Question about Mitsubishi VS-60705 60" Rear Projection Television

1 Answer

Mitsubishi 60" projo tv model vs-60705, blanking bar

Picture is great, BUT, 4" high blanking bar in middle of picture. Bottom half of picture is on top, top half is on bottom. Replaced IC451 (vertical) and 8 electrolytics in vertical circuit. No change.
Then, thinking of blanking problem, I went to signal board and found electrolyte spewed out on board from cap. I cleaned up board and replace cap. No change.
I have seen problems before in Mitsubishi from these cap eruptions.
I don't have diagram. I would replace signal board if I could find number and could get parts for Mitsubishi.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,153 Answers

Also info at www.ctechnicians.com

Posted on Dec 06, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My tv mitsubishi vs-60705 looks great when i first turn it on after it warms up picture starts to shake and gets worse the longer its on. what is overheating to cause this ?


Sounds like you have a swollen cap in your horizontal hold circuit. Look at your board closely, and I am sure you will find one that is bulging on the top. Just replace with the same value.

May 16, 2011 | Mitsubishi VS-60705 60" Rear Projection...

1 Answer

Vertical blanking


CHECK C2C52 10 UFD @ 50 V OFF THE BASE OF Q2C51 ON THE SIGNAL PCB. 2. CHECK C2P05 100 UFD 16 V OFF PIN 3 OF IC2P01 AND IC2P01 PART # 270P466020 (9-VOLT REGULATOR). BOTH ARE ON THE SIGNAL PCB.

Dec 06, 2007 | Mitsubishi VS-60705 60" Rear Projection...

1 Answer

Horizontal lines in the picture.


Give it time to warm up like another 10 to 15 mins i find put a tv guide channel on the screen stays pretty much the same picture, then leave the TV on" i use a 4 hour rule if i dont view in 4 hours or more i will close tv power

Oct 07, 2009 | Mitsubishi VS-60705 60" Rear Projection...

1 Answer

Vs-60705


My Mitsubishi Model VS-60705 did the same thing a couple of years ago...A TV repair facility replaced the Video card. Any repair facility that works on rear-projection TV's should be able to repair your set. I bought the set on Jan 1, 2000. Coming up on 9 years and the set works like new.

Jul 30, 2008 | Mitsubishi VS-60705 60" Rear Projection...

1 Answer

Tv problemsMitsubishi VS-60705 60 in....


My Mitsubishi Model VS-60705 did the same thing a couple of years ago...A TV repair facility replaced the Video card. Any repair facility facility that works on rear-projection TV's should be able to repair your set.

Jul 10, 2008 | Mitsubishi VS-60705 60" Rear Projection...

2 Answers

Mitsubishi VS-60705


I have a Mitsubishi VS-60705 and the picture flutters vertically and horizontally i need to be fixed

Dec 04, 2007 | Mitsubishi VS-60705 60" Rear Projection...

1 Answer

I have a Mitsubishi VS-60.. With a Picture


Vertical IC outputs , vertical Capacitors are most like the culprit on your deflection panel. good luck

Aug 16, 2007 | Mitsubishi VS-50501 50" Rear Projection...

2 Answers

Mitsubishi VS-60705 - picture flutters vertically and horizontally


This sounds like one of the 9 volt regulators on the small signal board is going bad, supplying less than 8 volts. I have seen this is several of those sets. The IC needs to be replaced and if you do not have experience in servicing projection TV's then I suggest letting a qualified tech handle it for you.

Jul 09, 2007 | Mitsubishi VS-60705 60" Rear Projection...

1 Answer

Horrizontal fluttering when warmed up.


1. HORIZONTAL PULLING AND TEARING, MAY ALSO HAVE VERTICAL ROLLING OR VERTICAL BLANKING BAR LOCKING IN THE MIDDLE OF THE PICTURE. CHECK C2C52 10 UFD @ 50 V OFF THE BASE OF Q2C51 ON THE SIGNAL PCB. 2. CHECK C2P05 100 UFD 16 V OFF PIN 3 OF IC2P01 (9-VOLT REGULATOR) ON THE SIGNAL PCB

Oct 18, 2006 | Mitsubishi VS-60705 60" Rear Projection...

Not finding what you are looking for?
Mitsubishi VS-60705 60" Rear Projection Television Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1213 Answers

The Knight
The Knight

Level 3 Expert

75157 Answers

Jaime Hernandez

Level 3 Expert

2334 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...