Question about Sony Grand WEGA KDF-60XS955 60" Rear Projection HDTV

2 Answers

No power red ligth blinking 6 times

Standby ligth blinking 6 times pause and blink 6 times and so on , no picture and no sound

Posted by on

  • 2 more comments 
  • pillo85 Dec 09, 2007

    thanks a lot, my tv is working like a champ again.

  • Anonymous Dec 29, 2007

    Hi,

    I have the same problem my sdf60xs955 red light blinking 6 times in pattern. I already opened the back of my tv. The problem is I don't know how to locate the thermal fuse. (I think there're more than one fan on the back of my tv) Please help. Thank you, Paul

  • Anonymous Jun 25, 2008

    I replaced lamp tv worked 30 min or so. then sound & picture went out red light brinking ? what next

  • brandonatgmg Apr 03, 2009

    my tv shut off and went into standby mode and now the red light blinks 10 times

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 137 Answers

OK, Here is another easy Fix, The problem is your Thermal Fuse is no Good (open) This can be found near the lamp housing. To fix this, you need to take the back off. Remove the Fan, look into the lamp housing. There is a plug with a small black tip mounted near the lamp. This need to be changed. Its just unplugging one cable and put the new on in. Part Number 1-910-023-93, average cost $4.80

Best regards
CircuitCity

Posted on Dec 06, 2007

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

The problem is the thermal fuse. You need to have service bulletin to fix it. I have seen other people have the same issue and it was fixed by getting the SB at agoraquest. It's a step by step guide on replacing the thermal fuse. The member that has the service bulletins is Jehill. He has helped several people with this issue

http://www.agoraquest.com/viewtopic.php?topic=24322&forum=34&start=0&select_page_number=1

It takes about 2 hours but saves over $400 in service repair bills.

Here are some of the people that were helped by this

-----------------------------------------
J/K :-p ......worked like a charm :-) Took me about 2 hours and almost half of that was to go and get a 20" #2 philips screwdriver. A 12" would have worked, but they did not have it. Other than than that, no problems. I paid $220 for the TV, $28 for (2) Thermal Fuses, and $11 for a screwdriver. Now I have a decent 2nd TV :-) Not as good as my KD-34XBR960, but not much is :

Happy

-----------------------------------------------------------------------------------------------


I just got done replacing the thermal fuse as per your SB and all is well again! I, and most importantly the wife, just want to take the time to thank you so much for your help. With your instructions and this site, we have just saved ourselves alot of $$ not just for this time but also if it were to happen again in the future. I am truley grateful for finding this site and just want to say you are THE MAN!!!

pratt31

------------------------------------------------
1 10" screwdriver $12.00
1 Sony Thermal Fuse + shipping $ 8.00
1 membership to agoraquest.com $12.00
Fixing the thermal fuse myself on a TV that was discarded at the curbside

PRICELESS

Posted on Apr 14, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My tv don't ligth but isow the red ligth at the corner which ligthing and ligthing again.What can i do?


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
https://homenol.blogspot.com/
https://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty./

Mar 23, 2018 | Televison & Video

1 Answer

Standby light blinks 6 times pause and blinks again


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/

Dec 05, 2014 | Sony KDL-52XBR9 52 in. LCD HDTV

1 Answer

WHAT IS BLINCKING LIGTHS ON TV MEANS


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty.

Nov 24, 2014 | Televison & Video

1 Answer

MY SONY TV MODEL # KF42-WE610 IS SOUND IS COMING ON BUT NO PICTURE


If you turn it on and the, Power/Standby green light blinks slow 6 times; then it becomes a red fast blink 6 times, pause, then continues to blink red fast 6 times, again and again. this means when it's blinking 6 times is indication of electrical circuitry malfunction. The Television will need service.

Sep 30, 2014 | Sony Televison & Video

1 Answer

SONY KP-61HS20 DOESN'T COME ON JUST BLINK 6 TIMES PAUSE AND 6 TIMES AGAIN


Sis blinks of standby light denotes No Horizontal (H STOP), no raster, goes to the blinking self-diagnosis function immediately. If you wish to get more details about blinking codes to Sony PTV, check this link.

Mar 03, 2013 | Sony KP-57HW40 57" Rear Projection...

1 Answer

Standby ligth blinking 6 times pause and blink 6 times and so on , no picture and no sound


Six blinks - No Horizontal (H STOP), no raster, goes to the blinking self-diagnosis function immediately. Check C515 & 516 and the jungle IC, IC206

Apr 29, 2012 | Sony Televison & Video

1 Answer

Sony KV-34xbr800 standby light flahes all the


Hi,
Flashing standby light is an error code that is specific, there would be pause of 3 seconds in flashing, so count pause to pause and let me know that how many times red standby light is blinking to diagnose problem.
Thanks.

Jan 11, 2010 | Sony Televison & Video

1 Answer

Sony Trinitron Wega Standby blinks & the TV won't turn on


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electro-medical.blogspot.com/
http://homenol.blogspot.com/
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Apr 12, 2017 | Sony FD Trinitron WEGA KV-32FS120 32" TV

Not finding what you are looking for?
Sony Grand WEGA KDF-60XS955 60" Rear Projection HDTV Logo

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75178 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1689 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...