Temp Scrub, energy saver dry. Now let the unit run for 2-3 minutes and then you press the Cancel/Drain button and allow it to completely drain and reset.
If this doesn't work then it's an issue with the wash pump not pumping the water past the heater efficiently or due to lack of water to heat. Please make sure that heater is not open circuited and is heating the water efficiently. You'll have to check the heater using a multimeter; the meter should read between 3000 to 3300 ohms (Use multimeter on Rx1 ohm setting). If heater is fine then make sure water pressure is optimum and fill valve is working fine. Hope this helps... Please post back for further assistance.

Daniel

Posted on Jan 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MY KITCHENAID DISHWASHER FAILS TO POWER OFF


Programmer fault.......time for repair man or replace machine. I assume out of warranty.

Jul 21, 2014 | KitchenAid 24 in. Built-In Superba Series...

1 Answer

Lighted "3" shows, dishwasher won't start


PRESS AND HOLD THE BUTTON NEXT THE LOCK3 LIGHT FOR 3 SECONDS TO UNLOCK THE CONTROL PANEL. TO RELOCK THE CONTROL PANEL PRESS THE SAME BUTTON FOR 3 SECONDS. THANKS AGAIN

Apr 20, 2014 | Maytag MDB7100AWB Dishwasher

1 Answer

Maytag dishwasher MDB-8 shows "3", won't start.


click this link for the service manual, check page 5 for error codes, http://servicematters.com/maytag_library/docs/16026393.pdf this also tells you how to put this in diagnostic mode. hope this helps.

Apr 20, 2014 | Maytag 24 in. MDBH970AWS Built-in...

1 Answer

Programing garage door opener


You push the button that has the house design on it. It should change from steady to blinking. When it does you hold the garage door opener next to the blinking light and keep the button pressed on each. When the new code is learned the car button should indicate it learned the new code.

The you just press the button on the visor to see if it will work.

Mar 27, 2010 | 2007 Mercury Mountaineer

1 Answer

Kenmore Ultrawash dishwasher Model 665 15810000. Originally "water heating" light was flashing and no water in dishwasher. Replaced water inlet valve. Turned power back on, normal wash light goes on...


lock light is locking the panel push this child lock button for 3 sec and see if it un locks . then try it again .. may have a pannel out. mm

Dec 06, 2009 | Washing Machines

2 Answers

Lock Light Blinking


silly question but did you try holding the control lock button(perhaps its the heated dry button) in for 3 secs???? sonds as if the CONTROL LOCK has benn activated( child lockout)

Jan 14, 2009 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Cancel light and rinse only light keep blinking and wont start


Hello,

Hopefully you have resolved your issue. I have not heard of the cancel light flashing issue. I have had problems with the clean light flashing seven times over and over and the control panel will not operate. Here is the solution to that. Maybe it will work for your issue as well.

Open dishwasher door,
Push Hi Temp Scrub button,
Push Saver Dry button,
Push Hi Temp Scrub button again,
Push Saver Dry button again,
All lights on control panel will come on.
Close dishwasher door,
Push Baked on Cookware or Normal Button.
Dishwasher should start and complete cycle.

It is good if you have kids that play video games. Their fingers are used to pushing buttons quickly. I guess this resets the control board. The service guy let me have this info as I used to deliver appliances and work on them somewhat.Hope this helps.

Good Luck,
Tom

Nov 26, 2008 | KitchenAid 24 in. KUDS01FLSS Built-In...

2 Answers

DISHWASHER LOCK


I too had the same problem,,and tried it again,,,and it worked for me,,i pushed the button next to the lock light it blinked and i kept holding in the dry button and the lock went off,,,,good luck

Aug 15, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
KitchenAid 24 in. KUDS02FR Built-in Dishwasher Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Dishwashers Experts

Mike

Level 3 Expert

4336 Answers

Cindy Wells

Level 3 Expert

5096 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Are you a KitchenAid Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...