Question about Kitchen Ranges

2 Answers

Kenmore Gas Range - burners won't ignite

I have a Kenmore gas range, model number 362.7556191. I was cleaning the top of the stove this morning and when I turned on the knobs for the burners, they wouldn't ignite. All I get is a clicking noise. The oven and broiler work fine.

Posted by on

  • 2 more comments 
  • Anonymous Dec 29, 2007

    I have had this problem with a different brand gas igniting stove top. Usually I will make sure it is clean in/around the spark unit (usually located at the top near the slotted holes. Also, I ensure that the top plate is seated correctly on top of the slotted gas exit area. Sometimes I use a match to start the unit and it will work the next time I use the spark igniter. Good luck ... Please try any/all before hiring or calling in any service repair person... This has worked for me for years. Tommy O

  • Anonymous Mar 12, 2014

    My Kenmore gas range is reading F90. The oven does not work and the stove top does not work. What is F90?

  • Anonymous Mar 14, 2014

    kenmore gas range 74032

  • Anonymous Mar 19, 2014

    Burners and broiler ignite but oven does not

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 362 Answers

Its possible your gas regulator is bad or the gas line to the ignitor is stopped up look at the line and see if some type of food has blocked the outlet

Posted on Dec 08, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Igniter failure after cleaning burners

Posted on Oct 16, 2009

6 Suggested Answers

jbjaxiis
  • 95 Answers

SOURCE: Amana oven and broiler won't fire

Check your stove breakers first. Click them off, leave them off for a minute and put the breaker back on. It sounds like you are having a power supply problem. Make sure to check your potlet and power chord as well.

Posted on Jul 08, 2008

  • 4 Answers

SOURCE: AMANA GAS RANGE ARG7302

sounds like the thermostat

Posted on Dec 11, 2008

  • 1 Answer

SOURCE: Kitchenaid Gas convection range lower burner will

whirlpool oven wont turn on top burner work.
model #SF315PPQ2

Posted on Sep 05, 2009

heatman101
  • 43501 Answers

SOURCE: Maytag Gas Range broiler burner not working

Hi,
The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating
http://www.fixya.com/support/r3663023-oven_not_working_or_oven_not_heating

Oven Problems Replacing the Igniter http://www.fixya.com/support/r4572625-oven_problems_replacing_igniter

heatman101

Posted on May 21, 2010

heatman101
  • 43501 Answers

SOURCE: Gas oven on Kenmore range model 362-75191890 went

Hi,

The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating

Oven Problems Replacing the Igniter


heatman101

Posted on Nov 27, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Igniter glows but why doesn't burner light?


Igniter could still be faulty(not hot enough) or burner control valve
faulty. press the helpful button and check link videos below
Gas Stove Top Burners Not Lighting Not Working

Gas Stove Ignitor and Burner Not Lighting

Daddy Chores Gas range won ignite How to fix it


Jan 22, 2016 | Kitchen Ranges

1 Answer

Kenmore gas range 790, not getting gas to the stove top, oven works, all 4 igniters fire when any knob is used. Is this a safety shutoff and how do I fix it?


Burner Spark Electrode Replacement - Kenmore Gas ...

? 2:23
www.youtube.com/watch?v=U0VcfMJPaiY

Nov 12, 2010 - Uploaded by RepairClinic.com
+Tony Eatinsky If the electrode is not damaged than the spark module ... I have a kenmore gas stove ( 362.7555190) that won't ignite unless I use a match. ... I have a Kenmore Elite 5 burnergas range top, it auto light continually sparks? .... You most likely will need to cut or grind off the screws and get new ...

kenmore model 790 gas range. the gas stove top burners ...

www.shopyourway.com > Manage My Life > Questions
kenmore model 790 gas range. the gas stove top burners stopped sparking. ... NOTE: I do not recommend measuring voltage unless you have experience and feel ... if the spark module is getting 120 volts when the burner knob is turned to the ...

Oct 19, 2015 | Kenmore Kitchen Ranges

1 Answer

Stove burners don't ignite ,the regulator isn't letting the gas go to the range kenmore gas stove model 665 75022101


First, check to make sure gas is actually getting to the range and hasn't been stopped by a clog or simply shut off accidentally. Next, make sure the120v AC is present. If you verify that gas *is* reaching the range and there is 120 volts getting to the range, then the main gas valve is next in line(where the gas line connects). The part numbers for the main valves in the range are:
8523378, gas shut-off
8054079, gas valve
I hope this helps you!

Sep 15, 2015 | Kenmore Kitchen Ranges

1 Answer

Can the cooktop surface of my Kenmore gas range model 790.72903011 be removed


Most stove tops are removable for that very purpose.... after you remove the burners and the grills above the burners.... look for an edge and inch or inch and a half below the top... get something strong like a large screwdriver and place cloth over the tip to prevent scratching the stove top. there are VERY STRONG CLIPS holding the stove top to the stove, pry upward until the clips release. then slowly remove the spark igniter (TAKE A PICTURE WITH YOUR CELL TO REMEMBER HOW PUT BACK TOGETHER)

Jul 30, 2014 | Kenmore 79012 / 79014 / 79019 Gas Kitchen...

1 Answer

The electric panel on my smooth top stove just went out with a popping sound rendering the oven unusable but the stove top burners are working.............what could have happened and is it worth it to get...


Electric gas igniters sometimes get stuck in one position causing a clicking sound. The clicking sound that you hear is the electric arc that is pulsing from the igniter conductor (wire) to ground (the gas burner). It receives power from the electrical outlet that the stove is plugged into.
Residue from food and sometimes cleaning products may be preventing the igniter from producing a spark (Arc) to the base of the burner. This is a common problem that occurs when the stove has been cleaned or food is allowed to build up. Make sure that the igniter and the burner base are clean and dry. This will help with proper operation. Oven cleaner and a small tooth brush may be used to accomplish this. Another problem with ignition may occur if you have too little (touching) or too much space between the igniter and the base of the burner; it will prevent the burner from igniting. You should only have a little more space than the thickness of a nickel between the burner base and the igniter. A good "blue" arc from the igniter to the burner base is optimal. If this doesn’t work, you may need to replace the electric igniter module. Good luck.

Jul 21, 2010 | Kenmore 95423 Stainless Steel Electric...

1 Answer

Stove top ignitors do not ignite but oven does.


Electric gas igniters sometimes get stuck in one position causing a clicking sound. The clicking sound that you hear is the electric arc that is pulsing from the igniter conductor (wire) to ground (the gas burner). It receives power from the electrical outlet that the stove is plugged into.
Residue from food and sometimes cleaning products may be preventing the igniter from producing a spark (Arc) to the base of the burner. This is a common problem that occurs when the stove has been cleaned or food is allowed to build up. Make sure that the igniter and the burner base are clean and dry. This will help with proper operation. Oven cleaner and a small tooth brush may be used to accomplish this. Another problem with ignition may occur if you have too little (touching) or too much space between the igniter and the base of the burner; it will prevent the burner from igniting. You should only have a little more space than the thickness of a nickel between the burner base and the igniter. A good “blue” arc from the igniter to the burner base is optimal. If this doesn’t work, you may need to replace the electric igniter module. Good luck.

Mar 20, 2010 | Whirlpool 30" Self-Cleaning Freestanding...

3 Answers

Kenmore Range/oven Burners won't lite


Ours did the same, I unplugged the stove for 1 minute and afterwards the burners worked fine.

May 19, 2009 | Kenmore 75844 / 75849 Gas Kitchen Range

1 Answer

Kenmore gas range


hi Clogged burners are a very common problem with gas ranges because foods spilled on the burners block the gas ports and prevent ignition. On some gas ranges you can remove the top ring of the burner to expose the ports. Here's how to clean a burner:

Step 1: Turn off the power supply, both gas and electric, to the range. Then remove the burner.

Step 2: Soak the burner in a solution of mild household detergent and water. Clean it with a soft cloth.

Step 3: Clear the gas ports with a pin or needle, rinse the burner, and let it dry. Caution: Do not use a toothpick or matchstick to clean the gas ports. If the tip of the wood gets stuck in the burner ports, it could cause a serious blockage.

Step 4: When the burner is completely dry, replace it, and turn on the power and the gas supply.

Nov 06, 2008 | Kenmore 75022 / 75024 / 75029 Gas Kitchen...

2 Answers

Kenmore Elite Gas Stove


Will have to ask some basic questions first.  How old is the stove?  What is the entire model # from the sticker on the unit?  Is this LP or natural gas?  Also, make sure that the orifices in the center of the burners are clean (can use a safety pin or paper clip to poke them a few times to clean).  Make sure that the black caps are on top of the burners and seated properly or they will not lite.  Let me know what you find.

Oct 16, 2007 | Kenmore 79383 Dual Fuel (Electric and Gas)...

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

3,205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8209 Answers

yadayada
yadayada

Level 3 Expert

71856 Answers

paulcarew

Level 3 Expert

2404 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...