Question about Brother IntelliFAX 775 Plain Paper Thermal transfer Fax

1 Answer

Answermachine I have a intellifax 1920cn and have lost my guide I do not remember how to delete the messages I have pressed erase and the messages stay it is very frustrating listening to all the same messages again and again Help please

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • Brother Master
  • 1,346 Answers
Re: answermachine

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How do I delete a recording on my JNC Digital Recorder?

I'm not sure about that particular model, but usually you can press ERASE as the message is playing.
On some other models you have to press ERASE at the end of the message you wish to erase.

In either case, right after you press ERASE it will ask ERASE? (or FILE ERASE? ) then you press ERASE again.

Just make sure to experiment a bit so you don't erase a wrong and important recording by mistake.
I don't believe it can be recovered.

May 25, 2011 | Fax Machines

1 Answer

I have a brother IntelliFAX 1270e Plain Paper Fax Phone & Copier machine. It keeps saying Out of Memory/Erase Message. I don't know how to do this please help!!

Just unplug the power cord for a few seconds, then plug in again. this will erase all fax memory except speed dial and phone book numbers,or you have here manual to download ( look at the end of the user manual,option how to retrieve a fax. there you have listed how to delete faxes in memory).

Hope it helps

Feb 11, 2011 | Brother IntelliFAX 1270E Plain Paper Fax

1 Answer

How do I delete speed dial numbers on the Intellifax 2820?

Changing One Touch (For FAX Models Only) and Speed Dial Numbers
If you try to store a One Touch (FAX models only) or Speed Dial number in a
location where a number is already stored, the LCD shows the current name stored there, and then prompts you to either:
1 Press 1 to change the stored number-OR- press 2 to exit without making a change.
2 Enter a new number, and then press Menu/Set.
• If you want to erase the whole number, press Stop/Exit when the cursor
is to the left of the digits. The letters above and to the right of the cursor will be deleted.
• If you want to change a digit, use or to position the cursor under the digit you want to change, and then type over it.
3 Follow the directions beginning at Step 4 in Storing One Touch Numbers
(For FAX Models Only) and Storing Speed Dial Numbers.

Dec 03, 2010 | Brother IntelliFax-2820 Laser Fax

1 Answer


MEMORY IS FULL / SEE MANUAL (alternating messages)
The memory is full. You may have too many messages recorded in the answering machine. To erase messages, see below. This may occur during fax reception if too much data is received before the pages can be printed out. If faxes have been received to memory because printing is not possible (an additional message will indicate the problem), resolve the problem so that printing can continue (see Substitute Reception to Memory on page 66). If you are attempting to transmit from memory, see If the memory becomes full on page 57. If you are copying, see If MEMORY IS FULL appears on page 67.

Erasing received messages:
It is important to erase received messages after you listen to them to ensure
that the memory does not become full.
? Erasing all messages: To erase all messages, press FUNCTION, DELETE, and then START/MEMORY.
? Erasing a single message: To erase a single message, press DELETE while the message is being played.

If the memory becomes full while the document is being scanned, MEMORY
IS FULL and SEE MANUAL will alternately appear in the display.
? Press START / MEMORY if you want to transmit the pages which have been stored up to that point in memory. The remaining pages will be ejected from the feeder. After transmission, the memory will be cleared and you can transmit the remaining pages. You will also need to transmit the page which was being scanned when the memory filled up.
? Press STOP if you want to cancel the entire transmission.

Nov 25, 2010 | Sharp Fax Machines

1 Answer

Error 77 message

The 77 error is caused by a fuser temperature sensor. The following steps can be used to possibly reset the Intellifax 4100 77 error.

1. Unplug machine then wait 15-20 minutes.
2. Hold down menu key. Plug in machine.
3. Release menu key at maintenance message.
4. press 91 then set button
5. press 99 then set button
6. Machine will warm up.
7. Press Reports key, then press 1. This will test if the machine can
If these steps do not reset the error the thermal fuse would have to be replaced by a repair technician.

Jul 22, 2010 | Brother IntelliFAX 4100 Laser Fax

1 Answer

How can I erase the memory to make space for new

1. Press Menu/Set, 8, 4.
2. Press Fax start
3. Press Stop/exit.

This will print all faxes held in memory, per the manufacturer's manual I found online. It worked. No more clogged memory.

Jan 22, 2010 | Brother IntelliFAX 775 Plain Paper Thermal...

1 Answer

How do i reset the message change drum soon on

Press Clear.
8 Press 1 and when the LCD shows ACCEPTED,
and then close the front cover.

Jun 05, 2009 | Brother IntelliFAX 4100 Laser Fax

1 Answer

Memory full

1. Fax Storage may be set to On. When Fax Storage is set to On, a copy of all received faxes are stored in the memory, thus using up a % of the memory available for other functions. The Fax Storage feature is utilized for Fax Forwarding, Fax Paging and Remote Retrieval. If you do not need these features, Fax Storage should be set to Off. Verify Fax Storage is set to Off by doing the following:

a. Press FUNCTION, 8 (Remote Fax Opt), then 2 (Fax Storage).

b. Check the setting. The display will read On or Off.

c. If the setting is On, press the left or right navigation key (arrows) until the display reads Off.

d. Press SET and then STOP/EXIT.

e. If you have faxes stored in the memory, you will receive a message that reads Erase all fax 1. Yes 2. No. This means you have faxes saved in the memory. If you do not want to reprint the saved faxes, press 1 (Yes) and then STOP/EXIT. After pressing 1 (Yes), all fax data is erased and Fax Storage is turned off.

Hope this helps!

May 20, 2008 | Brother IntelliFAX 770 Plain Paper Thermal...

1 Answer

Memory full

You need to print them, that should erase them from memory.

Mar 28, 2008 | Brother IntelliFAX 775 Plain Paper Thermal...

1 Answer

Warning message

try resetting the machine by pressing the features button and then in fast sequence 2,8,6,4, if you do it right it should flash test mode, then enter 91, and after you do this enter 99 to get out of the test mode

Feb 23, 2008 | Brother IntelliFax-2820 Laser Fax

Not finding what you are looking for?
Brother IntelliFAX 775 Plain Paper Thermal transfer Fax Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Fax Machines Experts


Level 3 Expert

1113 Answers

Paul King
Paul King

Level 3 Expert

727 Answers

john archer

Level 2 Expert

186 Answers

Are you a Brother Fax Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides