Question about Foxconn f845s Motherboard

1 Answer

Display of vga card which is AGP Socket

Hi There,
Do you think my Motherboard is dead?
Foxconn f845s is the moterboard I have since 2003 which uses a Pentium IV 1.7Ghz cpu processor. When I boot the system all the other components respond as the lights on the HardDisk,Floppy,SystemRedLIght go on but the display does not come on(the monitor works fine on my other system) If the AGP part of my display port does not works can I physically bypass it?
The Problem started when the system slowed down after I accidently deleted a Nero Installation and then the Floppy drive went defective so I installed a new one.Then the display went defunct!!!
Thankyou for your valuable time spent to read this appeal
and help me if you can and tell me if its wise to get another f845s motherboard to replace this one or is there a no-way-go-bad motherboard in the market to install???!!! for me.
Yaz

Posted by on

  • Yaz Pat Dec 09, 2007

    HiYa,

    It does help to be intouch with you and I have sent my f845s motherboard for repairs to Banglore, sure will let you know when the repair is done and the cause for the crash (I think its the powerPack which I had got repaired a year or so back).

    Yaz

    09-12-2007

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,601 Answers

It is unlikely that the floppy took out the agp display controller,
I assume that you have no video when the computer startsup also.
But if that is the case you can use a PCI video card.
Are the fans and hard drive running?
When you were in the case replacing the floppy did you make sure that nothing else was disturbed and were wearing an antistatic strap?
I would go over all of the wires inside.
Please let me know how you make out.

Posted on Dec 08, 2007

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can foxconn 661m03 handle ati radeon 4650 agp?


Hello here is the foxconn homepage:

http://www.foxconnsupport.com/Default.aspx?Language=en-us

The graphic card will fit the mainboard, all graphic card with the AGP socket will fit, there is no limit here.

When adding a bigger graphic card, the power supply can be too small for the system.
I would suggest a 400 watt psu or bigger, for a smooth running system.
A more expensive graphic card is always better, depending what you have to use it fore.
More system memory (ram) can also help, if you intend to playing games.

The newest AMD driver can be downloaded here:

http://support.amd.com/us/gpudownload/Pages/index.aspx

By selecting the graphic card model, and your windows system.

Hope this will help you

Mar 19, 2013 | Computers & Internet

1 Answer

Which vga card compatible wit P4M800PRO-M2, Pci or AGP?


Hi. Thanks for your question.

Video card compatible with your motherboard is an AGP 8x.
Hope this helped. For more info about your motherboard please see this link------>http://www.dealtime.com/Elitegroup-ECS-P4M800PRO-M2-2-0-Via-Socket-775-MicroATX-Motherboard-Audio-VGA-AGP-8x-10-100-Ethernet/prices
Thank you for using FixYa.

Dec 17, 2010 | EliteGroup P4M800PRO-M2 (V2.0) Motherboard

1 Answer

Foxconn motherboard n15235 no viedio


Hi,

That motherboard is either a P4M800P7MB-RS2 or a P4M800P7MB-RS2H, even thou it has N15235 stamped on the board. The board
Supports VGA display function (S3 Graphics UniChromeTM Pro IGP)
but, also has an AGP 8X slot. A slot that allows you to install a AGP 8X (AGP 3.0) card. A AGP 8x is the VGA interface specification that enabled enhanced graphics performance with bandwidth speeds up to 2.1 GB/s.

Hope that answers your question.

Mark

Apr 23, 2010 | Foxconn 6627MA-RS2H Motherboard

1 Answer

I bought Foxconn 755A01-6EKRS Motherboard for my HP pc replacement. i install my AGP VsionTek x1300 graphic card and turn it on and nothing show up on screen...then i put the graphic card back to my old HP...


Your new Foxconn motherboard Primary Graphics Adapter settings in set to onboard vga that is why there is no display in your monitor. Do not install yet your agp video card. Use first the onboard vga of the motherboard.
Power up your computer and go to the BIOS settings. Locate in bios about the Primary Graphics Adapter settings and then select AGP. Save changes and the exit. Turn off your computer and now install the agp video card.

Dec 16, 2009 | Foxconn 755A01-6EKRS Motherboard

1 Answer

Vga driver


I found the site to suggested to you.

Foxconn Site
Link

Direct Driver Download
Link >>> VGA Board Driver
Link >>> AGP Driver

Just Click and follow the link

Or you can download it from sis website, coz this motherboard uses the SiS 760GX motherboard chipset drivers, which you can download directly from SiS:

http://www.sis.com/download/



Jun 03, 2009 | Foxconn WinFast K7S741MG Motherboard for...

2 Answers

PC Motherboard Query


Hi there
This Socket 754 board will accept up to 3GB of DDR 400 memory and an 8x AGP video card
Thanks for Using Fixya

Jan 13, 2009 | Foxconn (755A01-6ELRS) (K8S755A6ELRS)...

2 Answers

Cd motherboard broken


Foxconn K7S741M Motherboard


AMD onboard audio drivers for 32bit.
Download On board Audio Drivers

Download On board VGA Drivers

Download AGP Drivers


I hope this resolves your problem
all the best

Jan 05, 2009 | Foxconn WinFast K7S741MG Motherboard for...

1 Answer

ASrock P4i45GV Motherboard


Hi sandesh8, did you know you can increase the memory size of the onboard AGP card above the 64MB? Page 26 in you're manual. If you install another AGP card into the opened AGP slot, please go to this site & only use the recomended AGP cards in the Asrock list. Click on this link: http://www.asrock.com/mb/vga.asp?Model=P4i45GV%20R5.0&s=478&c=VGA
This is one of very few video cards found on the list with 256MB of video memory.
http://www.amazon.com/nVidia-GeForce-FX-5700-5187-6725/dp/B000RPKI28

Good Luck!
Mike

Jun 08, 2008 | Asrock P4I45GV R5 Motherboard

1 Answer

How to disable onboard VGA


I believe if you install an AGP card the onboard VGA is supposed to be automatically disabled. Did you buy an AGP card?

Nov 28, 2007 | Foxconn P4M800P7MA-RS2 Motherboard

1 Answer

Video card troubles


Hi, with my own Foxconn mobo [661FX7MI] I had to run the installation disk that came with the motherboard and reinstall the AGP driver. Then run the AGP card driver [ATI]  disk.

Regards mistyman

Oct 20, 2007 | Foxconn 760GXK8MC-RS Motherboard

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Foxconn Computers & Internet Experts

Alun Cox

Level 3 Expert

2678 Answers

Rommel Balcita

Level 3 Expert

749 Answers

David
David

Level 3 Expert

781 Answers

Are you a Foxconn Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...