Question about Flat Panel Televisions

2 Answers

I want to reset my TV

I have a Technika LCD 26-207 but it is stuck in analogue mode, I want to completely reset the TV so that I can restart it in Digital mode. When I am on the DTV setting the remote will not bring the menu up so i am unable to tune the TV in Digital. Also when I put the TV on standby via the remote the blue light on the TV keeps flashing and it will not switch on from the remote, I have to turn the TV off and on again.

Any help would be most appreciated......

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: I want to reset my TV

But iv tryed that and the blue light gos out then straight back on again my technika lcd37 907 y as everyone else on here the blue light flashing my stays on

Posted on May 24, 2014

Re: I want to reset my TV

Well when the blue light is on and ur tv is on standby, just use the channel changing button, simple!

Posted on Apr 10, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My Technika 15.6-600 lcd tv is behaiving abnormally, is doing on and off modes, what should I do?

Fault to its main board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. . In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Dec 01, 2015 | Flat Panel Televisions

1 Answer

How do I get my Sky channel back on analogue after re-tuning freeview

Go in to analogue tuning. Tune just the analogue side of the TV.

Sep 05, 2014 | Flat Panel Televisions

1 Answer

Technika tv help line

check the settings in the tv setup menu, the AV ports can usually be configured for analogue or digital,

Dec 07, 2013 | Flat Panel Televisions

1 Answer

I brought this remote and it doesnt have a code for my technika tv do you have an answer?

For Technika, pls try following code:
1171 1231 1261 0012 0432
or alternately, please try the magic search code as follows: 1. Turn On your device (LCD TV) 2. Press device mode (TV) from your URC (universal remote control) 3. Hold (P+ or Ch+) and (Vol -) on URC at the same time for two seconds until indicator lights up 4. Enter "magic search" code - press device code (TV), then press (P+ or Ch+) and (Vol -) on URC, and enter device (TV) magic code # 0001 5. Press device mode (TV), same or repeat process # 2 6. Hold (P+ or Ch+) and (Vol -) on URC at the same time for two seconds until indicator lights up and your URC is ready to start searching. 7. Aim the URC at your device (LCD TV), press the POWER KEY repeatedly, slowly and patiently until your device (LCD TV) switched off. 8. Once your device has been switched off, immediately press (P+ or Ch+) and (Vol -) to lock in the code and the indicator should go out. 9. If fail, please try complete process from 1 till end.
Hope it works, since it works for me.

Jul 02, 2011 | Flat Panel Televisions

1 Answer

We are stuck in analogue mode and cannot tune tv into dtv how do we reset its a technika 22in tv

Please email with your full model number to confirm if the product is one of ours so we may assist you further if it is or call tesco helpline on 0845 456 67 67

Feb 02, 2011 | Flat Panel Televisions

3 Answers

How do I reset my tv to factory settings. samsung 32 inch LA32R81WDx/xSA

On a different Samsung TV, there is a Picture Reset in the Picture Menu on the OSD. (It's at the bottom of the list.) Similarly the sound reset is in the Sound menu. There is no global reset. (If your Samsung TV's OSD menus are different try under the Support menu.)

I hope this helps.

Cindy Wells

Aug 05, 2010 | Samsung LE32R73BD 32 in. HD-Ready LCD...

2 Answers

Technika LCD15DVDiD-108 no picture - sound ok

did anyone solve this please? i have the same problem and cant afford expensive repairs x

May 01, 2010 | Flat Panel Televisions

1 Answer

How can I get an analogue signal on my LG3000 32in LCD tv? Digital input is fantastic, but no idea how to obtain analogue. Input is connected to a community arial and other residents get analogue with no...

According to the manual I looked at, this TV has only one antenna input. This means that analog is available if you let the TV do a full autoprogram of memory. It might take it several minutes to complete, but once its done you should have analog and digital if available. If you were looking for analog channel 5 then you would just enter 5-0 but digital channel 5 would be 5-1.

Nov 12, 2009 | LG 32LG30 32 in. LCD HDTV

3 Answers

Ive just been given a Technika television LCD19DVDID 308 and I can't find out how to watch analogue channels,can anyone help me please?

have fitted a new aerial as tv was connected to sky and now cant get any freeview channels keeps saying no signal what am i doing wrong

Mar 16, 2009 | Sampo PME-50X7 50 in. HD-Ready Plasma...

2 Answers

Samsung lcd faults

Found this on FixYa and it worked:

I had a similar problem and the way to solve this is to reset the set from the remote. Set TV to standby and press Info, menu, mute then power. The set should turn on with the service menu available scroll down until you select reset press right hand arrow next to enter and then enter. TV will turn off. When switched on it goes into Plug and Play mode to reset the analogue and digital tuner. Allow a full reset then you should be ok.

Mar 10, 2008 | Samsung LE26R74BDX 26 in. HD-Ready LCD...

Not finding what you are looking for?
Flat Panel Televisions Logo

Related Topics:

2,191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Flat Panel Televisions Experts

The Knight
The Knight

Level 3 Expert

66552 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides