Question about Coffee Makers & Espresso Machines

1 Answer

How to change blade on bosch jigsaw GST 80 PBE

DONT KNOW HOW TO CHANGE A BLADE ON BOSCH JIGSAW GST 80 PBE, USALLY A SCREW OR ALLEN KEY BUT CANT FIND ONE. PLEASE HELP!!!

Posted by on

  • Anonymous Jan 17, 2009

    yes

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I just bought a used one and faced the same problem. What I found in there is a set screw at the bottom of the long shaft. I used a long narrow flat head screw driver. It worked good, but I did have to acuate the trigger to get it the blade near the top of the stroke

Hope that helps.
AG
Porsgrunn Norway

Posted on Aug 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove blade wont budge with allen key


Hallo Ingrid
Pl send a picture Of allen bolt , if possible make a flate cut with hacksaw and open with screw driver.

Jayesh Desai

Jul 16, 2014 | Makita Jigsaw Blade

1 Answer

Change blades bosch jigsaw


The one shown in the picture uses a very long and thin, flat blade screwdriver. There is a set screw that puts tension on the blade when the screw is tightened. Bosch sells the correct screwdriver or you can buy a long one and grind the sides down a bit. That's what I did.

May 17, 2012 | Bosch GST80PBE JIG SAW FOR 220 VOLTS

1 Answer

How to tighten shoe bevel lever


You need to use an allen key or allen wrench (metric) to fit the screw in the center of the footplate.
See the online instruction here for details. Bosch used to provide one with the saw that was slotted into a plastic holder on the cord, but if you don't have that you'll have to find a 5MM allen wrench.
I know your post is quite dated now, but hope this is helpful nevertheless.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Jun 08, 2011 | Bosch 1587avsp Vs Orbital Jigsaw

1 Answer

How do i change a blade for my jigsaw pst 50a


there should be a allen head bolt in a slot at the top of the blade. you loosen it and pull out blade , replace blade and tighten bolt back up. hope this helps. have a good day,

Jan 08, 2011 | Bosch 24V Jig Saw W/ 2.4 A H Battery...

1 Answer

I have a bosch 1587 vs jig saw i got used. I don't know how to install a blade. I have never had one like this. I turned the top handle the way the diagram showed but I don't think something is working.


In most models at the blade shuck holder is a screw that thigh the blade,unscrew it and change your new balde .
Also Go to this LINK and find the part/diagram that can help you.

Please thumbs back if help is fine,thanks!.

Nov 02, 2010 | Bosch 1587avsp Vs Orbital Jigsaw

1 Answer

DROPPED MY BOSCH 1590EVSK JIGSAW, REPLACED BENT BASE, BUT BLADE IS STILL NOT PERPENDICULAR TO BASE. CAN'T SEE ANY ADJUSTMENT METHOD TO ALIGN BLADE PERPENDICULAR TO BASE PLATE. HELP


The socket-head screw that holds the sole plate on is also the alignment screw. Loosen it a little and the sole plate will swivel left and right. There are graduation marks on the base to help with alignment but I always use a square to verify the alignment. Tighten the screw and check again that it didn't move and you are ready to go.

Aug 20, 2010 | Bosch 1590EVSK 6.4 Amp Top Handle Jigsaw

1 Answer

Bosh pst54e instrution manual how to remove blade


Hi just wondering what the screw looks like as I have an old one of these that the screw went missing out of years ago. I'd like to replace it but need to know length and diameter of the screw if you could please?

Feb 11, 2010 | Bosch Saws

2 Answers

Changing the blade on my Bosch GST 2000


lift knob on top twist 3 times anti clockwise remove blade by twisting it 90 deg insert new blade turn 90 deg,turn knob on top clockwise until it clicks press down and you are ready to go

May 16, 2009 | Bosch #T101A3 3PK 4" 14TPI Jig Blade

2 Answers

Cant change a blade on 500watt pendulum jigsaw fmtc500js


Hi

There is a click mechanism to replace the blade at the top of the blade.

best regards savumihai71

Jan 18, 2009 | Saws

Not finding what you are looking for?
Coffee Makers & Espresso Machines Logo

Related Topics:

3,399 people viewed this question

Ask a Question

Usually answered in minutes!

Top Coffee Makers & Espresso Machines Experts

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Marvin
Marvin

Level 3 Expert

83096 Answers

Kolbrun...

Level 3 Expert

1215 Answers

Are you a Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...