Question about Scanport 17" LCD Monitor

Open Question

Signal Out of Range message

This message happens even at startup. I've tried changing the resolution and frequency settings and changed my video settings in bios to 128mb. I also tried hooking it up to another desktop (HP) and that computer beeps like crazy at startup. I haven't tried out a new cable yet, but I did ohm the pins out. Not sure what else to try unless I need a new video card. I'm running an AMD 900mhz processor with 1gb ram. Windows XP Home edition. Currently using a CRT monitor that works fine. Thanks

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 62 Answers

SOURCE: ''out of frequency range'' on crt monitor

Go into your "Device Manager" in Windows and find out if your HDTV monitor is still installed. Delete the settings under the monitor tab and reboot the computer. With any luck the reboot will cause Windows to re-detect your current monitor and install the proper settings. A similar process may need to be followed with your video card driver as well. CAUTION: Make sure you have a disk or some means of installing a copy of your video card driver before you delete out the currently installed one.

Hope this helps!

OpenSource13

Posted on Apr 05, 2009

Ad
micromend
  • 748 Answers

SOURCE: LCD Monitor (Model Number M17FBA) Signal Out of Range

Hi
Start the computer in SAFE mode. F8 before Windows starts. Once in SAFE mode change the screen resolution to 600 X 480. Do this by right clicking anywhere on the desktop. Once done then reboot into normal mode.

Posted on Jun 03, 2010

Testimonial: "Very detailed yet very concise and reader-friendly response, and in less than 4 hours! Unbelievable."

  • 1768 Answers

SOURCE: frequency out of range

the monitors resolution range is only to 1280X740 or 780
and your video card may also need an upgrade.
The game may require a higher resolution that is not compatible with the the devices mentioned.

Posted on Jul 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Compaq Presario pops up a system boot menu everytime at startup.


This comes up mostly when it requires a BIOS save. Try that. If that does not help, sometimes setting the default settings and saving will help.

Dec 04, 2012 | Computers & Internet

Tip

Fixing 'Out of range', 'Format not supported' message


When the video card signal exceeds the frequency allowed for the monitor, the following error message may occur:
Sync out of Range, Out of range, Format not supported
SOLUTION (FROM HP):
To avoid the message, lower the resolution or vertical frequency of the video card.
Reboot the system and use the VGA mode to force the video card driver to lower its resolution. Follow these steps.
1. Shut down and restart the system.
For consumer systems such as HP Pavilion desktop PCs, push the Power button once.
For commercial systems such as HP business desktop PCs, hold down the Power button for five seconds.
2. Immediately after seeing the HP/Compaq logo screen, press F8 at system startup to initiate the bootup menu.
3. Scroll down to highlight Enable VGA Mode , and press ENTER .
4. After Microsoft Windows completes its bootup process, access the Display Properties and select a desired resolution, which is compatible to the connected monitor. Reboot

Resolution adjustment:
From Microsoft: http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/display_change_screen_resolution.mspx?mfr=true

and here:
http://www.helpwithpcs.com/tipsandtricks/changing-screen-resolution-win-xp.htm

and here:
http://www.videojug.com/film/how-to-change-screen-resolution-in-windows-xp-and-windoiws-7

on May 21, 2010 | Computers & Internet

1 Answer

Dell 8400 No Boot, not even POST


It sounds like your bios were improperly flashed or went bad. The X300 SE message is your video card. So your video card works, the system mostly works, but the BIOS isn't starting up. You should contact Dell and tell them the situation.

Apr 19, 2010 | Dell Dimension 8400 PC Desktop

1 Answer

My computer screen has error message Frequency out of range. This happened when running Google Earth, it changed the color quality from 32 bit to 8 bit. When I tried to change the bit back I get this error...


Right click on the free space in the desktop and select properties. Then go to display properties and change settings to 32 Bit and Change the screen resolution to 1024 by 768 Pixels.

Apr 05, 2010 | Gateway GT5220 PC Desktop

1 Answer

GX520 screen display message: cannot display this video mode


This means that the windows setting you have set can not display on your current monitor. There are two ways to fix this, one is to boot the computer in safe mode by pressing f8 after the POST screen and change the resolution and the other is to plug the computer into a different monitor to see if supports that resolution and then change the resolution in windows to a lower setting.

In case you don't know how to change the resolution in windows, follow below.

Right click on the desktop
Properties
Settings at the top
Move the slider to 1024x768
Click ok

Try rebooting. If that still doesn't work, try another resolution.

Oct 19, 2009 | Dell OptiPlex GX520 PC Desktop

1 Answer

THE VGA PORT DOESNT SEEM TO BE ACKNOWLEDGING THE COMPUTER OR VICE VERSA. ACTUALLY, IT DOES RECOGNIZE IT BUT THERE ARE NO DRIVERS FOR IT , ANYONE KNOW WHERE TO GET THEM


You need to give more information about your set-up for help. What type of computer are you using and what operating system.What type of graphics card. All of these systems have to be compatible with the television input for you to get operation. I found this in the appendix of the owners manual on PROSCAN website. www.oncorpus.com. The customer service telephone for PROSCAN is 1-888-977-6722 The PC Screen continually appears and disappears.
Check the connection between the TV and the computer and see if the connector is locked.
􀁺 A “There is no signal “message appears.
This happens if the signal from the video card is exceeded for the maximum resolution or frequency of the TV. Try to set the
maximum resolution or frequency for the TV.
See if power save mode of the PC functions properly.(This is deactivated when any key is pressed or the mouse is moved)
􀁺 The screen looks like there is water flowing on it.
Check the connector connected to the TV.
􀁺 The screen is unclear and blurry.
Change the frequency and phase adjustment. Change the Resolution and frequency to the standard limit.
􀁺 Unstable and flickering screen.
The resolution and frequency of the PC's Graphics Card should be set within the TV's range. Check the TV menu’s current
mode and standard mode and set it up again.
􀁺 Some modes in standard mode are not working.
Check the compatibility of the video card.
If it is not working for compatible hardware, try to upgrade the driver of the graphics card

May 09, 2009 | Proscan 26LB30QD 26 in. LCD HDTV

2 Answers

Can't change the resolution


The frequency failure is probably a message from the monitor to say it cannot cope. When setting resolution click "advanved" and try reducing the frequency.

Apr 30, 2009 | GE Asus P4GE-MX...

1 Answer

GeForce 6200 PCI when drivers are loaded, screen goes blank


the problem is with display resolution setting which ur monitor doesnt support

press f8 on startup and choose enable vga mode

then widows will boot up in 640x480 mode

then change the resolution to 800x600 or whatever u want

thanks

Apr 11, 2009 | XFX NVIDIA GeForce 8500 Graphic Card

1 Answer

Monitor displays Msg. frequency out of range, screen is black


Start your computer and press the F8 when the manufacturer's logo screen is showing. This will bring you to the Windows startup menu. Pick "start in VGA mode" and windows will start up with video settings you monitor can handle. Then you can change your video settings so Windows will start normally with your monitor.

Mar 31, 2009 | Compaq Computers & Internet

10 Answers

Monitor is working out of scan range


It probabily happens after you change the settings of display in control panel (windows), if so restart the machine and press function key <F8> after memory test and you shoud get to the startup menu, choose VGA mode and undo the changes in display that you have made.

Best Regards

Creon

Mar 30, 2006 | Dell P780 17" CRT Monitor

Not finding what you are looking for?
Scanport 17" LCD Monitor Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Scanport Computers & Internet Experts

William Miller
William Miller

Level 3 Expert

9098 Answers

Jerry Umali

Level 3 Expert

979 Answers

richie46

Level 3 Expert

12962 Answers

Are you a Scanport Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...