Question about Hotpoint Aquarius WD640 Front Load Washer/Dryer

1 Answer

Display lights The display lights on my machine say test whenever I start a cycle. I have lft the test cycle do its thing and try again and test continues to appear. On the test cycle it dosn't take on water or powder just seens to go around in differnt directions. I have read my manual and can't find a solution. please help

Posted by on

  • Anonymous Dec 14, 2007

    The display lights on my machine say test whenever I start a cycle. I have left the test cycle do its thing and try again and test continues to appear. On the test cycle it dosn't take on water or powder just seems to go around in different directions. I have read my manual and can't find a solution.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 249 Answers

Make sure there water going to machine, remove fill hose to see check inlet filters.good luck eire

Posted on Dec 07, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The error message "door" is displayed and the machine won't start. I can I reset it.


I have Blomberg WM87120 NBL00 Product code 717518110 and had flashing Lock in display. Bought and installed new lock and no change. Display still flashing lock. Used following procedure and every is working now.
Press pause button and hold down while turning off machine.Continue to hold pause button and turn power back on. If numbers come up on display make note of them for future reference. Release pause button and all lights on display will light up. Turn power off again and then turn back on. If machine was in a cycle it should end it and then return to normal operation. .Dont know if new lock made a difference. Try the reset procedure first.

Dec 08, 2012 | Blomberg Washing Machines

1 Answer

Ge adora washing machine beeps when pushing start with door closed


Hit the power button until there is NO display . Unplug and wait a minimum of 30 seconds , plug back in and within 30 seconds hit SIGNAL button then DELAY START button then SIGNAL button again then DELAY START button again. door should lock and display t01 It is now in test mode . There are 14 different test it can run through in this mode , but all we are trying to do is check for error codes now and maybe get you back to normal, So turn the knob one click clockwise and hit the START/PAUSE button and see if any error codes come up. To exit the diagnostic mode - hit signal button then delay start button then signal button then delay start button and you are out of service test mode and back to normal. Post any error codes.

Dec 07, 2012 | GE WSXH208A Front Load Washer

1 Answer

First time it happen I notice that it started before it should with the timer, so started it without timer and it worked. Now its not going though circle again. Changing the program, and trying again,...


1) you must test the timer is stuck with the contacts, you can try to clean it, tight loose wires, test wires open or break. Or doesnot replace complete TIMER. The timer contacts if you see the diagram is determinant control all operation machine of the diswasher. God bless you

God bless you
7_11_2012_8_29_58_pm.gif7_11_2012_8_30_13_pm.gif

Jul 10, 2012 | Hotpoint-Ariston LFT 228A 23 in Builtin...

1 Answer

Test mode


press start once
then press start again now hold on/off and cancel together for a few secs should no say d/off or something should work now

Aug 22, 2009 | Hotpoint Ultima WF865 Front Load Washer

2 Answers

Hotpoint WF645 error message: test


press start once then press again then hold on/off and cancel for a few seconds should now turn test off should be ok now

Jul 15, 2009 | Washing Machines

4 Answers

Hotpoint wf840 displays "test"


Try This - It works for the Washer Dryers so it May work on your Washer.

  1. Press the Start/Cancel button until all the console Led's Illuminate
  2. Press both Start/Cancel and On/Off buttons together until 'd off' appears
  3. Default screen should return and you can select a new programme
Hope this Helps.

Mar 12, 2008 | Hotpoint Ultima WF840 Front Load Washer /...

2 Answers

Test display


hi there let your machine do the compleat test cycle again then when it gets to the end press and hold the start/cancel button and the on/off button at the same time for at least ten seconds.

hope this is of some help

Dec 14, 2007 | Hotpoint Aquarius WD640 Front Load...

Not finding what you are looking for?
Hotpoint Aquarius WD640 Front Load Washer/Dryer Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1211 Answers

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

puggy666

Level 1 Expert

48 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...