Question about Graphics Cards

1 Answer

Psp player If I put the power button to the hold position the light comes on , however if I flick the power switch to bring the unit on there is no action.I presume that the battery is making good connection. Is there a reset configuration on these units or might the problem be more serious Thanks Ivan hulbert

Posted by on

1 Answer

Re: psp player

Hey Ivan,

Take a look at the switch itself, or have someone examine the switch contacts. You may get a signal on one posotion, then trip as it moves onto full on.

Good luck

Posted on Feb 18, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How to reprogram my tablet

if you mean factory default this is it :
1. shutdown the tablet
2. hold volume up button and press the power button
3. when manufacturer logo come leave the power button but keep the volume up button to get to recovery mode
4. in recovery mode use volume up/down button to navigate and the power button to select
5. choose WIPE DATA / FACTORY RESET than select YES .... wait a moment then select WIPE CACHE PARTITION
6. finale step select REBOOT
keep in your mind that all data will be erased

Dec 24, 2014 | myefox EKEN m009S - 7 Inch android 2.2...

1 Answer

Wont boot up

try this..... turn unit off
unplug power
push on button to drain power from capacators
restore power and see if it boots
if not there is softwsre problem

Mar 29, 2014 | Trio 8GB HD 4.3 Touchscreen MP3/Video...

1 Answer

Screen not showing anything when i try to boot up my new pc but the lights and fans work

New PC? Still under warranty correct?

One thing that may have occurred, is in shipping/bringing it home, the Ram Memory module/s may have been bumped loose. (Ram Memory 'stick/s')
Even if they do not look to be loose, the best method is to remove it/them, and reinstall. This way you are assured. (Computer unplugged from power, Anti-Static Precautions observed)

This is usually allowable under a warranty for a Desktop PC.

Past this point it is still under warranty, and should be returned. May be a Power Supply that is bad, or further issues.
Why should you pay for repair parts/labor, when it is supposed to work from the start?

THAT'S what you paid for.

[ 1) IF, all of the LED lights were on at once, they would use less than 1 Watt of power.

(Most of the time all of the LED lights are Not on at once)

2) EACH fan uses 2 to 3 Watts of power.

3) A typical Processor uses 51 to 125 Watts. Just depends on what Processor it is.

With a Power Supply that has a weak voltage power rail, there won't be enough power to turn the Processor on.

No Processor operating, no computer.

{ There are three voltage power rails in an SMPS. (Switched-Mode Power Supply. The type of power supply used in your computer,

A) 3.3 Volt power rail
B) 5 Volt power rail
C) 12 Volt power rail.

You press the Power On button. This in turn presses against a Momentary Contact Switch, the Power On switch.

Doing so, closes a circuit that activates the Soft Power On feature, of the Power Supply.
The Power Supply turns on. The first chipset to receive power is the BIOS chipset. Basic Input/Output System.

BIOS looks to see what devices are installed, does a Ram Memory count, turns the Processor on, and then hands the computer over to the Operating System.

Windows XP, and Windows 7 are 2 examples of an O/S}

IF, you have installed a new graphics card, post back in a Comment.
Also post the manufacturer name of the computer, and it's model number. (Back of desktop computer tower next to the Windows product key, or up on the side of the tower, or behind a hinged door in the front )

If you have any additional questions post in a Comment.


May 25, 2012 | Graphics Cards

2 Answers

ASUS LGA775 mother board

1.Power down your PC.
2.Locate a rocker-style switch at the back of your PC (if applicable), and switch it from the on position (I) to the off position (O).
3.Find the 3-pin jumper near the power supply, typically labeled "clear cmos" or "reset bios".
4.Remove the jumper from the default position (typically connecting the 1st and 2nd pins).
5.Replace the jumper to connect the 2nd and 3rd pins.
6.Push the power button on the front of your PC once.
7.Wait a minute.
8.Return the jumper to its default position, connecting the 1st and 2nd pins.
9.Move the rocker-style switch at the back of your PC (if applicable), to the on (I) position.
10.Power on your PC with its front power button.
If it doesn't work go to alternate options

Alternate Method
1.Locate a rocker-style switch at the back of your PC (if applicable), and switch it from the on position (I) to the off position (O).
2.Remove the CMOS battery. This should be a regular 3V, round, flat watch battery.
3.Wait at least 5 minutes.
4.Reinsert the CMOS battery.
5.Move the rocker-style switch at the back of your PC (if applicable), to the on (I) position.
6.Power on your PC with its front power button.

