Question about Wasp WWS800 Handheld

1 Answer

Beep Setting Scanner is beeping too loud, how to adjust it less noisy

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 79 Answers
Re: Beep Setting

On the left, at the rear of the scanner, there are three holes.
Place your finger...!

Print this message and scan one of the following barcodes:

Posted on Jan 04, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Wrist barcode reader WT4000 how to adjust volume control

in emulation parameters you can adjust
system sounds
beep sounds

Feb 28, 2011 | Zebra WT4000 Wireless Wearable Barcode...

1 Answer

I was in the middle of an order and the red scaning light still working but will not scan the product, I downloaded what was on the scanner and that worked, but still not getting a beep after scanning the...

Push and hold down the big button for a while until it beeps. This scanner has a feature to disable the confirm beep that gets activated if you hold down the scan button too long!
Regards, Alan

Oct 05, 2010 | Opticon OPN 2001 Mobile Data Collector...

1 Answer

I have a barcode scanner Symbol S/N M1J82M51E. When scanning the item barcode it makes very low volume. How to increase the bipping scanning volume for the Symbol Scanner?

1. Press and hold the trigger for an extended period of time (approximately 5 seconds). The scanner cycles through three settings (Low, Medium, High) emitting a 2-beep tone at each setting.
2. To select a particular setting, release the trigger after you hear the desired 2-beep tone.

Sep 18, 2010 | Symbol LS9208 Hands Free Barcode Scanner

3 Answers

I need to turn off the beep on the Symbol MC9090 when I use the barcode scanner

What I have done is I taped the speaker opening on the back of the scanner with two stickers to reduce the beep volume to almost zero. So 3 to 4 stickers would probably eliminate the beep completely.

May 20, 2010 | Symbol MC9090 Barcode Scanner

2 Answers

I have not instruction for default settig where are barcode for default setting

Check metroselect single line configuration guide page no. 2
1) Scan Enter/Exit configuration mode it gives 3 beeps
2)Scan recall defaults it gives single beep
3)Scan Enter /exit configuration mode it gives 3 beeps
Now scanner is set to default setting

Sep 16, 2009 | Microsoft Metrologic MS9520 Voyager...

1 Answer

LS4278 makes the same beep with a valid code vs an invalid code

Contact the Symbol Help-desk at 1-800-653-5350. What you are asking is not possible with the LS4278. What you are probably hearing at the grocery store is the cash register software generating an error beep. The LS4278 is really just a simple scanner( eben though it is cordless) but it has no memory, and therefore cannot be loaded with a database for error correction. That is being generated by the software at the store, not thye scanner itself. For clarification, uyou can call me at the office:

Bill Matisz,
qdata inc.

Jun 29, 2009 | Symbol LS2208 Handheld

1 Answer

Symbol ls 4000i not scanning

The first beep is a Good decode beep, the four beeps later are telling that the connection to your PC is not working properly.

Jun 07, 2009 | Symbol LS 4000i Handheld

1 Answer

4 beep error when scanning barcode

The four beep error is a communications error. Usually it indicates the scanne is not configured properly. If the scanner is connecting with the CBA-K01-S07PAR cable and you are using a PS/2 keyboard you should have scanned the IBM PC/AT barcode from Adobe page 56 of 342 of the LS2208 Product Reference Guide.

If you do not have a PS/2 keyboard attached and are using a USB to PS/2 adapter you should scan the IBM AT Notebook from that same page. If the scanner does not start working immediately you may have to reboot your system. If the scanner still does not work the CBA-U01-S07ZAR USB cable might be a better choice.

If you are not connecting with either of these cables and are still getting the four beep error a call to the Motorola support center may be in order. Their phone number is 800-653-5350.

Apr 14, 2009 | Symbol LS2208-7AZK0100S Handheld

1 Answer

Extra zero

The default setting for this scanner is EAN13 enabled. This means that all 12 character barcodes will be changed to 13 characters by adding a zero in front.
How to Disable:

Open the manual that came with the scanner (it's available to download on the Cipherlab web page if you don't have it).
Find the UPCA Parameters barcodes (currently page 29). The next heading down is Convert to EAN13. You will see the disable and enable barcodes.

1) Scan Enter Setup Barcode (on practically every page of the manual at the bottom). The scanner will beep 6 times.
2) Scan the Convert to EAN13 Disable barcode. The scanner will beep once.
3) Scan the Update barcode at the bottom of the same page.

Your scanner should now read both 12 and 13 character barcodes correctly.

Hope this helps:)

Nov 26, 2008 | CIPHERLAB 1000 Handheld Barcode Scanner

1 Answer

Symbol Spark LS 1004 Problem

What do you mean? you can only scan not more than 3 times? If that so,you need to change the setting of your scanner there was a limit numbers to scan. You can check by using the manual of that scanner.

Hope you like my solution please rate me SOLVE.

Best regards,


Oct 18, 2007 | Symbol Spark LS 1004

Not finding what you are looking for?
Wasp WWS800 Handheld Logo

Related Topics:

1,247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Wasp Barcode Scanners Experts


Level 3 Expert

18258 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Wasp Barcode Scanner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides