Question about Hobart 24 in. LXIH-3 Built-in Dishwasher

4 Answers

LX30H Hobart torsion bar adjustment

I have a hobart LX30H when you open the door if you dont hang on it just slams right down. Is there a way to adjust the torsion bar on this machine, I called Hobart and was told no that i needed to buy a torsion bar ,torsion bar assymbly,and 2 o ring any help would be nice thanks

Posted by on

  • broken06 Dec 07, 2007

    i went to this site because i would like to fix the problem if there is no way to adjust the torsion bar thats ok ill buy the new one i just wanted to know before spending the money

  • Hoang Do
    Hoang Do Jan 05, 2018

    If the doors are dropping its because the middle hex bar broke. There is no adjustment to that. Just a replacement. Getting just the central hex bar is a worthwhile endevor but usually the outer sleave is probably cracked and deformed at the block as well.

×

Ad

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Im a service tech for hobart,there are no adjustments,the torsion bar is broken.the parts arent expensive but installing them are tricky.

Posted on Dec 16, 2007

Ad

Bubbaloo

Posted on Aug 09, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Wind them up

Posted on Jan 03, 2008

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 1 Answer

Replace the torsion bar if the outside sleeve isn't twisted and cracked. Otherwise replace the whole thing.
LX30H Hobart torsion bar adjustment - 1_5_2018_10_46_41_pm.jpg

Posted on Jan 05, 2018

  • Hoang Do
    Hoang Do Jan 05, 2018

    Replace the torsion bar if the outside sleeve isn't twisted and cracked. Otherwise replace the whole thing.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hobart lx30h leaking from bottom


This is a testing for the post on this web site, not a solution.

Mar 27, 2014 | Hobart Lx30h Commercial Dishwasher

1 Answer

LX30H THROWS A CODE EO after running awhile. I hit the high reset button under the flaps on the front for both the boost and reg elements . It will work for a couple cycles and then does the same thing....


Machine won't fill or won't fill high enough. site water pressure meets minimum flow pressures. (LX18, LX30 display shows working.
"E0," "E2," "E3," or "E4". LX40 display shows "DR1 PRBLM," "FILL1 PRBLM," FILL2 PRBLM," or "FILL3 PRBLM". Machine will not run.)

1. Low water pressure - check for clogged hose strainer; check that

2. Make sure probes are clean

3. No water pressure - main water supply valves may not be

4. Drain valve open - turn machine OFF to drain machine, then
ON. Repeat twice (this assists in clearing any drain valve
obstructions). Wait for machine to reach READY mode and
press WASH. Slowly open door several seconds later and note
water level. Close door; 30 seconds later, open door slowly and
check that water level is the same as it was. If not, repeat the
OFF-ON procedure. If problem persists, call your local Hobart
Service Office.

5. Delime machine.

https://my.hobartcorp.com/resourcecenter/ProductDocumentation/F18615%20Rev%20I.PDF

If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

Dec 10, 2013 | Hobart Lx30h Commercial Dishwasher

1 Answer

Hobart lx30h rinse additive is running all the


The main cause is the "anti flood" device at the bottom of the washer that detects a water leak "hose leak" etc. This device made up of a polystireen float and micro switch is a safety device and when activated puts the washer in pump out mode only. You need to look at the base of the washer and see if water leak has caused this. Rectify the cause "normaly hose or clamp" and this should clear the

Mar 21, 2010 | Hobart 29 in. AM15-1 Free-Standing...

1 Answer

Hobart dishwasher model LX30H displays -5 on


by the way you're describing the problem, i would have to say there is something wrong with your control board. part#473173 can be bought @ any hobart office in your area. dont forget to vote

Feb 07, 2010 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Lx30h P2 ERROR CODE? WON'T DRAIN COMPLETELY - HELP


the p2 err. is on open or shorted rinse thermistor which is located on the back of the mach next to the vac. brkr. as for draining ck the drain valve for debris, and the end of the drain hose where it connects to the building drain

Dec 25, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Lx30h hobart dw. booster will not turn on. element good,hi-limit is good, changed temp probe, still no power to contactor


The booster heat control circuit is controlled by the relay board. Visually check for loose or burnt relay contacts...
You will see the booster LED light when it calls for heat. Some newer machines have a second high limit on the right hand side of the booster tank.
It may be your control board is configured for low temp with no booster. When you power up, the display should say LX30H. If not
Pull open the upper drawer, place a magnet over the door interlock switch.

CAUTION, 220 volt power is present. be carefull what you touch.

on control board, short J5-1 and J5-2, then power up. You are in factory setup. press select on the control board to see each option on the front panel., press up arrow on control board to step up through options for each step. when done, press the off button on front panel. remove short and start up normally. With the magnet in place, AND THE DOOR CLOSED, run the machine and observe the relay board status lights.
If you want to adjust the temp set points, with the machine off, press and hold the hidden key behind the front panel logo, and press select on the control board.. Or on power up, hold the wask key..Same to adjust options as above. Press off to exit.

Jul 04, 2009 | Hobart 24 in. LXIC-5 Built-in Dishwasher

Not finding what you are looking for?
Hobart 24 in. LXIH-3 Built-in Dishwasher Logo

997 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Marvin
Marvin

Level 3 Expert

82322 Answers

Garth Jackson

Level 2 Expert

93 Answers

handygirl911
handygirl911

Level 2 Expert

65 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...