Alternate Method
1.Turn on your computer and press the key on your keyboard to enter the BIOS. This is typically the Del (delete) key. Pre-built systems from major manufacturers may use a function key such as F1, F2, or F10.
2.Go to the last tab or page of your BIOS.
3.Select an option similar to "restore factory settings".
4.Save your changes and confirm your selection if necessary. This will often be combined with the process of exiting a BIOS. Some BIOS types may have this as a separate option such as "F10: Save Changes".

Nov 21, 2009 | Graphics Cards

1 Answer

I pull out my card for cleaning the system and when i put it back there is no picture on my screen.I try everuthing bit she can`t show any picture like she`a dead...Can u help me please !!!

Hello there:
What you can try to do is first unplug the unit and remove the power cord from the computer.
Now open the case and find the cord that goes from the power supply to the motherboard and disconnect and leave sit for 5 minutes
now press in the power button on the computer and hold in for 10 seconds and release also if there is a reset button press and hold in for 15 seconds this will release any esd that accumulates in the system thus locking up the system now plug in the power supply back into the motherboard and reconnect the power cord and plug in the computer as you normally would and start up the computer now it should work if it still dosn't you might have damaged the card when you removed it.
all it takes is a little static electricity to fry components on these cards
that is why they always recommend using a grounding strap that hooks up to your wrist to ground out the computer case before working on any part of the iinside of the computer ok?
I hope that this has been very helpfull for you
Best regards michael

Nov 05, 2009 | Gigabyte GV-RX26P512H RADEON HD 2600Pro...

1 Answer

The sreen on my HP note book wont turn on. the lights work and i hear the gears running but the sreen stays off. ni indication at all. i was one it in the morning and when i turned it on latter, nothing...

Ok what is the model number of your HP? Pavilion? Get back to me with model number in the meantime, unplug a/c adapter and then remove battery...then hold in power button for 30 seconds and then plug in the a;/c adapter with no battery in it yet. Turn it on and see if that brings it back..if not get me you model for HP

Oct 10, 2009 | HP Graphics Cards

1 Answer

All LEDs are in constant switched on state(BLUE)

When you plug in the source device and the output device, all of the LEDs light blue, letting you know that the device is ready to capture. When you are ready to capture, simply press the play button on your source device, the Rec button on the Video Transfer, and the LEDs light red, both on the source side and the output side, letting you know that a recording is in process. To stop recording, press and hold the record button and when the lights turn blue, recording has stopped.

this is the source:

Jul 25, 2009 | Pinnacle Video Transfer

1 Answer

How to rebot dell laptop

Usually three ways.

Start-turnoff computer-reboot

Three finger salute aka hold down CTRL and ALT and then press the Delete key. That will either bring up task manager where you can select reboot or it will just reboot if you press it again (depends on os version)

Hold down the power button.

Depending on your model there may also be a reboot button that you can poke. It is usualy hidden on the bottom somewhere.

Jul 09, 2009 | Dell Inspiron 8600 / Latitude D800 /...

1 Answer

When I turn on my pc all i get are the led lights on my tower...

if you have the manual see the led instructions to what or where your going to insert the led wires from the case to the motherboard led slots. maybe you put it on the wrong slot. hope that helps!


Aug 14, 2008 | Graphics Cards

1 Answer

Dell monitor power down mode with Geforce GFX card install

I think maybe some how the main graphics for your pc has possibly switched to onboard. Try getting into bios F2 or DEl on boot up and highlight Advanced ChipsetFeatures and press Enter. In here make sure your AGP card is set as the Primary graphics controller. When done press ESC and 'Y' to save settings, then re-boot pc. Hope this gets you running again.

Nov 10, 2006 | Dell (M1325) (64 MB) Graphic Card

Not finding what you are looking for?
Graphics Cards Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Graphics Cards Experts


Level 3 Expert

94113 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

phoenix chi
phoenix chi

Level 2 Expert

389 Answers

Are you a Graphics Card Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides