Question about Copystar CS-1815 Printer

1 Answer

Locate cover hinges for CS1820 PRINTER MFG# 06F02R(RIGHT) O6F02L(LEFT)

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Copystar Master
  • 1,447 Answers

Please you follow your printer user manual or brows www.kyocera suppor/documentation

Posted on Sep 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Item comes with right hinged door...I need left hinged door.


On some models you can move the hinges and door pull to the opposite side. On the side without a hinge, you would see plugged holes (plastic plugs covering the holes). You may have to move the top right hinge to the bottom left and bottom right to the top left (opposite of this for a left-hinged refrigerator/freezer).

You may need help to do this, and be careful.

Donald

Jan 27, 2016 | Refrigerators

1 Answer

How to install transferbelt


  1. Remove or slightly pull out Tray 2 (RM1-1916-000CN).
  2. Remove three (3) screws, two (2) from the right cover assembly and one (1) from the left cover

    assembly.

  3. Open the front door
  4. Remove the right cover (RM1-1858-000CN), carefully twisting the front edges of the side covers

    outward to remove.

    NOTE :

    To make the removal of the right cover assembly easier, release the tab on the inside of the cover.

  5. Remove the left cover.
  6. Squeeze the white link lever on the left side.
  7. Remove the screw on the right white plastic catch, and then remove the plastic catch.
  8. Close the ETB.
  9. Remove the small black cable cover (RC1-5147-000CN) on the left side of the printer by carefully snapping it out of place.
  10. Remove one (1) grounding screw from the ETB harness.
  11. Pull out the white wire holder by pushing it up.
  12. Pull out the ETB connector.
  13. Remove one (1) screw from each hinge cam on both sides.
  14. Using needle-nose pliers, remove the hinge left cam (RC1-4249-000CN) and the right hinge cam (RC1-5311-000CN).
Remove the ETB. Use the following procedure to replace the ETB.
  1. Align each foot of the ETB with the respective holes, securing the right side first, and then the left side.
  2. Complete replacement by following steps 1 through 14 above in reverse order.

NOTE :

When replacing the right cover, align the tabs on the upper edge of the right cover and lower edge of the face-down cover with their respective slots.




;














Nov 19, 2013 | HP Color LaserJet 2600n Printer

1 Answer

I replace the screen on my gateaway mt 6916 and cant install the video controler driver


Instructions

1

Prepare the laptop for disassembly. Shut down the laptop completely, then wait a few minutes before removing the battery and unplugging the AC adapter. Turn the laptop over and lay it down on a flat surface so that the battery area is facing away from you and the hard drive is located at the bottom left corner.
2

Remove the hard drive cover. Remove the two screws located on the left side of the hard drive cover, then lift the cover to remove it completely from the unit.
3

Remove the memory cover. Unscrew the eight screws holding the memory board in place; this cover is located above the Gateway product sticker.
4

Disconnect the Wi-Fi adaptor. Remove the Wi-Fi cover by unscrewing the single screw holding the Wi-Fi adapter in place; this is located directly above the hard drive. Remove the two cables connecting the wireless card to the adapter and snap the card out of the holder.
5

Remove the memory modules. Gateway computers typically have two memory modules located in the center of the motherboard; lift these out gently with your fingers and set them aside.
6

Release the heat sink. Unscrew the four screws around the heat sink assembly; this unit is located to the left of the ventilation fan and is surrounded by a copper base. Carefully lift the heat sink and the cooling fan off the unit and unplug the cable attaching it.
7

Remove the CD/DVD drive. Unscrew the small screw located to the left of the CD/DVD drive, then push the drive out to remove it from the laptop completely.
8

Remove all screws around the base of the laptop. You will now be left with a total of 18 screws located around the edge of the base of the laptop, and in between the stickers and hardware components in the center. Remove all of these carefully and set aside in a safe place.
9

Prepare the cover for removal. Turn the laptop up on its edge so that the back of the laptop is facing you; you will see two screws on the hinges of the computer. Unscrew these and set them aside.
10

Remove the hinge cover. Open the laptop so that the screen is laying flat; use the flathead screwdriver to pry open the hinge cover and pull it off gently with your fingers.
11

Remove the keyboard. Lift up the keyboard and reach behind it to release the cable. You will need to tug gently on the cable to unhook it from the motherboard.
12

Unhook the LCD screen from the notebook. Unplug the Wi-Fi antenna cables located on the right side of the motherboard directly under the screen, then unplug the video cable located directly under the hinge cover. Remove the pair of screws located to the left and right of the LCD screen and gently lift the LCD screen off the notebook's base unit.
13

Remove the system board. Turn the base unit over and unscrew the five screws securing the motherboard to the base. Two of these are located near the hinge cover, and two are located beneath and to the right of the hard drive unit. The fifth is located a few inches below the top right edge of the laptop.
14

Disconnect the motherboard. Lift the system board, then unhook the cable connecting it to the base unit.

Jan 10, 2013 | Gateway DX4200-09 PC Desktop

2 Answers

Left hinge broke on lexmark pro 905


Not a perfect fix, but this is what I did: There are 2 spring-loaded pistons located on the printer side of the hinge that cause this problem. I think there should be another piece of plastic that holds the top of the printer hinge down on these springs, but when this hinge is gone, the top of the printer is held upward by them. If you use some pliers to gently pull these spring-loaded pistons upward, you can easily pull them out, followed by the springs they cover. Once removing these, the top of the printer lies flat. The top is still unstable, but mine will now feed paper just fine and closes. Hope this helps! WebRepOverall ratingThis site has no rating(not enough votes)

Oct 23, 2012 | Lexmark Platinum Pro905 multifunction...

1 Answer

How to replace the roller



  • Tray 1 Pickup Roller Replacement
  • Turn off the printer and unplug the unit. Remove the following doors: the DIMM cover, rear cover and top cover.
  • Open the door to the area housing the toner and remove the toner cartridge. Set it aside. Release the toner drive arm located at the right side of the toner door.
  • Locate and remove the screws at the front left and right corners on the top of the printer and the two screws at the right and left at the top of the back of the printer.
  • Locate the latch at the left side of the hinge for the toner door. Release this latch and then remove the door.
  • Pull out the old pickup roller and replace it with the new tray 1 pickup roller. Reassemble the printer.
  • Feb 21, 2011 | HP Office Equipment & Supplies

    1 Answer

    How to exchange the ETB unit (belt) on a HP Colorlaserjet 2600n?


    To replace the ETB Belt.. follow this step..but it would be easier if I can show u the diagram.. I will figure a way to upload. but let see if u understand here...
    ETB removal and replacement
    Use the following procedure to remove the ETB (RM1–1881–000CN).
    1. Remove or slightly pull out Tray 2 (RM1–1916–000CN).
    2. Remove three (3) screws, two (2) from the right cover assembly and one (1) from the left cover
    assembly.
    3. Open the front door.
    4. Remove the right cover (RM1–1858–000CN), carefully twisting the front edges of the side covers
    outward to remove.
    NOTE : To make the removal of the right cover assembly easier, release the tab on the
    inside of the cover.
    5. Remove the left cover.
    6. Squeeze the white link lever on the left side.
    7. Remove the screw on the right white plastic catch, and then remove the plastic catch.
    8. Close the ETB.
    9. Remove the small black cable cover (RC1–5147–000CN) on the left side of the printer by
    carefully snapping it out of place.
    10. Remove one (1) grounding screw from the ETB harness.
    11. Pull out the white wire holder by pushing it up.
    12. Pull out the ETB connector.
    13. Remove one (1) screw from each hinge cam on both sides.
    14. Using needle-nose pliers, remove the hinge left cam (RC1–4249–000CN) and the right hinge
    cam (RC1–5311–000CN).
    15. Remove the ETB.

    Use the following procedure to replace the ETB.
    1. Align each foot of the ETB with the respective holes, securing the right side first, and then the left
    side.
    2. Complete replacement by following steps 1 through 14 above in reverse order.
    NOTE : When replacing the right cover, align the tabs on the upper edge of the right cover
    and lower edge of the face-down cover with their respective slots.

    May 23, 2010 | HP Color LaserJet 2600n Printer

    2 Answers

    Brother 8820d MFC auto doc feeder does not work...


    You need a new hinge so the cover will sit down properly, or paper will jam anyway, but it sounds like there is still a scrap of paper on one of the sensors inside the ADF, you need to look with a flashlight down thru where the paper goes and also look up thru the slot with the ADF lifted.

    Sep 11, 2009 | Brother MFC 8820D All-In-One Laser Printer

    2 Answers

    Parts for Brother MFC 8200D


    Yes, I had the same problem in Sept 2006 - a broken left hinge that needed fixing. Ordering the part was easy. I was able to install it myself, but it required some attention to detail.

    I called Brother International at 800-284-4357, Option 1, then 2. I ordered the left hinge - Part No: LP-2403001 - described as ADF Hinge Assembly (left). If you broke the right hinge, the part number may differ slightly, but person on phone should be able to assist. It cost me $11.55 including shipping.

    Feb 28, 2008 | Brother MFC 8820D All-In-One Laser Printer

    2 Answers

    My MFC8440 Cover Left Hinge Brocken


    Very common part any brother dealer can get it. Ring brother to find closest dealer about 20 bucks

    Dec 06, 2007 | Brother MFC8440 Remanufactured Laser...

    Not finding what you are looking for?
    Copystar CS-1815 Printer Logo

    Related Topics:

    179 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Copystar Office Equipment & Supplies Experts

    Kyocera HP Expert

    Level 3 Expert

    523 Answers

    CheckitRight
    CheckitRight

    Level 3 Expert

    1362 Answers

    Tammie Duggan
    Tammie Duggan

    Level 2 Expert

    38 Answers

    Are you a Copystar Office Equipment and Supply Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...