Question about KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

5 Answers

Maytag Quiet Series 300

Dishwasher started last night, but cut off after water filled bottom. When you push buttons there is no power.....no lights comes on. We checked electric source and power is available, but it will not turn on. Any ideas?

Posted by on

  • 6 more comments 
  • Anonymous Mar 11, 2008

    I have same problem,repairman came today and said he thinks it's the control panel but can't find the model # so he can;t order the part.Where is this fuse located?

  • sjue Aug 04, 2008

    The dishwasher would work intermittently. The front panel switches seemed to be the problem. I replaced the front panel, it worked for about a month, and now seems to be worse than before. The start switch has been dead for a week. Is it potentially the control board? I'm debating on ordering a control board ~$80 or buying a new dishwasher (not maytag). It is about a $450 machine, and I've already got about $170 trying to repair between part and service call. Should I cut my losses and buy another or try control board.

  • Erin Meisner
    Erin Meisner Oct 07, 2008

    it is definitely the control panel. This is covered under warranty.

  • edp232 Oct 18, 2008

    My 2 year old Maytag just die. The control panel stops working for almost a month. Since I don’t plan to keep this washer (takes too long to wash, rusty screws inside), I took it apart to see if any thing obvious. I was surprise to find a whole family of small roaches living inside the circuit board housing. The roach drop covered many circuitries. I suspect that's what shorted out the machine. Also, I found the circuit board has a thin layer of clear coating that’s start to flake. I wish Maytag will do a better job sealing the circuit housing.

  • ccjuno Nov 09, 2008

    Same issue here too.Where is one of the best internet sources for thermal fuses for Maytag dishwashers?



    Another thought is the Home Warranty policies can sometimes be economical in my past experience but have a $50.00 deductible per call and range from $250(just kitchen appliances) - $475 for whole house/ AC and sometimes even septic coverage.



    Thanks,

    ccjuno

  • Anonymous Mar 27, 2009

    The start button won't work, all the others will.

  • Anonymous Apr 27, 2009

    I also have the Maytag Quiet Series 300 and it keeps water at the bottom rather it runs or just sits there.




  • danielsrodan
    danielsrodan Feb 24, 2013

    I have a Maytag Quiet series 300 circut breaker tripped cut power to disposal and dishwasher, turned on the circut breaker disposal works but the washer won't power up.

×

Ad

5 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Sounds like a thermal fuse that is a less than $20 part. remove the top 6 screws in the door that hold the plastic front panel on. Behind that is a circuit board and a white flat 1" square fuse with two wires going to it. make sure power is off at breaker. Test with an meter to see if any current is going thru. If not, that is most likely your problem, and just follow the fuse replacement kit instructions carefully, including putting the new wires on the new fuse like they say. Otherwise, the original wires going to the fuse will blow it too.

Should take about 20 minutes.

Posted on Feb 12, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

You might want to check the float, it might have gotten stuck, it is the round thing in the corner.

Posted on Dec 09, 2007

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

The problem is with the circuit or control board (not sure of the name), which is covered in the warranty (it was for us). The whole piece that holds all the buttons for settings comes off and is replaced by a new one. Then all power is restored and everything works (the question is.. for how long?).
I went directly through Maytag and they will look up the warranty info etc.
Good Luck

Posted on Jan 29, 2009

  • Erin Meisner
    Erin Meisner Jan 29, 2009

    Our dishwasher wouldn't drain and my husband found there was a clog in the plastic drain tube, under the sink, connecting to the main drain. He squeezed it and bent it a few times where he felt the clog, we then plunged the sink and in a minute or two we turned the dishwasher back on and it drained.

    Good Luck

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I was able to get mine going just like new by replacing the switch panels on the front and top of the door. This model is prone to water intrusion into the panel switches due to unsealed gaps between the panels and the door housing. This causes a variety of problems and symptoms depending where the water gets in.. Mine was stuck on quick wash and didn't clean dishes very well.. I tore it apart and found a lot of water under the panel and corrosion on the ribbon cable that connects the switch panel to the control circuit board. I took a chance and ordered the $90 switch panel because it looked pretty bad. (Pics attached) The control board looks brand new and was replaced with the switches 4 yr ago under warranty. Before I installed the switch panels I put a bead of silicone around the edge of the switch panel to fill in the gap and keep water out. It's a pretty good dishwasher with a stainless tub and 4 washer blades. After the fix all the modes work and it cleans very well. I'm hoping it will last a long time with some minor maintenance. Best wishes to all. Here's a link I used as well. http://www.gcsdblogs.org/roodhouse/?p=728
Maytag Quiet Series 300 - 778a617f-8eb6-4600-b8b4-e22c35ff287a.jpg397b89c2-25c8-4de1-b551-30d9117298a1.jpgc1a083c1-6f81-4bf4-af46-c1f743ae9cf1.jpg

Posted on Dec 16, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a (6 mos old) Maytag QuietSeries 300 that was not draining. I found this out after I had to replace the garbage disposal. The dishwasher has a small accordion-like hose that leads to the garbage disposal for draining. I detached the hose from the garbage disposal and pushed it back through the cabinet to try to release any plugs or crimping. Leaving it unplugged, I pointed the hose into a large pan and closed the dishwasher, and turned it on the "rinse only" cycle. After it started, I hit the "cancel" button. This began the pump to drain the water. It worked! The water began flowing through the hose again! It took 2 pans exchanging water from the hose, but finally drained completely. Hopefully, this will work for you.

Posted on Apr 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just bought a 4 year old maytag 300 quiet series and hooked it up all front buttons light up when you push what you want but will not fill with water. Goes to cycle where water should be spraying around...


Sounds like an internal timer malfunction.
Maytag Customer Service: 1 (800) 344-1274 U.S.
Try to find your model # and serial number if not out of warranty before called.
It sounds as if your machine needs to be inspected by a service repair agent in your area. Maytag can lead you to an authorized local repair man.

Oct 08, 2010 | Maytag 24 in. MDB9750AW Dishwasher

3 Answers

1.5 year old Maytag Legacy Series Quiet Series 300 Lock Light on


Hold down the heated-dry button for 3 seconds and the light will clear.

Nov 07, 2009 | Maytag 24 in. MDB9750AW Dishwasher

2 Answers

Maytag Quiet Series 300 only goes to RINSE ONLY


Try unplugging the washer to reboot the computer board. Sometime power surges at night can cause undervoltage on the board and make it do funny things. Rebooting by removing power for 10 min will drain the board and start with a fresh program. This is true for microwaves, dishwashers, dryers, etc.....

May 08, 2009 | Maytag 24 in. MDB5600A Jetclean II...

2 Answers

Maytag Quiet Series 300 Dishwasher will not turn off after it com


MY DISHWASHER KEEPS RUNNING, IT IS A WHIRLPOOL GOLD QUIET PARTNER IV

Apr 05, 2009 | Dishwashers

2 Answers

Maytag quiet series 300 leaks from front


check the float switch on the righthand side on the bottom in the corner it should click and move freely

Dec 16, 2008 | KitchenAid 24 in. KUDI02IRBS Stainless...

2 Answers

Maytag quiet series 300


Maytag Quiet Series 300. The lights flash in sequence starting from the outside traveling inward. The timer counts backwards from 50 to 1. Then the sequence starts over. and continues over and over. I'm able to clear it when the time reaches 1 or 2. It stays off for a while (3-4 hours) then starts over. I can not clear the countdown until it reaches 1 or 2. After I clear it the dishwasher will work, but until then, no way. This happens with the door open or closed.

Sep 15, 2008 | KitchenAid 24 in. KUDI02IRBS Stainless...

2 Answers

I have a maytag quiet series 300. When it is done with any of the cycles in leaves about 1-2 inches of water in the bottom of the dishwasher. I can manually hit the start button twice and it will go...


Hi jeffwirch,

I'm Harvey the Master Plumber.

Your problem is: You have a maytag quiet series 300. When it is done with any of the cycles in leaves about 1-2 inches of water in the bottom of the dishwasher. You can manually hit the start button twice and it will go through a 2 minute cycle and pump out the water. You have cleaned the filter inside the dishwasher where it drains and have checked the hose to the disposal and it pumps out fine. It just doen't pump itself at the end of the cycle.

It sounds like a bad control board. It's in the top of the door panel. I don't recomend this repair to the average homeowner. You might consider the Repair Directory to find a repairman.

Feel free contact me again!
Please give me a rating here at fixya.com before you sign off
Thank you,
Harvey your Master Plumber

Sep 13, 2008 | Maytag Dishwashers

1 Answer

Maytag Dishwasher Quiet Series 200


The 3 symbol on the face control panel light is on and starts flashing anytime you push any other button, and is full of water in the bottom of it. My wife says she stopped the washing cycle a couple of days ago but now it wont start back up.
This is a Maytag series 200

Mar 15, 2008 | Dishwashers

1 Answer

MayTag Dishwasher Quiet Series 300


If it is not filling enough, you may need a new water valve. It may be plugged.

Nov 19, 2007 | Dishwashers

Not finding what you are looking for?
KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher Logo

8,341 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Mike

Level 3 Expert

4349 Answers

Cindy Wells

Level 3 Expert

5416 Answers

Are you a KitchenAid Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...